Finisher-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, mib-2 FROM SNMPv2-SMI -- [RFC2578] MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF -- [RFC2580] hrDeviceIndex FROM HOST-RESOURCES-MIB -- [RFC2790] PrtInputTypeTC, PrtMarkerSuppliesTypeTC FROM IANA-PRINTER-MIB -- [RFC3805] printmib, PrtSubUnitStatusTC, PrtLocalizedDescriptionStringTC, PrtMarkerSuppliesSupplyUnitTC, PrtMediaUnitTC, PrtCapacityUnitTC, PrtMarkerSuppliesClassTC, PresentOnOff, prtMIBConformance FROM Printer-MIB -- [RFC3805] FinDeviceTypeTC, FinAttributeTypeTC FROM IANA-FINISHER-MIB; finisherMIB MODULE-IDENTITY LAST-UPDATED "200406020000Z" ORGANIZATION "PWG IEEE/ISTO Printer Working Group" CONTACT-INFO "Harry Lewis IBM Phone (303) 924-5337 Email: harryl@us.ibm.com Send comments to the printmib WG using the Finisher MIB Project (FIN) Mailing List: fin@pwg.org For further information, access the PWG web page under 'Finisher MIB': http://www.pwg.org/ Implementers of this specification are encouraged to join the fin mailing list in order to participate in discussions on any clarifications needed and registration proposals being reviewed in order to achieve consensus." DESCRIPTION "The MIB module for management of printers. Copyright (C) The Internet Society (2004). This version of this MIB module was published in RFC 3806. For full legal notices see the RFC itself." REVISION "200406020000Z" DESCRIPTION "The original version of this MIB." ::= { mib-2 111 } -- Finisher Device Group (Mandatory) -- -- A printer may support zero or more finishing subunits. A -- finishing device subunit may be associated with one or more -- output subunits and one or more media path subunits. finDevice OBJECT IDENTIFIER ::= { printmib 30 } finDeviceTable OBJECT-TYPE SYNTAX SEQUENCE OF FinDeviceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table defines the finishing device subunits, including information regarding possible configuration options and the status for each finisher device subunit." ::= { finDevice 1 } finDeviceEntry OBJECT-TYPE SYNTAX FinDeviceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is an entry in the finishing device table for each possible finisher process. Each individual finisher process is implemented by a finishing device represented in this table." INDEX { hrDeviceIndex, finDeviceIndex } ::= { finDeviceTable 1 } FinDeviceEntry ::= SEQUENCE { finDeviceIndex Integer32, finDeviceType FinDeviceTypeTC, finDevicePresentOnOff PresentOnOff, finDeviceCapacityUnit PrtCapacityUnitTC, finDeviceMaxCapacity Integer32, finDeviceCurrentCapacity Integer32, finDeviceAssociatedMediaPaths OCTET STRING, finDeviceAssociatedOutputs OCTET STRING, finDeviceStatus PrtSubUnitStatusTC, finDeviceDescription PrtLocalizedDescriptionStringTC } finDeviceIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique value used to identify a finisher process. Although these values may change due to a major reconfiguration of the printer system (e.g., the addition of new finishing processes), the values are normally expected to remain stable across successive power cycles." ::= { finDeviceEntry 1 } finDeviceType OBJECT-TYPE SYNTAX FinDeviceTypeTC MAX-ACCESS read-only STATUS current DESCRIPTION "Defines the type of finishing process associated with this table row entry." ::= { finDeviceEntry 2 } finDevicePresentOnOff OBJECT-TYPE SYNTAX PresentOnOff MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates if this finishing device subunit is available and whether the device subunit is enabled." DEFVAL { notPresent } ::= { finDeviceEntry 3 } finDeviceCapacityUnit OBJECT-TYPE SYNTAX PrtCapacityUnitTC MAX-ACCESS read-only STATUS current DESCRIPTION "The unit of measure for specifying the capacity of this finisher device subunit." ::= { finDeviceEntry 4 } finDeviceMaxCapacity OBJECT-TYPE SYNTAX Integer32 (-2..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum capacity of this finisher device subunit in finDeviceCapacityUnits. If the device can reliably sense this value, the value is sensed by the finisher device and is read-only: otherwise the value may be written by a management or control console application. The value (-1) means other and specifically indicates that the device places no restrictions on this parameter. The value (-2) means unknown." DEFVAL { -2 } -- unknown ::= { finDeviceEntry 5 } finDeviceCurrentCapacity OBJECT-TYPE SYNTAX Integer32 (-2..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The current capacity of this finisher device subunit in finDeviceCapacityUnits. If the device can reliably sense this value, the value is sensed by the finisher and is read-only: otherwise the value may be written by a management or control console application. The value (-1) means other and specifically indicates that the device places no restrictions on this parameter. The value (-2) means unknown." DEFVAL { -2 } -- unknown ::= { finDeviceEntry 6 } finDeviceAssociatedMediaPaths OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..63)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the media paths which can supply media for this finisher device. The value of this object is a bit map in an octet string with each position representing the value of a prtMediaPathIndex. For a media path that can be a source for this finisher device subunit, the bit position equal to one less than the value of prtMediaPathIndex will be set. The bits are numbered starting with the most significant bit of the first byte being bit 0, the least significant bit of the first byte being bit 7, the most significant of the second byte being bit 8, and so on." ::= { finDeviceEntry 7 } finDeviceAssociatedOutputs OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..63)) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the printer output subunits this finisher device subunit services. The value of this object is a bit map in an octet string with each position representing the value of a prtOutputIndex. For an output subunit that is serviced by this finisher device subunit, the bit position equal to one less than the value of prtOutputIndex will be set. The bits are numbered starting with the most significant bit of the first byte being bit 0, the least significant bit of the first byte being bit 7, the most significant of the second byte being bit 8, and so on." ::= { finDeviceEntry 8 } finDeviceStatus OBJECT-TYPE SYNTAX PrtSubUnitStatusTC MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the current status of this finisher device subunit." DEFVAL { 5 } -- unknown ::= { finDeviceEntry 9 } finDeviceDescription OBJECT-TYPE SYNTAX PrtLocalizedDescriptionStringTC MAX-ACCESS read-only STATUS current DESCRIPTION "A free form text description of this device subunit in the localization specified by prtGeneralCurrentLocalization." ::= { finDeviceEntry 10 } -- Finisher Supply Group (Mandatory) -- -- A finisher device, but not all finisher devices, may have one or more -- supplies associated with it. For example a finisher may use both -- binding tape and stitching wire supplies. A finisher may also have -- more than one source for a given type of supply e.g., multiple supply -- sources of ink for imprinters. finSupply OBJECT IDENTIFIER ::= { printmib 31 } finSupplyTable OBJECT-TYPE SYNTAX SEQUENCE OF FinSupplyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each unique source of supply is an entry in the finisher supply table. Each supply entry has its own characteristics associated with it such as colorant and current supply level." ::= { finSupply 1 } finSupplyEntry OBJECT-TYPE SYNTAX FinSupplyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of finisher devices, with their associated supplies and supplies characteristics." INDEX { hrDeviceIndex, finSupplyIndex } ::= { finSupplyTable 1 } FinSupplyEntry ::= SEQUENCE { finSupplyIndex Integer32, finSupplyDeviceIndex Integer32, finSupplyClass PrtMarkerSuppliesClassTC, finSupplyType PrtMarkerSuppliesTypeTC, finSupplyDescription PrtLocalizedDescriptionStringTC, finSupplyUnit PrtMarkerSuppliesSupplyUnitTC, finSupplyMaxCapacity Integer32, finSupplyCurrentLevel Integer32, finSupplyColorName OCTET STRING } finSupplyIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique value used by a finisher to identify this supply container/receptacle. Although these values may change due to a major reconfiguration of the finisher (e.g., the addition of new supply sources to the finisher), values are normally expected to remain stable across successive power cycles." ::= { finSupplyEntry 1 } finSupplyDeviceIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of finDeviceIndex corresponding to the finishing device subunit with which this finisher supply is associated. The value zero indicates the associated finishing device is Unknown." ::= { finSupplyEntry 2 } finSupplyClass OBJECT-TYPE SYNTAX PrtMarkerSuppliesClassTC MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates whether this supply entity represents a supply that is consumed or a container that is filled." ::= { finSupplyEntry 3 } finSupplyType OBJECT-TYPE SYNTAX PrtMarkerSuppliesTypeTC MAX-ACCESS read-only STATUS current DESCRIPTION "The type of this supply." ::= { finSupplyEntry 4 } finSupplyDescription OBJECT-TYPE SYNTAX PrtLocalizedDescriptionStringTC MAX-ACCESS read-only STATUS current DESCRIPTION "The description of this supply/receptacle in text useful for operators and management applications and in the localization specified by prtGeneralCurrentLocalization." ::= { finSupplyEntry 5 } finSupplyUnit OBJECT-TYPE SYNTAX PrtMarkerSuppliesSupplyUnitTC MAX-ACCESS read-only STATUS current DESCRIPTION "Unit of measure of this finisher supply container or receptacle." ::= { finSupplyEntry 6 } finSupplyMaxCapacity OBJECT-TYPE SYNTAX Integer32 (-2..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum capacity of this supply container/receptacle expressed in Supply Units. If this supply container/ receptacle can reliably sense this value, the value is sensed and is read-only; otherwise the value may be written by a control panel or management application. The value (-1) means other and places no restrictions on this parameter. The value (-2) means unknown." DEFVAL { -2 } -- unknown ::= { finSupplyEntry 7 } finSupplyCurrentLevel OBJECT-TYPE SYNTAX Integer32 (-3..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The current level if this supply is a container; the remaining space if this supply is a receptacle. If this supply container/receptacle can reliably sense this value, the value is sensed and is read-only; otherwise the value may be written by a control panel or management application. The value (-1) means other and places no restrictions on this parameter. The value (-2) means unknown. A value of (-3) means that the printer knows there is some supply or remaining space." DEFVAL { -2 } -- unknown ::= { finSupplyEntry 8 } -- Capacity Attribute Relationships -- -- MEDIA INPUT MEASUREMENT -- -- _______ | | -- | | | -- | | | | -- | |_ _ _ _ _ _ _ _ _ _| ________________ |direction -- | | | | v -- MaxCapacity | | | -- | | Sheets remaining | CurrentLevel -- | | | | -- v | | v -- _______ +___________________+ _______ finSupplyColorName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..63)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of the color associated with this supply." REFERENCE "The PWG Standardized Media Names specification [PWGMEDIA], section 4 Media Color Names, contains the recommended values for this object. Implementers may add additional string values. The naming conventions in ISO 9070 are recommended in order to avoid potential name clashes." ::= { finSupplyEntry 9 } -- Finisher Supply, Media Input Group (Conditionally Mandatory) -- -- A finisher device may have one or more associated supply media -- inputs. Each entry in this table defines an input for a -- supply media type such as inserts, covers, etc. -- -- This group is mandatory only if the printer system contains a -- finisher device that requires a media supply used exclusively by a -- finishing process. Examples are inserts or covers that are not -- supplied by an input subunit that provides media to the marker. finSupplyMediaInput OBJECT IDENTIFIER ::= { printmib 32 } finSupplyMediaInputTable OBJECT-TYPE SYNTAX SEQUENCE OF FinSupplyMediaInputEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The input subunits associated with a finisher supply media are each represented by an entry in this table." ::= { finSupplyMediaInput 1 } finSupplyMediaInputEntry OBJECT-TYPE SYNTAX FinSupplyMediaInputEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of finisher supply media input subunit features and characteristics." INDEX { hrDeviceIndex, finSupplyMediaInputIndex } ::= { finSupplyMediaInputTable 1 } FinSupplyMediaInputEntry ::= SEQUENCE { finSupplyMediaInputIndex Integer32, finSupplyMediaInputDeviceIndex Integer32, finSupplyMediaInputSupplyIndex Integer32, finSupplyMediaInputType PrtInputTypeTC, finSupplyMediaInputDimUnit PrtMediaUnitTC, finSupplyMediaInputMediaDimFeedDir Integer32, finSupplyMediaInputMediaDimXFeedDir Integer32, finSupplyMediaInputStatus PrtSubUnitStatusTC, finSupplyMediaInputMediaName OCTET STRING, finSupplyMediaInputName OCTET STRING, finSupplyMediaInputDescription PrtLocalizedDescriptionStringTC, finSupplyMediaInputSecurity PresentOnOff, finSupplyMediaInputMediaWeight Integer32, finSupplyMediaInputMediaThickness Integer32, finSupplyMediaInputMediaType OCTET STRING } finSupplyMediaInputIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique value used by a finisher to identify this supply media input subunit. Although these values may change due to a major reconfiguration of the finisher (e.g., the addition of new supply media input sources to the finisher), values are normally expected to remain stable across successive power cycles." ::= { finSupplyMediaInputEntry 1 } finSupplyMediaInputDeviceIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of finDeviceIndex corresponding to the finishing device subunit with which this finisher media supply is associated. The value zero indicates the associated device is unknown." ::= { finSupplyMediaInputEntry 2 } finSupplyMediaInputSupplyIndex OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of finSupplyIndex corresponding to the finishing supply subunit with which this finisher media supply is associated. The value zero indicates the associated finishing supply is unknown or there is no applicable finisher supply table entry." ::= { finSupplyMediaInputEntry 3 } finSupplyMediaInputType OBJECT-TYPE SYNTAX PrtInputTypeTC MAX-ACCESS read-only STATUS current DESCRIPTION "The type of technology (discriminated primarily according to the feeder mechanism type) employed by the input subunit." ::= { finSupplyMediaInputEntry 4 } finSupplyMediaInputDimUnit OBJECT-TYPE SYNTAX PrtMediaUnitTC MAX-ACCESS read-only STATUS current DESCRIPTION "The unit of measure for specifying dimensional values for this input device." ::= { finSupplyMediaInputEntry 5 } finSupplyMediaInputMediaDimFeedDir OBJECT-TYPE SYNTAX Integer32 (-2..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This object provides the value of the dimension in the feed direction of the media that is placed or will be placed in this input device. Feed dimension measurements are taken parallel to the feed direction of the device and measured in finSupplyMediaInputDimUnits. If this input device can reliably sense this value, the value is sensed and is read-only access. Otherwise the value is read-write access and may be written by management or control panel applications. The value (-1) means other and specifically indicates that this device places no restrictions on this parameter. The value (-2) indicates unknown. " ::= { finSupplyMediaInputEntry 6 } finSupplyMediaInputMediaDimXFeedDir OBJECT-TYPE SYNTAX Integer32 (-2..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This object provides the value of the dimension across the feed direction of the media that is placed or will be placed in this input device. The cross feed direction is ninety degrees relative to the feed direction on this device and measured in finSupplyMediaInputDimUnits. If this input device can reliably sense this value, the value is sensed and is read-only access. Otherwise the value is read-write access and may be written by management or control panel applications. The value (-1) means other and specifically indicates that this device places no restrictions on this parameter. The value (-2) indicates unknown. " ::= { finSupplyMediaInputEntry 7 } finSupplyMediaInputStatus OBJECT-TYPE SYNTAX PrtSubUnitStatusTC MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates the current status of this input device." DEFVAL { 5 } -- unknown ::= { finSupplyMediaInputEntry 8 } finSupplyMediaInputMediaName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..63)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the current media contained in this input device. Examples are Engineering Manual Cover, Section A Tab Divider or any ISO standard names." ::= { finSupplyMediaInputEntry 9 } finSupplyMediaInputName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..63)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name assigned to this input subunit." ::= { finSupplyMediaInputEntry 10 } finSupplyMediaInputDescription OBJECT-TYPE SYNTAX PrtLocalizedDescriptionStringTC MAX-ACCESS read-only STATUS current DESCRIPTION "A free form text description of this input subunit in the localization specified by prtGeneralCurrentLocalization." ::= { finSupplyMediaInputEntry 11 } finSupplyMediaInputSecurity OBJECT-TYPE SYNTAX PresentOnOff MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates if this subunit has some security associated with it." ::= { finSupplyMediaInputEntry 12 } finSupplyMediaInputMediaWeight OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The weight of the media associated with this Input device in grams per meter squared. The value (-1) means other and specifically indicates that the device places no restriction on this parameter. The value (-2) means unknown. This object can be used to calculate the weight of individual pages processed by the document finisher. This value, when multiplied by the number of pages in a finished set, can be used to calculate the weight of a set before it is inserted into a mailing envelope." ::= { finSupplyMediaInputEntry 13 } finSupplyMediaInputMediaThickness OBJECT-TYPE SYNTAX Integer32 (-2..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "This object identifies the thickness of the input media processed by this document input subunit measured in micrometers. This value may be used by devices (or operators) to set up proper machine tolerances for the feeder operation. The value (-2) indicates that the media thickness is unknown or not used in the setup for this input subunit." ::= { finSupplyMediaInputEntry 14 } finSupplyMediaInputMediaType OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..63)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the type of medium associated with this input subunit. " REFERENCE "The PWG Standardized Media Names specification [PWGMEDIA], section 3 Media Type Names, contains the recommended values for this object. Implementers may add additional string values. The naming conventions in ISO 9070 are recommended in order to avoid potential name clashes." ::= { finSupplyMediaInputEntry 15 } -- Finisher Device Attribute Group (Mandatory) -- -- A finisher device subunit may have one or more parameters that -- cannot be specified by any other objects in the MIB. The -- Device Attribute group facilitates the definition of these -- parameters. The objects which define the attributes are -- read-write, to allow both Set and Get operations. -- -- At least one table entry must exist for each finisher device defined -- by the MIB. If no other entry is possible for a finisher device, the -- deviceName(3) attribute MUST be returned. finDeviceAttribute OBJECT IDENTIFIER ::= { printmib 33 } finDeviceAttributeTable OBJECT-TYPE SYNTAX SEQUENCE OF FinDeviceAttributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The attribute table defines special parameters that are applicable only to a minority of the finisher devices. An attribute table entry is used, rather than unique objects, to minimize the number of MIB objects and to allow for expansion without the addition of MIB objects. Each finisher device is represented by a separate row in the device subunit attribute table." ::= { finDeviceAttribute 1 } finDeviceAttributeEntry OBJECT-TYPE SYNTAX FinDeviceAttributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry defines a finisher function parameter that cannot be represented by an object in the finisher device subunit table." INDEX { hrDeviceIndex, finDeviceIndex, finDeviceAttributeTypeIndex, finDeviceAttributeInstanceIndex } ::= { finDeviceAttributeTable 1 } FinDeviceAttributeEntry ::= SEQUENCE { finDeviceAttributeTypeIndex FinAttributeTypeTC, finDeviceAttributeInstanceIndex Integer32, finDeviceAttributeValueAsInteger Integer32, finDeviceAttributeValueAsOctets OCTET STRING } finDeviceAttributeTypeIndex OBJECT-TYPE SYNTAX FinAttributeTypeTC MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines the attribute type represented by this row." ::= { finDeviceAttributeEntry 1 } finDeviceAttributeInstanceIndex OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index that allows the discrimination of an attribute instance when the same attribute occurs multiple times for a specific instance of a finisher function. The value of this index shall be 1 if only a single instance of the attribute occurs for the specific finisher function. Additional values shall be assigned in a contiguous manner." ::= { finDeviceAttributeEntry 2 } finDeviceAttributeValueAsInteger OBJECT-TYPE SYNTAX Integer32 (-2..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "Defines the integer value of the attribute. The value of the attribute is represented as an integer if the finAttributeTypeTC description for the attribute has the tag 'INTEGER:'. Depending upon the attribute enum definition, this object may be either an integer, a counter, an index, or an enum. Attributes for which the concept of an integer value is not meaningful SHALL return a value of -1 for this attribute." DEFVAL { -2 } -- unknown ::= { finDeviceAttributeEntry 3 } finDeviceAttributeValueAsOctets OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..63)) MAX-ACCESS read-write STATUS current DESCRIPTION "Contains the octet string value of the attribute. The value of the attribute is represented as a string if the finAttributeTypeTC description for the attribute has the tag 'OCTETS:'. Depending upon the attribute enum definition, this object may be either a coded character set string (text) or a binary octet string. Attributes for which the concept of an octet string value is not meaningful SHALL contain a zero length string." DEFVAL { ''H } -- empty string ::= { finDeviceAttributeEntry 4 } -- Conformance Information -- compliance statements finMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for agents that implement the finisher MIB." MODULE -- this module MANDATORY-GROUPS { finDeviceGroup, finSupplyGroup, finDeviceAttributeGroup } OBJECT finDevicePresentOnOff MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finDeviceMaxCapacity MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finDeviceCurrentCapacity MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finSupplyMaxCapacity MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finSupplyCurrentLevel MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finSupplyMediaInputMediaDimFeedDir MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finSupplyMediaInputMediaDimXFeedDir MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finSupplyMediaInputMediaName MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finSupplyMediaInputName MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finSupplyMediaInputSecurity MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finSupplyMediaInputMediaWeight MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finSupplyMediaInputMediaThickness MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finSupplyMediaInputMediaType MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finDeviceAttributeValueAsInteger MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." OBJECT finDeviceAttributeValueAsOctets MIN-ACCESS read-only DESCRIPTION "It is conformant to implement this object as read-only." GROUP finSupplyMediaInputGroup DESCRIPTION "This group is conditionally mandatory and must be included if a finisher device requires a media supply that is used exclusively by a finishing process." ::= { prtMIBConformance 5 } finMIBGroups OBJECT IDENTIFIER ::= { prtMIBConformance 6 } finDeviceGroup OBJECT-GROUP OBJECTS { finDeviceType, finDevicePresentOnOff, finDeviceCapacityUnit, finDeviceMaxCapacity, finDeviceCurrentCapacity, finDeviceAssociatedMediaPaths, finDeviceAssociatedOutputs, finDeviceStatus, finDeviceDescription } STATUS current DESCRIPTION "The finisher device group." ::= { finMIBGroups 1 } finSupplyGroup OBJECT-GROUP OBJECTS { finSupplyDeviceIndex, finSupplyClass, finSupplyType, finSupplyDescription, finSupplyUnit, finSupplyMaxCapacity, finSupplyCurrentLevel, finSupplyColorName } STATUS current DESCRIPTION "The finisher supply group." ::= { finMIBGroups 2 } finSupplyMediaInputGroup OBJECT-GROUP OBJECTS { finSupplyMediaInputDeviceIndex, finSupplyMediaInputSupplyIndex, finSupplyMediaInputType, finSupplyMediaInputDimUnit, finSupplyMediaInputMediaDimFeedDir, finSupplyMediaInputMediaDimXFeedDir, finSupplyMediaInputStatus, finSupplyMediaInputMediaName, finSupplyMediaInputName, finSupplyMediaInputDescription, finSupplyMediaInputSecurity, finSupplyMediaInputMediaWeight, finSupplyMediaInputMediaThickness, finSupplyMediaInputMediaType } STATUS current DESCRIPTION "The finisher supply, media input group." ::= { finMIBGroups 3 } finDeviceAttributeGroup OBJECT-GROUP OBJECTS { finDeviceAttributeValueAsInteger, finDeviceAttributeValueAsOctets } STATUS current DESCRIPTION "The finisher device attribute group. This group is mandatory for a finisher device that contains an inserter subunit." ::= { finMIBGroups 4 } END