MSIPRIP2-MIB DEFINITIONS ::= BEGIN -- -- Microsoft(R) RIP Version 2 for Internet Protocol MIB -- -- This MIB defines the management information for the Routing Information -- Protocol Version 2 ( RIP v2). The information in this MIB is divided -- into 3 groups: -- -- 1. Global Group -- Contains the global information and statistics for the RIP protocol -- Information contained in this group is independent of the interfaces -- over which the protocol is enabled. -- -- 2. Interface Group -- Contains RIP configuration information and statistics specific -- to each interface. -- -- 3. Peer Group -- Contains statistics pertaining to RIP peers. -- IMPORTS enterprises, OBJECT-TYPE, TimeTicks, Counter, IpAddress FROM RFC1155-SMI microsoft, software FROM MSFT-MIB; -- MSIPRIP2 -- microsoft OBJECT IDENTIFIER ::= { enterprises 311 } -- software OBJECT IDENTIFIER ::= { microsoft 1 } msiprip2 OBJECT IDENTIFIER ::= { software 11 } -- -- groups in MSIPRIP2 -- global OBJECT IDENTIFIER ::= { msiprip2 1 } interface OBJECT IDENTIFIER ::= { msiprip2 2 } peer OBJECT IDENTIFIER ::= { msiprip2 3 } -- -- RIP Global Group -- -- Contains the global information and statistics for the RIP protocol -- Information contained in this group is independent of the interfaces -- over which the protocol is enabled. -- -- Global information consists of scalar variables which can be -- updated and a peer filter table -- -- Global information also contains global RIP statitics -- globalSystemRouteChanges OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of changes RIP has made to the system routing tables." ::= { global 1 } globalTotalResponseSends OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of request messages for which responses have been sent." ::= { global 2 } globalLoggingLevel OBJECT-TYPE SYNTAX INTEGER { none(1), error(2), warning(3), information(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Information logged can be None, Error only, Error + Warning, Error + Warn + Logging. This variable controls the amount of information logged" ::= { global 3 } globalMaxRecQueueSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Maximum size to use for queueing incoming packets." ::= { global 4 } globalMaxSendQueueSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Maximum size to use for queueing outgoing packets." ::= { global 5 } globalMinTriggeredUpdateInterval OBJECT-TYPE SYNTAX TimeTicks ACCESS read-write STATUS mandatory DESCRIPTION "Minimum lag time before sending a triggered update. Used to consolidate updates to the route table and reduce number of updates sent." ::= { global 6 } globalPeerFilterMode OBJECT-TYPE SYNTAX INTEGER { disable(1), include(2), exclude(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls the use of update messages from the list of peers in the peer filter table. If set to include routes will be only be accepted if they are from the routers in the peer array. If set to exclude routes will be rejected that come from the routers whose addresses are in the peer array, and all other routers will be accepted." ::= { global 7 } globalPeerFilterCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of entries in the peer filter table" ::= { global 8} -- -- the Peer filter Table -- -- -- Entries in the peer filter table are IP addresses of routers that -- interact with this router via RIP. The use of the entries in this table -- is controlled by the global variable "globalPeerFilterMode" -- globalPeerFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF GlobalPeerFilterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of peer routers communicating with this router via RIP" ::= { global 9 } globalPeerFilterEntry OBJECT-TYPE SYNTAX GlobalPeerFilterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Peer router entry. Contains the IP address of peer router" INDEX { globalPFAddr } ::= { globalPeerFilterTable 1 } GlobalPeerFilterEntry ::= SEQUENCE { globalPFAddr IpAddress, globalPFTag INTEGER } globalPFAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "IP Address of peer router" ::= { globalPeerFilterEntry 1 } globalPFTag OBJECT-TYPE SYNTAX INTEGER { create(1), delete(2) } ACCESS read-write STATUS mandatory DESCRIPTION "create : Creates an entry in the Global Peer Filter table delete : Deletes an entry in the Global Peer Filter table " ::= { globalPeerFilterEntry 2 } -- -- RIP Interface group -- -- Contains RIP interface configuration information, RIP interface -- statistics and RIP interface binding information. Each type of -- information is stored in a table with one entry for each -- interface over which RIP is enabled. -- -- Asscociated with each entry in the Interface Config table is a -- list of entries in the -- Unicast peer table : List of peers to which the update -- message is unicast. -- Accept Route Filter Table : List of routes used to filter the -- accepted routes. -- Announce Route Filter Table : List of routes used to filter the -- annouced routes -- -- Asscociated with each entry in the Interface binding table is a -- list of entries in the -- -- Interface Address Table : List of address bound to an interface -- -- -- Interface Statistics Table. -- -- -- RIP statistics for each interface. Statistics include -- number of requests/responses sent/received, -- number of send/receive failures -- number of triggered updates sent -- number of bad packet/entries revceived. -- ifStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF IfStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of RIP statistics for interfaces" ::= { interface 1 } ifStatsEntry OBJECT-TYPE SYNTAX IfStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "RIP interface statistics entry. Each entry contains counts of send/receive failures, requests/resposes sent/received, bad packets/entries reveived and triggered updates sent" INDEX { ifSEIndex } ::= { ifStatsTable 1 } IfStatsEntry ::= SEQUENCE { ifSEIndex INTEGER, ifSEState INTEGER, ifSESendFailures Counter, ifSEReceiveFailures Counter, ifSERequestSends Counter, ifSERequestReceiveds Counter, ifSEResponseSends Counter, ifSEResponseReceiveds Counter, ifSEBadResponsePacketReceiveds Counter, ifSEBadResponseEntriesReceiveds Counter, ifSETriggeredUpdateSends Counter } ifSEIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Index for the RIP interface Statistics table" ::= { ifStatsEntry 1 } ifSEState OBJECT-TYPE SYNTAX INTEGER { enabled(1), bound(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Current state of RIP on this interface." ::= { ifStatsEntry 2 } ifSESendFailures OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of times a failure occurred while attempting to send a packet on this interface." ::= { ifStatsEntry 3 } ifSEReceiveFailures OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of times a failure occurred while attempting to receive a packet on this interface." ::= { ifStatsEntry 4 } ifSERequestSends OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of RIP REQUEST packets sent on this interface." ::= { ifStatsEntry 5 } ifSERequestReceiveds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of RIP REQUEST packets received on this interface." ::= { ifStatsEntry 6 } ifSEResponseSends OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of RIP RESPONSE packets sent on this interface." ::= { ifStatsEntry 7 } ifSEResponseReceiveds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of RIP RESPONSE packets received on this interface." ::= { ifStatsEntry 8 } ifSEBadResponsePacketReceiveds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of RIP RESPONSE packets discarded due to errors in the header." ::= { ifStatsEntry 9 } ifSEBadResponseEntriesReceiveds OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of RIP RESPONSE routes ignored due to errors in the entry." ::= { ifStatsEntry 10 } ifSETriggeredUpdateSends OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of triggered updates sent. " ::= { ifStatsEntry 11 } -- -- RIP Interface Configuration Table. -- -- -- RIP Interface config includes the interface setting for : -- -- update, annouce and accept modes, -- full update, route expiration and route removal intervals, -- Unicast peer, accept/annouce filter counts and -- authentication information. -- -- Associated with each interface entry in this table, there are a -- set of entries in -- -- RIP Unicast Peer Table -- RIP Announce Fitler Table -- RIP Accept Filter Table. -- -- The use of the entries in each of the above tables is controlled -- by the value of the respective modes in the interface config setting -- ifConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF IfConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "RIP Interface configuration table. List of subnets that require separate configuration in RIP." ::= { interface 2 } ifConfigEntry OBJECT-TYPE SYNTAX IfConfigEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "RIP configuration entry for an interface. A single routing domain in a single subnet." INDEX { ifCEIndex } ::= { ifConfigTable 1 } IfConfigEntry ::= SEQUENCE { ifCEIndex INTEGER, ifCEState INTEGER, ifCEMetric INTEGER, ifCEUpdateMode INTEGER, ifCEAcceptMode INTEGER, ifCEAnnounceMode INTEGER, ifCEProtocolFlags INTEGER, ifCERouteExpirationInterval TimeTicks, ifCERouteRemovalInterval TimeTicks, ifCEFullUpdateInterval TimeTicks, ifCEAuthenticationType INTEGER, ifCEAuthenticationKey OCTET STRING, ifCERouteTag INTEGER, ifCEUnicastPeerMode INTEGER, ifCEAcceptFilterMode INTEGER, ifCEAnnounceFilterMode INTEGER, ifCEUnicastPeerCount INTEGER, ifCEAcceptFilterCount INTEGER, ifCEAnnounceFilterCount INTEGER } ifCEIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Index for RIP interface config. table." ::= { ifConfigEntry 1 } ifCEState OBJECT-TYPE SYNTAX INTEGER { enabled(1), bound(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Current state of RIP on this interface." ::= { ifConfigEntry 2 } ifCEMetric OBJECT-TYPE SYNTAX INTEGER (0..16) ACCESS read-write STATUS mandatory DESCRIPTION "Metric for the network connected to this interface." DEFVAL { 1 } ::= { ifConfigEntry 3 } ifCEUpdateMode OBJECT-TYPE SYNTAX INTEGER { periodic(1), demand(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Mode for sending update messages. If set to periodic, then messages are sent based on the value of ifCEFullUpdateInterval. Otherwise update messages are sent only on demand." DEFVAL { periodic } ::= { ifConfigEntry 4 } ifCEAcceptMode OBJECT-TYPE SYNTAX INTEGER { disable(1), rip1(2), rip1Compat(3), rip2(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the type of RIP messages that will be accepted by this router disable : No RIP messages wil be accepted rip1 : Only RIP-1 messages will be accepted rip1Compat : Both RIP-1 and RIP-2 messages will be accepted rip2 : Only RIP-2 messages will be accepted" DEFVAL { rip1Compat } ::= { ifConfigEntry 5 } ifCEAnnounceMode OBJECT-TYPE SYNTAX INTEGER { disable(1), rip1(2), rip1Compat(3), rip2(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the type of RIP messages that will be sent by this router. disable : No RIP messages wil be sent rip1 : Only RIP-1 messages will be sent in compliance with RFC 1058. rip1Compat : RIP-2 messages will be broadcast using RFC 1058 subsumption rules. rip2 : RIP-2 messages will be multicast" DEFVAL { rip1Compat } ::= { ifConfigEntry 6 } ifCEProtocolFlags OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Options for control of RIP operation. These options can be used in combination. Option value -------------------------------------------------- 1. ACCEPT_HOST_ROUTES 0x00000001 2. ANNOUNCE_HOST_ROUTES 0x00000002 3. ACCEPT_DEFAULT_ROUTES 0x00000004 4. ANNOUNCE_DEFAULT_ROUTES 0x00000008 5. SPLIT_HORIZON 0x00000010 6. POISON_REVERSE 0x00000020 7. GRACEFUL_SHUTDOWN 0x00000040 8. TRIGGERED_UPDATES 0x00000080 9. OVERWRITE_STATIC_ROUTES 0x00000100 " DEFVAL { 240 } ::= { ifConfigEntry 7 } ifCERouteExpirationInterval OBJECT-TYPE SYNTAX TimeTicks ACCESS read-write STATUS mandatory DESCRIPTION "Interval after which route is marked for deletion." DEFVAL { 180 } ::= { ifConfigEntry 8 } ifCERouteRemovalInterval OBJECT-TYPE SYNTAX TimeTicks ACCESS read-write STATUS mandatory DESCRIPTION "Interval after which a route marked for deletion is removed." DEFVAL { 120 } ::= { ifConfigEntry 9 } ifCEFullUpdateInterval OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "Interval between route table annoucements." DEFVAL { 30 } ::= { ifConfigEntry 10 } ifCEAuthenticationType OBJECT-TYPE SYNTAX INTEGER { noAuthentication(1), simplePassword(2), md5(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Type of authentication to be used on this interface." DEFVAL{ noAuthentication } ::= { ifConfigEntry 11 } ifCEAuthenticationKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..16)) ACCESS read-write STATUS mandatory DESCRIPTION "The value to be used as the Authentication key whenever the corresponding instance of ifCEAuthenticationType has a value other than noAuthentication. A modification of the corresponding instance of ifCEAuthentiationType does not modify the ifCEAuthenticationKey value. If a string shorter than 16 octects is supplied, it will be left-justified and padded to 16 octects, on the right with nulls (0x00). Reading this object always results in an OCTET STRING of length zero; authentication may not be bypasssed by reading the MIB object" DEFVAL { ''h } ::= { ifConfigEntry 12 } ifCERouteTag OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Value inserted into the Routing Domain field of all RIP packets sent on this interface." DEFVAL { 0 } ::= { ifConfigEntry 13 } ifCEUnicastPeerMode OBJECT-TYPE SYNTAX INTEGER { disable(1), peerAlso(2), peerOnly(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the unicast behavior when route update messages are sent. If set to peerAlso, updates are sent to those peers in the RIP unicast peer table corresponding to this interace as well as being sent via broadcast/multicast. If set to peerOnly, updates are sent only those peers listed in in the RIP Unicast peer table corresponding to this interface." DEFVAL{ disable } ::= { ifConfigEntry 14 } ifCEAcceptFilterMode OBJECT-TYPE SYNTAX INTEGER { disable(1), include(2), exclude(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the accept behaviour of the RIP router. If set to include the entries in the Accept Filter Table corresponding to this interface specify the routes to be included. All other routes are excluded. If set to exclude the entries in the Accept Filter Table corresponding to this interface specify the routes to be excluded." DEFVAL { disable } ::= { ifConfigEntry 15 } ifCEAnnounceFilterMode OBJECT-TYPE SYNTAX INTEGER { disable(1), include(2), exclude(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines the annouce behaviour of the RIP router. If set to include the entries in the Announce Filter Table corresponding to this interface specify the routes to be included. All other routes are excluded. If set to exclude the entries in the Announce Filter Table corresponding to this interface specify the routes to be excluded." DEFVAL { disable } ::= { ifConfigEntry 16 } ifCEUnicastPeerCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Number of entries in the Unicast Peer Table corresponding to this interface entry." DEFVAL { 0 } ::= { ifConfigEntry 17 } ifCEAcceptFilterCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Number of entries in the Accept Filter Table corresponding to this interface entry." DEFVAL { 0 } ::= { ifConfigEntry 18 } ifCEAnnounceFilterCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Number of entries in the Announce Filter Table corresponding to this interface entry." DEFVAL { 0 } ::= { ifConfigEntry 19 } -- -- Unicast Peer Table -- -- -- For each interface a list of peers to which update messages are -- unicast is maintained in this table. The use of the entries -- corresponding to an interface is controlled by the -- ifCEUnicastPeerMode variable in the interface configuration. -- -- This table is indexed by an interface number and a peer router address. -- ifUnicastPeersTable OBJECT-TYPE SYNTAX SEQUENCE OF IfUnicastPeersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of the peers routers to which update messages need to be unicast" ::= { interface 3 } ifUnicastPeersEntry OBJECT-TYPE SYNTAX IfUnicastPeersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Entry for a peer router for an interface" INDEX { ifUPIfIndex, ifUPAddress } ::= { ifUnicastPeersTable 1 } IfUnicastPeersEntry ::= SEQUENCE { ifUPIfIndex INTEGER, ifUPAddress IpAddress, ifUPTag INTEGER } ifUPIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Interface index corresponding to the interface with which this peer router is associated." ::= { ifUnicastPeersEntry 1 } ifUPAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "IP Address of a peer router." ::= { ifUnicastPeersEntry 2 } ifUPTag OBJECT-TYPE SYNTAX INTEGER { create(1), delete(2) } ACCESS read-write STATUS mandatory DESCRIPTION "create : Creates an entry in the unicast peer table delete : Deletes an entry in the unicast peer table " ::= { ifUnicastPeersEntry 3 } -- -- Accept Route Filter Table -- -- -- For each interface the list of routes to be used to filter the set -- of routes to be accepted over that interface is maintained in this -- table. The use of the routes corresponding to an interface is -- determined by the setting of the ifCEAcceptRouteFilterMode in the -- interface configuration. -- -- This table is indexed by an interface number and a peer router address. -- ifAcceptRouteFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF IfAcceptRouteFilterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of the route filters used to filter the set of routes accepted over an interface." ::= { interface 4 } ifAcceptRouteFilterEntry OBJECT-TYPE SYNTAX IfAcceptRouteFilterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Entry for a route filter for an interface" INDEX { ifAcceptRFIfIndex, ifAcceptRFLoAddress, ifAcceptRFHiAddress, ifAcceptRFTag } ::= { ifAcceptRouteFilterTable 1 } IfAcceptRouteFilterEntry ::= SEQUENCE { ifAcceptRFIfIndex INTEGER, ifAcceptRFLoAddress IpAddress, ifAcceptRFHiAddress IpAddress, ifAcceptRFTag INTEGER } ifAcceptRFIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Interface index corresponding to the interface to which this route filter entry corresponds" ::= { ifAcceptRouteFilterEntry 1 } ifAcceptRFLoAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Lowest address in the range of routes covered by this filter." ::= { ifAcceptRouteFilterEntry 2 } ifAcceptRFHiAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Higher address in the range routes covered by this filter." ::= { ifAcceptRouteFilterEntry 3 } ifAcceptRFTag OBJECT-TYPE SYNTAX INTEGER { create(1), delete(2) } ACCESS read-write STATUS mandatory DESCRIPTION "create : Creates an entry in the Accept Route Filter table delete : Deletes an entry in the Accept Route Filter table " ::= { ifAcceptRouteFilterEntry 4 } -- -- Announce Route Filter Table -- -- -- For each interface the list of routes to be used to filter the set -- of routes to be annouced over that interface is maintained in this -- table. The use of the routes corresponding to an interface is -- determined by the setting of the ifCEAnnounceRouteFilterMode in the -- interface configuration. -- -- This table is indexed by an interface number and a peer router address. -- ifAnnounceRouteFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF IfAnnounceRouteFilterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of the route filters used to filter the set of routes annouced over an interface." ::= { interface 5 } ifAnnounceRouteFilterEntry OBJECT-TYPE SYNTAX IfAnnounceRouteFilterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Entry for a route filter for an interface." INDEX { ifAnnounceRFIfIndex, ifAnnounceRFLoAddress, ifAnnounceRFHiAddress } ::= { ifAnnounceRouteFilterTable 1 } IfAnnounceRouteFilterEntry ::= SEQUENCE { ifAnnounceRFIfIndex INTEGER, ifAnnounceRFLoAddress IpAddress, ifAnnounceRFHiAddress IpAddress, ifAnnounceRFTag INTEGER } ifAnnounceRFIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Interface index corresponding to the interface to which this route filter entry corresponds" ::= { ifAnnounceRouteFilterEntry 1 } ifAnnounceRFLoAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Lowest address in the range of routes covered by this filter." ::= { ifAnnounceRouteFilterEntry 2 } ifAnnounceRFHiAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "Higher address in the range routes covered by this filter." ::= { ifAnnounceRouteFilterEntry 3 } ifAnnounceRFTag OBJECT-TYPE SYNTAX INTEGER { create(1), delete(2) } ACCESS read-write STATUS mandatory DESCRIPTION "create : Creates an entry in the Announce Route Filter table delete : Deletes an entry in the Announce Route Filter table " ::= { ifAnnounceRouteFilterEntry 4 } -- -- Interface Binding Table. -- -- -- This table stores information pertaining to the binding state and the -- number of IP addresses bound to an interface. -- -- The list of IP address bound to an interface is maintained in the -- Interface Address Table -- ifBindingTable OBJECT-TYPE SYNTAX SEQUENCE OF IfBindingEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table containing binding information for each interface." ::= { interface 6 } ifBindingEntry OBJECT-TYPE SYNTAX IfBindingEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Binding information entry for an interface" INDEX { ifBindingIndex } ::= { ifBindingTable 1 } IfBindingEntry ::= SEQUENCE { ifBindingIndex INTEGER, ifBindingState INTEGER, ifBindingCounts Counter } ifBindingIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Index corresponding to an interface entry in the binding table" ::= { ifBindingEntry 1 } ifBindingState OBJECT-TYPE SYNTAX INTEGER { enabled(1), bound(2) } ACCESS read-only STATUS mandatory DESCRIPTION "State of the interface binding" ::= { ifBindingEntry 2 } ifBindingCounts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of IP address bound to this interface. This is also the number of entries in the Interface Address Table corresponding to this interface." ::= { ifBindingEntry 3 } -- -- Interface Address Table -- -- -- The Interface Address Table contains the list of address bound to -- each interface. -- -- This table is indexed by an interface number and an IP address. -- ifAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF IfAddressEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of IP addresses bound to interfaces" ::= { interface 7 } ifAddressEntry OBJECT-TYPE SYNTAX IfAddressEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Entry for an IP address for an interface" INDEX { ifAEIfIndex, ifAEAddress, ifAEMask } ::= { ifAddressTable 1 } IfAddressEntry ::= SEQUENCE { ifAEIfIndex INTEGER, ifAEAddress IpAddress, ifAEMask IpAddress } ifAEIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Index corresponding to the Interface with which this entry is associated." ::= { ifAddressEntry 1 } ifAEAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "Ip address bound to the associated interface." ::= { ifAddressEntry 2 } ifAEMask OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "Address Mask associated with the IP address contained in the corresponding ifAEAddress field." ::= { ifAddressEntry 3 } -- -- Peer Statistics Table. -- -- -- This table contains statistics for each peer router that commnicates -- with this router via RIP. -- -- This table is indexed by the IP address of the peer router. -- ifPeerStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF IfPeerStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of peer router statistics" ::= { peer 1} ifPeerStatsEntry OBJECT-TYPE SYNTAX IfPeerStatsEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Entry corresponding to a peer router." INDEX { ifPSAddress } ::= { ifPeerStatsTable 1 } IfPeerStatsEntry ::= SEQUENCE { ifPSAddress IpAddress, ifPSLastPeerRouteTag INTEGER, ifPSLastPeerUpdateTickCount TimeTicks, ifPSLastPeerUpdateVersion INTEGER, ifPSPeerBadResponsePackets Counter, ifPSPeerBadResponseEntries Counter } ifPSAddress OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "IP Address that the peer is using as its source address." ::= { ifPeerStatsEntry 1 } ifPSLastPeerRouteTag OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The route-tag of the last route in the last RIP RESPONSE received from this peer." ::= { ifPeerStatsEntry 2 } ifPSLastPeerUpdateTickCount OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The tick-count in milliseconds at the time of the last RIP RESPONSE received from this peer." ::= { ifPeerStatsEntry 3 } ifPSLastPeerUpdateVersion OBJECT-TYPE SYNTAX INTEGER ( 0..255 ) ACCESS read-only STATUS mandatory DESCRIPTION "The update version of the last RIP RESPONSE received from this peer." ::= { ifPeerStatsEntry 4 } ifPSPeerBadResponsePackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of RIP RESPONSE packets which were received from this peer and subsequently discarded." ::= { ifPeerStatsEntry 5 } ifPSPeerBadResponseEntries OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of routes in RIP RESPONSE packets which were received from this peer and subsequently discarded." ::= { ifPeerStatsEntry 6 } END