TE-LINK-STD-MIB DEFINITIONS ::= BEGIN
 
IMPORTS
   MODULE-IDENTITY, OBJECT-TYPE, transmission, Integer32, Unsigned32
      FROM SNMPv2-SMI
 
   MODULE-COMPLIANCE, OBJECT-GROUP
      FROM SNMPv2-CONF
 
   TEXTUAL-CONVENTION, RowStatus, StorageType
      FROM SNMPv2-TC
 
   InterfaceIndexOrZero, ifIndex
      FROM IF-MIB
 
   InetAddressType, InetAddress
      FROM INET-ADDRESS-MIB;
 
 
teLinkStdMIB MODULE-IDENTITY
   LAST-UPDATED "200510110000Z"  -- 11 October 2005
   ORGANIZATION "Multiprotocol Label Switching (MPLS) Working Group"
   CONTACT-INFO
       "        Martin Dubuc
        Email:  mdubuc@ncf.ca
 
                Thomas D. Nadeau
        Email:  tnadeau@cisco.com
 
 
 
 
                Jonathan P. Lang
        Email:  jplang@ieee.org
 
        Comments about this document should be emailed directly to
        the MPLS working group mailing list at mpls@uu.net."
 
   DESCRIPTION
       "Copyright (C) 2005 The Internet Society.  This version of
        this MIB module is part of RFC 4220; see the RFC
        itself for full legal notices.
 
        This MIB module contains managed object definitions for
        MPLS traffic engineering links as defined in
        'Link Bundling in MPLS Traffic Engineering (TE)'."
 
   -- Revision history.
   REVISION
       "200510110000Z"  -- 11 October 2005
   DESCRIPTION
       "Initial version published as RFC 4220."
   ::= { transmission 200 }
 
-- Textual Conventions
 
TeLinkBandwidth ::= TEXTUAL-CONVENTION
   STATUS       current
   DESCRIPTION
       "This type is used to represent link bandwidth in bps.  This
        value is represented using a 4 octet IEEE floating point
        format [IEEE].  The floating point representation is not
        used to represent fractional value but rather to allow
        specification of large numbers that cannot be expressed
        with 32-bit integers."
   REFERENCE
       "IEEE Standard for Binary Floating-Point Arithmetic,
        Standard 754-1985"
   SYNTAX       OCTET STRING (SIZE(4))
 
TeLinkPriority ::= TEXTUAL-CONVENTION
   DISPLAY-HINT "d"
   STATUS       current
   DESCRIPTION
       "This type is used to represent a priority.  Each connection
        is assigned a priority.  This priority is used when
        accounting for bandwidth on TE links or component
        links, for resource allocation and for rerouting purposes.
        Value 0 is the highest priority.  Value 7 is the lowest
        priority."
 
 
 
   SYNTAX       Unsigned32 (0..7)
 
TeLinkProtection ::= TEXTUAL-CONVENTION
   STATUS       current
   DESCRIPTION
       "Link protection."
   SYNTAX       INTEGER {
                    primary(1),
                    secondary(2)
                }
 
TeLinkSwitchingCapability ::= TEXTUAL-CONVENTION
   STATUS       current
   DESCRIPTION
       "Switching capability as specified in the 'OSPF Extensions in
        Support of Generalized Multi-Protocol Label Switching
        (GMPLS)' document.  The values specified in this document
        are not contiguous."
   SYNTAX       INTEGER {
                    packetSwitch1(1),
                    packetSwitch2(2),
                    packetSwitch3(3),
                    packetSwitch4(4),
                    layer2Switch(51),
                    tdm(100),
                    lambdaSwitch(150),
                    fiberSwitch(200)
                }
 
TeLinkEncodingType ::= TEXTUAL-CONVENTION
   STATUS       current
   DESCRIPTION
       "Link encoding type as specified in 'Generalized
        Multi-Protocol Label Switching (GMPLS) Signaling
        Functional Description' document.  The values
        specified in this document are not contiguous."
   SYNTAX       INTEGER {
                    packet(1),
                    ethernet(2),
                    ansiEtsiPdh(3),
                    sdhItuSonetAnsi(5),
                    digitalWrapper(7),
                    lambda(8),
                    fiber(9),
                    fiberChannel(11)
                }
 
TeLinkSonetSdhIndication ::= TEXTUAL-CONVENTION
 
 
 
   STATUS       current
   DESCRIPTION
       "This convention is used to indicate whether the interface
        supports Standard or Arbitrary SONET/SDH.  To simplify the
        mapping process, the values used in this textual convention
        match the values specified in the interface switching
        capability specific information field, i.e., 0 for Standard
        SONET/SDH and 1 for Arbitrary SONET/SDH."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   SYNTAX       INTEGER {
                    standard(0),
                    arbitrary(1)
                }
 
-- Top level components of this MIB module
 
-- Notifications
teLinkNotifications OBJECT IDENTIFIER ::= { teLinkStdMIB 0 }
-- Tables, Scalars
teLinkObjects       OBJECT IDENTIFIER ::= { teLinkStdMIB 1 }
-- Conformance
teLinkConformance   OBJECT IDENTIFIER ::= { teLinkStdMIB 2 }
 
-- TE Link Table
 
teLinkTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF TeLinkEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies the grouping of component links into
        TE links and the grouping of TE links into bundled links."
   ::= { teLinkObjects 1 }
 
teLinkEntry OBJECT-TYPE
   SYNTAX        TeLinkEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table exists for each ifEntry with an
        ifType of teLink(200), i.e., for every TE link.  An ifEntry
        in the ifTable must exist before a teLinkEntry is created
        with the corresponding ifIndex.  If a TE link entry in the
        ifTable is destroyed, then so is the corresponding entry
        in the teLinkTable.  The administrative and operational
        status values are controlled from the ifEntry."
 
 
 
   INDEX         { ifIndex }
   ::= { teLinkTable 1 }
 
TeLinkEntry ::= SEQUENCE {
  teLinkAddressType                 InetAddressType,
  teLinkLocalIpAddr                 InetAddress,
  teLinkRemoteIpAddr                InetAddress,
  teLinkMetric                      Unsigned32,
  teLinkMaximumReservableBandwidth  TeLinkBandwidth,
  teLinkProtectionType              INTEGER,
  teLinkWorkingPriority             TeLinkPriority,
  teLinkResourceClass               Unsigned32,
  teLinkIncomingIfId                Integer32,
  teLinkOutgoingIfId                InterfaceIndexOrZero,
  teLinkRowStatus                   RowStatus,
  teLinkStorageType                 StorageType
}
 
teLinkAddressType OBJECT-TYPE
   SYNTAX        InetAddressType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The type of Internet address for the TE link."
   ::= { teLinkEntry 1 }
 
teLinkLocalIpAddr OBJECT-TYPE
   SYNTAX        InetAddress
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The local Internet address for numbered links.  The type of
        this address is determined by the value of the
        teLinkAddressType object.
 
        For IPv4 and IPv6 numbered links, this object represents the
        local IP address associated with the TE link.  For an
        unnumbered link, the local address is of type unknown, this
        object is set to the zero length string, and the
        teLinkOutgoingIfId object then identifies the unnumbered
        address.
 
        If the TE link is a Forwarding Adjacency (FA), the local
        IP address is set to the head-end address of the FA-LSP.
 
        If ipAddrTable is implemented, this object must have the
        same value as the ipAdEntAddr object that belongs to the
        row in ipAddrTable where ipAdEntIfIndex is equal to
 
 
 
        ifIndex."
   ::= { teLinkEntry 2 }
 
teLinkRemoteIpAddr OBJECT-TYPE
   SYNTAX        InetAddress
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The remote Internet address for numbered links.  The type of
        this address is determined by the value of the
        teLinkAddressType object.
 
        The remote IP address associated with the TE link (IPv4 and
        IPv6 numbered links).  For an unnumbered link, the remote
        address is of type unknown, this object is set to the
        zero length string, and the teLinkIncomingIfId object then
        identifies the unnumbered address.
 
        If the TE link is a Forwarding Adjacency, the remote IP
        address is set to the tail-end address of the FA-LSP."
   ::= { teLinkEntry 3 }
 
teLinkMetric OBJECT-TYPE
   SYNTAX        Unsigned32
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The traffic engineering metric for the TE link is
        derived from its component links.  All component links
        within the TE link must have the same traffic
        engineering metric."
   REFERENCE
       "Link Bundling in MPLS Traffic Engineering (TE), RFC 4201"
   ::= { teLinkEntry 4 }
 
teLinkMaximumReservableBandwidth OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum reservable bandwidth on
        the TE link.  This is the union of the maximum reservable
        bandwidth of all the component links within the
        TE link that can be used to carry live traffic."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
 
 
 
   ::= { teLinkEntry 5 }
 
teLinkProtectionType OBJECT-TYPE
   SYNTAX        INTEGER {
                     extraTraffic(1),
                     unprotected(2),
                     shared(3),
                     dedicated1For1(4),
                     dedicated1Plus1(5),
                     enhanced(6)
                 }
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the link protection type of the
        TE link.  Descriptions of the different protection types can
        be found in the 'Routing Extensions in Support of
        Generalized Multi-Protocol Label Switching (GMPLS)'
        document."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203 and
        Routing Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4202"
   ::= { teLinkEntry 6 }
 
teLinkWorkingPriority OBJECT-TYPE
   SYNTAX        TeLinkPriority
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This object represents a priority value such that a new
        connection with a higher priority, i.e., numerically lower
        than this value, is guaranteed to be setup on a primary
        link and not on a secondary link."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkEntry 7 }
 
teLinkResourceClass OBJECT-TYPE
   SYNTAX        Unsigned32
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the TE link resource class.
        The resource class is a 32 bit bitfield.  The resource class
        for a link bundle is derived from the resource class of its
 
 
 
        TE links.  All TE links within a link bundle must have the
        same resource class.  Encoding of the resource class is
        described in the 'Traffic Engineering (TE) Extensions to
        OSPF Version 2' document."
   REFERENCE
       "Link Bundling in MPLS Traffic Engineering (TE), RFC 4201
        and Traffic Engineering (TE) Extensions to OSPF Version 2,
        RFC 3630"
   ::= { teLinkEntry 8 }
 
teLinkIncomingIfId OBJECT-TYPE
   SYNTAX        Integer32 (0..2147483647)
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "For unnumbered links, the incoming interface is set to the
        outgoing interface identifier chosen by the neighboring LSR
        for the reverse link corresponding to this TE link.  If the
        link is numbered, the value of this object is 0 and the
        address is stored in the teLinkRemoteIpAddr instead."
   REFERENCE
       "Link Bundling in MPLS Traffic Engineering (TE), RFC 4201"
   ::= { teLinkEntry 9 }
 
teLinkOutgoingIfId OBJECT-TYPE
   SYNTAX        InterfaceIndexOrZero
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "If the link is unnumbered, the outgoing interface identifier
        is set to the outgoing interface identifier chosen for the
        TE link by the advertising LSR.  If the link is numbered, the
        value of this object is 0 and the address is stored in the
        teLinkLocalIpAddr instead."
   REFERENCE
       "Link Bundling in MPLS Traffic Engineering (TE), RFC 4201"
   ::= { teLinkEntry 10 }
 
teLinkRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table.  None of the writable objects in
        a row can be changed if status is active(1)."
   ::= { teLinkEntry 11 }
 
 
 
 
teLinkStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The storage type for this conceptual row in the
        teLinkTable.  Conceptual rows having the value
        'permanent' need not allow write-access to any
        columnar object in the row."
   ::= { teLinkEntry 12 }
 
-- End of teLinkTable
 
 
-- TE Link Descriptor Table
 
teLinkDescriptorTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF TeLinkDescriptorEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies the interface switching capability
        descriptors associated with the TE links."
   ::= { teLinkObjects 2 }
 
teLinkDescriptorEntry OBJECT-TYPE
   SYNTAX        TeLinkDescriptorEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table is created for every TE link interface
        switching capability descriptor.  An ifEntry in the ifTable
        must exist before a teLinkDescriptorEntry using the same
        ifIndex is created.  ifType of ifEntry must be teLink(200).
        If a TE link entry in the ifTable is destroyed, then so are
        all of the entries in the teLinkDescriptorTable that use the
        ifIndex of this TE link."
   INDEX         { ifIndex, teLinkDescriptorId }
   ::= { teLinkDescriptorTable 1 }
 
TeLinkDescriptorEntry ::= SEQUENCE {
  teLinkDescriptorId               Unsigned32,
  teLinkDescrSwitchingCapability   TeLinkSwitchingCapability,
  teLinkDescrEncodingType          TeLinkEncodingType,
  teLinkDescrMinLspBandwidth       TeLinkBandwidth,
  teLinkDescrMaxLspBandwidthPrio0  TeLinkBandwidth,
  teLinkDescrMaxLspBandwidthPrio1  TeLinkBandwidth,
  teLinkDescrMaxLspBandwidthPrio2  TeLinkBandwidth,
 
 
 
  teLinkDescrMaxLspBandwidthPrio3  TeLinkBandwidth,
  teLinkDescrMaxLspBandwidthPrio4  TeLinkBandwidth,
  teLinkDescrMaxLspBandwidthPrio5  TeLinkBandwidth,
  teLinkDescrMaxLspBandwidthPrio6  TeLinkBandwidth,
  teLinkDescrMaxLspBandwidthPrio7  TeLinkBandwidth,
  teLinkDescrInterfaceMtu          Unsigned32,
  teLinkDescrIndication            TeLinkSonetSdhIndication,
  teLinkDescrRowStatus             RowStatus,
  teLinkDescrStorageType           StorageType
}
 
teLinkDescriptorId OBJECT-TYPE
   SYNTAX        Unsigned32 (1..4294967295)
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This object specifies the link descriptor identifier."
   ::= { teLinkDescriptorEntry 1 }
 
teLinkDescrSwitchingCapability OBJECT-TYPE
   SYNTAX        TeLinkSwitchingCapability
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies interface switching capability of
        the TE link, which is derived from its component links."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 2 }
 
teLinkDescrEncodingType OBJECT-TYPE
   SYNTAX        TeLinkEncodingType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the TE link encoding type."
   REFERENCE
       "Generalized Multi-Protocol Label Switching (GMPLS)
        Signaling Functional Description, RFC 3471"
   ::= { teLinkDescriptorEntry 3 }
 
teLinkDescrMinLspBandwidth OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
 
 
 
       "This attribute specifies the minimum LSP bandwidth on
        the TE link.  This is derived from the union of the
        minimum LSP bandwidth of all the component links
        associated with the TE link that can be used to carry
        live traffic."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 4 }
 
teLinkDescrMaxLspBandwidthPrio0 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 0 on the TE link.  This is the union of the maximum
        LSP bandwidth at priority 0 of all the component links within
        the TE link that can be used to carry live traffic."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 5 }
 
teLinkDescrMaxLspBandwidthPrio1 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 1 on the TE link.  This is the union of the maximum
        LSP bandwidth at priority 1 of all the component links within
        the TE link that can be used to carry live traffic."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 6 }
 
teLinkDescrMaxLspBandwidthPrio2 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 2 on the TE link.  This is the union of the maximum
 
 
 
        LSP bandwidth at priority 2 of all the component links within
        the TE link that can be used to carry live traffic."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 7 }
 
teLinkDescrMaxLspBandwidthPrio3 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 3 on the TE link.  This is the union of the maximum
        LSP bandwidth at priority 3 of all the component links within
        the TE link that can be used to carry live traffic."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 8 }
 
teLinkDescrMaxLspBandwidthPrio4 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 4 on the TE link.  This is the union of the maximum
        LSP bandwidth at priority 4 of all the component links within
        the TE link that can be used to carry live traffic."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 9 }
 
teLinkDescrMaxLspBandwidthPrio5 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 5 on the TE link.  This is the union of the maximum
        LSP bandwidth at priority 5 of all the component links within
        the TE link that can be used to carry live traffic."
   REFERENCE
 
 
 
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 10 }
 
teLinkDescrMaxLspBandwidthPrio6 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 6 on the TE link.  This is the union of the maximum
        LSP bandwidth at priority 6 of all the component links within
        the TE link that can be used to carry live traffic."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 11 }
 
teLinkDescrMaxLspBandwidthPrio7 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 7 on the TE link.  This is the union of the maximum
        LSP bandwidth at priority 7 of all the component links within
        the TE link that can be used to carry live traffic."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 12 }
 
teLinkDescrInterfaceMtu OBJECT-TYPE
   SYNTAX        Unsigned32 (1..65535)
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the interface MTU for the TE
        link descriptor."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 13 }
 
teLinkDescrIndication OBJECT-TYPE
   SYNTAX        TeLinkSonetSdhIndication
 
 
 
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies whether this interface supports
        Standard or Arbitrary SONET/SDH."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkDescriptorEntry 14 }
 
teLinkDescrRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table.  No read-create object
        can be changed if teLinkDescrRowStatus is in the active(1)
        state."
   ::= { teLinkDescriptorEntry 15 }
 
teLinkDescrStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The storage type for this conceptual row in the
        teLinkDescriptorTable.  Conceptual rows having the value
        'permanent' need not allow write-access to any
        columnar object in the row."
   ::= { teLinkDescriptorEntry 16 }
 
-- End of teLinkDescriptorTable
 
 
-- TE Link Shared Risk Link Group Table
 
teLinkSrlgTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF TeLinkSrlgEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies the SRLGs associated with TE links."
   ::= { teLinkObjects 3 }
 
teLinkSrlgEntry OBJECT-TYPE
   SYNTAX        TeLinkSrlgEntry
   MAX-ACCESS    not-accessible
 
 
 
   STATUS        current
   DESCRIPTION
       "An entry in this table contains information about an
        SRLG associated with a TE link.
        An ifEntry in the ifTable must exist before a
        teLinkSrlgEntry using the same ifIndex is created.
        The ifType of ifEntry must be teLink(200).
        If a TE link entry in the ifTable is destroyed, then so
        are all of the entries in the teLinkSrlgTable that use the
        ifIndex of this TE link."
   INDEX         { ifIndex, teLinkSrlg }
   ::= { teLinkSrlgTable 1 }
 
TeLinkSrlgEntry ::= SEQUENCE {
  teLinkSrlg            Unsigned32,
  teLinkSrlgRowStatus   RowStatus,
  teLinkSrlgStorageType StorageType
}
 
teLinkSrlg OBJECT-TYPE
   SYNTAX        Unsigned32 (0..4294967295)
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This identifies an SRLG supported by the TE link.  An SRLG is
        identified with a 32-bit number that is unique within an IGP
        domain.  Zero is a valid SRLG number."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { teLinkSrlgEntry 1 }
 
teLinkSrlgRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table.  No read-create object can
        be modified if teLinkSrlgRowStatus is active(1)."
   ::= { teLinkSrlgEntry 2 }
 
teLinkSrlgStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The storage type for this conceptual row in the
 
 
 
        teLinkSrlgTable.  Conceptual rows having the value
        'permanent' need not allow write-access to any
        columnar object in the row."
   ::= { teLinkSrlgEntry 3 }
 
-- End of teLinkSrlgTable
 
 
-- TE Link Bandwidth Table
 
teLinkBandwidthTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF TeLinkBandwidthEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies the priority-based bandwidth table
        for TE links."
   ::= { teLinkObjects 4 }
 
teLinkBandwidthEntry OBJECT-TYPE
   SYNTAX        TeLinkBandwidthEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table contains information about
        the priority-based bandwidth of TE links.  An ifEntry in the
        ifTable must exist before a teLinkBandwidthEntry using the
        same ifIndex is created.  The ifType of ifEntry must be
        teLink(200).  If a TE link entry in the ifTable is destroyed,
        then so are all of the entries in the teLinkBandwidthTable
        that use the ifIndex of this TE link."
   INDEX         { ifIndex, teLinkBandwidthPriority }
   ::= { teLinkBandwidthTable 1 }
 
TeLinkBandwidthEntry ::= SEQUENCE {
  teLinkBandwidthPriority    TeLinkPriority,
  teLinkBandwidthUnreserved  TeLinkBandwidth,
  teLinkBandwidthRowStatus   RowStatus,
  teLinkBandwidthStorageType StorageType
}
 
teLinkBandwidthPriority OBJECT-TYPE
   SYNTAX        TeLinkPriority
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This attribute specifies the priority.  A value of 0 is valid
        as specified in the 'Traffic Engineering (TE) Extensions to
 
 
 
        OSPF Version 2' document."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203 and
        Traffic Engineering (TE) Extensions to OSPF Version 2,
        RFC 3630"
   ::= { teLinkBandwidthEntry 1 }
 
teLinkBandwidthUnreserved OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This attribute specifies the TE link unreserved
        bandwidth at priority p.  It is the sum of the unreserved
        bandwidths at priority p of all component links associated
        with the TE link (excluding all links that are strictly
        used as protecting links)."
   REFERENCE
       "Link Bundling in MPLS Traffic Engineering (TE), RFC 4201"
   ::= { teLinkBandwidthEntry 2 }
 
teLinkBandwidthRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table.  No read-create object
        can be modified when teLinkBandwidthRowStatus is active(1)."
   ::= { teLinkBandwidthEntry 3 }
 
teLinkBandwidthStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The storage type for this conceptual row in the
        teLinkBandwidthTable.  Conceptual rows having the value
        'permanent' need not allow write-access to any
        columnar object in the row."
   ::= { teLinkBandwidthEntry 4 }
 
-- End of teLinkBandwidthTable
 
 
-- Component Link Table
 
 
 
componentLinkTable  OBJECT-TYPE
   SYNTAX        SEQUENCE OF ComponentLinkEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies the component link parameters."
   ::= { teLinkObjects 5 }
 
componentLinkEntry  OBJECT-TYPE
   SYNTAX        ComponentLinkEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table exists for each ifEntry that
        represents a component link.  An ifEntry must exist in
        the ifTable before a componentLinkEntry is created with
        the corresponding ifIndex.  ifEntry's ifType can be
        of any interface type that has been defined for TE Link
        interworking.  Examples include ATM, Frame Relay, Ethernet,
        etc.  If an entry representing a component link is destroyed
        in the ifTable, then so is the corresponding entry in the
        componentLinkTable.  The administrative and operational
        status values are controlled from the ifEntry."
   INDEX         { ifIndex }
   ::= { componentLinkTable 1 }
 
ComponentLinkEntry ::= SEQUENCE {
  componentLinkMaxResBandwidth     TeLinkBandwidth,
  componentLinkPreferredProtection TeLinkProtection,
  componentLinkCurrentProtection   TeLinkProtection,
  componentLinkRowStatus           RowStatus,
  componentLinkStorageType         StorageType
}
 
componentLinkMaxResBandwidth OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum reservable bandwidth on
        the component link."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkEntry 1 }
 
componentLinkPreferredProtection OBJECT-TYPE
 
 
 
   SYNTAX        TeLinkProtection
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies whether this component link is
        a primary or secondary entity."
   ::= { componentLinkEntry 2 }
 
componentLinkCurrentProtection OBJECT-TYPE
   SYNTAX        TeLinkProtection
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This attribute specifies whether this component link is
        currently used as primary or secondary link."
   ::= { componentLinkEntry 3 }
 
componentLinkRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table.  No read-create object
        can be modified when componentLinkRowStatus is active(1)."
   ::= { componentLinkEntry 4 }
 
componentLinkStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The storage type for this conceptual row in the
        componentLinkTable.  Conceptual rows having the value
        'permanent' need not allow write-access to any
        columnar object in the row."
   ::= { componentLinkEntry 5 }
 
-- End of componentLinkTable
 
 
-- Component Link Descriptor Table
 
componentLinkDescriptorTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF ComponentLinkDescriptorEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
 
 
 
       "This table specifies the interface switching capability
        descriptors associated with the component links."
   ::= { teLinkObjects 6 }
 
componentLinkDescriptorEntry OBJECT-TYPE
   SYNTAX        ComponentLinkDescriptorEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table is created for every component link
        descriptor.  An ifEntry in the ifTable must exist before a
        componentLinkDescriptorEntry using the same ifIndex is
        created.  ifEntry's ifType can be of any interface type that
        has been defined for TE Link interworking.  Examples include
        ATM, Frame Relay, Ethernet, etc.  If a component link entry
        in the ifTable is destroyed, then so are all entries in the
        componentLinkDescriptorTable that use the ifIndex of this
        component link."
   INDEX         { ifIndex, componentLinkDescrId }
   ::= { componentLinkDescriptorTable 1 }
 
ComponentLinkDescriptorEntry ::= SEQUENCE {
  componentLinkDescrId                    Unsigned32,
  componentLinkDescrSwitchingCapability   TeLinkSwitchingCapability,
  componentLinkDescrEncodingType          TeLinkEncodingType,
  componentLinkDescrMinLspBandwidth       TeLinkBandwidth,
  componentLinkDescrMaxLspBandwidthPrio0  TeLinkBandwidth,
  componentLinkDescrMaxLspBandwidthPrio1  TeLinkBandwidth,
  componentLinkDescrMaxLspBandwidthPrio2  TeLinkBandwidth,
  componentLinkDescrMaxLspBandwidthPrio3  TeLinkBandwidth,
  componentLinkDescrMaxLspBandwidthPrio4  TeLinkBandwidth,
  componentLinkDescrMaxLspBandwidthPrio5  TeLinkBandwidth,
  componentLinkDescrMaxLspBandwidthPrio6  TeLinkBandwidth,
  componentLinkDescrMaxLspBandwidthPrio7  TeLinkBandwidth,
  componentLinkDescrInterfaceMtu          Unsigned32,
  componentLinkDescrIndication            TeLinkSonetSdhIndication,
  componentLinkDescrRowStatus             RowStatus,
  componentLinkDescrStorageType           StorageType
}
 
componentLinkDescrId OBJECT-TYPE
   SYNTAX        Unsigned32 (1..4294967295)
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This object specifies the link descriptor identifier."
   ::= { componentLinkDescriptorEntry 1 }
 
 
 
 
componentLinkDescrSwitchingCapability OBJECT-TYPE
   SYNTAX        TeLinkSwitchingCapability
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies link multiplexing capabilities of
        the component link."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 2 }
 
componentLinkDescrEncodingType OBJECT-TYPE
   SYNTAX        TeLinkEncodingType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the component link encoding type."
   REFERENCE
       "Generalized Multi-Protocol Label Switching (GMPLS) Signaling
        Functional Description, RFC 3471"
   ::= { componentLinkDescriptorEntry 3 }
 
componentLinkDescrMinLspBandwidth OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the minimum LSP bandwidth on
        the component link."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 4 }
 
componentLinkDescrMaxLspBandwidthPrio0 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 0 on the component link."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 5 }
 
 
 
componentLinkDescrMaxLspBandwidthPrio1 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 1 on the component link."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 6 }
 
componentLinkDescrMaxLspBandwidthPrio2 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 2 on the component link."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 7 }
 
componentLinkDescrMaxLspBandwidthPrio3 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 3 on the component link."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 8 }
 
componentLinkDescrMaxLspBandwidthPrio4 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 4 on the component link."
   REFERENCE
 
 
 
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 9 }
 
componentLinkDescrMaxLspBandwidthPrio5 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "thousand bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 5 on the component link."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 10 }
 
componentLinkDescrMaxLspBandwidthPrio6 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 6 on the component link."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 11 }
 
componentLinkDescrMaxLspBandwidthPrio7 OBJECT-TYPE
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies the maximum LSP bandwidth at
        priority 7 on the component link."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 12 }
 
componentLinkDescrInterfaceMtu OBJECT-TYPE
   SYNTAX        Unsigned32 (1..65535)
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
 
 
 
       "This attribute specifies the interface MTU for the component
        link descriptor."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 13 }
 
componentLinkDescrIndication OBJECT-TYPE
   SYNTAX        TeLinkSonetSdhIndication
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This attribute specifies whether this interface supports
        Standard or Arbitrary SONET/SDH."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkDescriptorEntry 14 }
 
componentLinkDescrRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table.  No read-create object
        can be modified when componentLinkDescrRowStatus
        is active(1)."
   ::= { componentLinkDescriptorEntry 15 }
 
componentLinkDescrStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The storage type for this conceptual row in the
        componentLinkDescriptorTable.  Conceptual rows
        having the value 'permanent' need not allow write-access
        to any columnar object in the row."
   ::= { componentLinkDescriptorEntry 16 }
 
-- End of componentLinkDescriptorTable
 
 
-- Component Link Bandwidth Table
 
componentLinkBandwidthTable OBJECT-TYPE
   SYNTAX        SEQUENCE OF ComponentLinkBandwidthEntry
 
 
 
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This table specifies the priority-based bandwidth
        for component links."
   ::= { teLinkObjects 7 }
 
componentLinkBandwidthEntry OBJECT-TYPE
   SYNTAX        ComponentLinkBandwidthEntry
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "An entry in this table contains information about
        the priority-based bandwidth on component links.
        An ifEntry in the ifTable must exist before a
        componentLinkBandwidthEntry using the same ifIndex is
        created.  ifEntry's ifType can be of any interface type that
        has been defined for TE Link interworking.  Examples
        include ATM, Frame Relay, Ethernet, etc.  If a component link
        entry in the ifTable is destroyed, then so are all entries
        in the componentLinkBandwidthTable that use the ifIndex of
        this component link."
   INDEX         { ifIndex, componentLinkBandwidthPriority }
   ::= { componentLinkBandwidthTable 1 }
 
ComponentLinkBandwidthEntry ::= SEQUENCE {
  componentLinkBandwidthPriority    TeLinkPriority,
  componentLinkBandwidthUnreserved  TeLinkBandwidth,
  componentLinkBandwidthRowStatus   RowStatus,
  componentLinkBandwidthStorageType StorageType
}
 
componentLinkBandwidthPriority OBJECT-TYPE
   SYNTAX        TeLinkPriority
   MAX-ACCESS    not-accessible
   STATUS        current
   DESCRIPTION
       "This attribute specifies the priority.  A value of 0 is valid
        as specified in the 'Traffic Engineering (TE) Extensions to
         OSPF Version 2' document."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203 and
        Traffic Engineering (TE) Extensions to OSPF Version 2,
        RFC 3630"
   ::= { componentLinkBandwidthEntry 1 }
 
componentLinkBandwidthUnreserved OBJECT-TYPE
 
 
 
   SYNTAX        TeLinkBandwidth
   UNITS         "bps"
   MAX-ACCESS    read-only
   STATUS        current
   DESCRIPTION
       "This attribute specifies the component link unreserved
        bandwidth at priority p."
   REFERENCE
       "OSPF Extensions in Support of Generalized Multi-Protocol
        Label Switching (GMPLS), RFC 4203"
   ::= { componentLinkBandwidthEntry 2 }
 
componentLinkBandwidthRowStatus OBJECT-TYPE
   SYNTAX        RowStatus
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "This variable is used to create, modify, and/or
        delete a row in this table.  No read-create object can
        be modified when componentLinkBandwidthRowStatus is
        active(1)."
   ::= { componentLinkBandwidthEntry 3 }
 
componentLinkBandwidthStorageType OBJECT-TYPE
   SYNTAX        StorageType
   MAX-ACCESS    read-create
   STATUS        current
   DESCRIPTION
       "The storage type for this conceptual row in the
        componentLinkBandwidthTable.  Conceptual rows
        having the value 'permanent' need not allow write-access
        to any columnar object in the row."
   ::= { componentLinkBandwidthEntry 4 }
 
-- End of componentLinkBandwidthTable
 
 
-- Module compliance
 
teLinkCompliances
   OBJECT IDENTIFIER ::= { teLinkConformance 1 }
 
teLinkGroups
   OBJECT IDENTIFIER ::= { teLinkConformance 2 }
 
teLinkModuleFullCompliance MODULE-COMPLIANCE
   STATUS current
   DESCRIPTION
 
 
 
       "Compliance statement for agents that support read-create
        so that both configuration and monitoring of TE links can
        be accomplished via this MIB module."
   MODULE -- this module
 
      MANDATORY-GROUPS    { teLinkGroup,
                            teLinkBandwidthGroup,
                            componentLinkBandwidthGroup }
 
      GROUP teLinkSrlgGroup
      DESCRIPTION
          "This group is mandatory for GMPLS enabled devices."
 
      GROUP teLinkPscGroup
      DESCRIPTION
          "This group is mandatory for devices that support the
           packet switching capability."
 
      GROUP teLinkTdmGroup
      DESCRIPTION
          "This group is mandatory for devices that support the TDM
           switching capability."
 
      -- teLinkTable
 
      OBJECT      teLinkAddressType
      SYNTAX      INTEGER { unknown(0), ipv4(1), ipv6(2) }
      DESCRIPTION
          "Only ipv4(1) and ipv6(2) address types need to be
           supported for numbered links.  For unnumbered links, the
           unknown(0) address type needs to be supported."
 
      OBJECT      teLinkLocalIpAddr
      SYNTAX      InetAddress (SIZE(0|4|16))
      DESCRIPTION
          "Size of TE link IP address depends on type of TE link.
           TE link IP address size is zero if the link is unnumbered,
           four if the link IP address is IPv4, and sixteen if the
           link IP address is IPv6."
 
      OBJECT      teLinkRemoteIpAddr
      SYNTAX      InetAddress (SIZE(0|4|16))
      DESCRIPTION
          "Size of TE link IP address depends on type of TE link.
           TE link IP address size is zero if the link is unnumbered,
           four if the link IP address is IPv4, and sixteen if the
           link IP address is IPv6."
 
 
 
 
      OBJECT      teLinkRowStatus
      SYNTAX      RowStatus { active(1), notInService(2) }
      WRITE-SYNTAX RowStatus { active(1), notInService(2),
                               createAndGo(4), destroy(6) }
      DESCRIPTION
          "Support for notReady(3) and createAndWait(5) is
           not required."
 
      -- teLinkDescriptorTable
 
      OBJECT      teLinkDescrRowStatus
      SYNTAX      RowStatus { active(1), notInService(2) }
      WRITE-SYNTAX RowStatus { active(1), notInService(2),
                               createAndGo(4), destroy(6) }
      DESCRIPTION
          "Support for notReady(3) and createAndWait(5) is
           not required."
 
      -- teLinkSrlgTable
 
      OBJECT      teLinkSrlgRowStatus
      SYNTAX      RowStatus { active(1), notInService(2) }
      WRITE-SYNTAX RowStatus { active(1), notInService(2),
                               createAndGo(4), destroy(6) }
      DESCRIPTION
          "Support for notReady(3) and createAndWait(5) is
           not required."
 
      -- teLinkBandwidthTable
 
      OBJECT      teLinkBandwidthRowStatus
      SYNTAX      RowStatus { active(1), notInService(2) }
      WRITE-SYNTAX RowStatus { active(1), notInService(2),
                               createAndGo(4), destroy(6) }
      DESCRIPTION
          "Support for notReady(3) and createAndWait(5) is
           not required."
 
      -- componentLinkTable
 
      OBJECT      componentLinkRowStatus
      SYNTAX      RowStatus { active(1), notInService(2) }
      WRITE-SYNTAX RowStatus { active(1), notInService(2),
                               createAndGo(4), destroy(6) }
      DESCRIPTION
          "Support for notReady(3) and createAndWait(5) is
           not required."
 
 
 
 
      -- componentLinkDescriptorTable
 
      OBJECT      componentLinkDescrRowStatus
      SYNTAX      RowStatus { active(1), notInService(2) }
      WRITE-SYNTAX RowStatus { active(1), notInService(2),
                               createAndGo(4), destroy(6) }
      DESCRIPTION
          "Support for notReady(3) and createAndWait(5) is
           not required."
 
      -- componentLinkBandwidthTable
 
      OBJECT      componentLinkBandwidthRowStatus
      SYNTAX      RowStatus { active(1), notInService(2) }
      WRITE-SYNTAX RowStatus { active(1), notInService(2),
                               createAndGo(4), destroy(6) }
      DESCRIPTION
          "Support for notReady(3) and createAndWait(5) is
           not required."
 
   ::= { teLinkCompliances 1 }
 
teLinkModuleReadOnlyCompliance MODULE-COMPLIANCE
   STATUS current
   DESCRIPTION
       "Compliance statement for agents that support the
        monitoring of the TE link MIB module."
   MODULE -- this module
 
      MANDATORY-GROUPS    { teLinkGroup,
                            teLinkBandwidthGroup,
                            componentLinkBandwidthGroup }
 
      GROUP teLinkSrlgGroup
      DESCRIPTION
          "This group is mandatory for GMPLS enabled devices."
 
      GROUP teLinkPscGroup
      DESCRIPTION
          "This group is mandatory for devices that support the
           packet switching capability."
 
      GROUP teLinkTdmGroup
      DESCRIPTION
          "This group is mandatory for devices that support the TDM
           switching capability."
 
      -- teLinkTable
 
 
 
      OBJECT      teLinkAddressType
      SYNTAX      INTEGER { unknown(0), ipv4(1), ipv6(2) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Only ipv4(1) and ipv6(2) address types need to be
           supported for numbered links.  For unnumbered links, the
           unknown(0) address type needs to be supported."
 
      OBJECT      teLinkLocalIpAddr
      SYNTAX      InetAddress (SIZE(0|4|16))
      MIN-ACCESS  read-only
      DESCRIPTION
          "Size of TE link IP address depends on type of TE link.
           TE link IP address size is zero if the link is unnumbered,
           four if the link IP address is IPv4, and sixteen if the
           link IP address is IPv6."
 
      OBJECT      teLinkRemoteIpAddr
      SYNTAX      InetAddress (SIZE(0|4|16))
      MIN-ACCESS  read-only
      DESCRIPTION
          "Size of TE link IP address depends on type of TE link.
           TE link IP address size is zero if the link is unnumbered,
           four if the link IP address is IPv4, and sixteen if the
           link IP address is IPv6."
 
      OBJECT      teLinkProtectionType
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkWorkingPriority
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkRowStatus
      SYNTAX      RowStatus { active(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required and active(1) is the
           only status that needs to be supported."
 
      OBJECT      teLinkStorageType
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
 
 
 
      -- teLinkDescriptorTable
 
      OBJECT      teLinkDescrSwitchingCapability
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkDescrEncodingType
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkDescrMinLspBandwidth
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkDescrMaxLspBandwidthPrio0
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkDescrMaxLspBandwidthPrio1
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkDescrMaxLspBandwidthPrio2
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkDescrMaxLspBandwidthPrio3
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkDescrMaxLspBandwidthPrio4
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkDescrMaxLspBandwidthPrio5
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkDescrMaxLspBandwidthPrio6
 
 
 
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkDescrMaxLspBandwidthPrio7
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      teLinkDescrRowStatus
      SYNTAX      RowStatus { active(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required and active(1) is the
           only status that needs to be supported."
 
      OBJECT      teLinkDescrStorageType
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      -- teLinkSrlgTable
 
      OBJECT      teLinkSrlgRowStatus
      SYNTAX      RowStatus { active(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required and active(1) is the
           only status that needs to be supported."
 
      OBJECT      teLinkSrlgStorageType
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      -- teLinkBandwidthTable
 
      OBJECT      teLinkBandwidthRowStatus
      SYNTAX      RowStatus { active(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required and active(1) is the
           only status that needs to be supported."
 
      OBJECT      teLinkBandwidthStorageType
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
 
 
      -- componentLinkTable
 
      OBJECT      componentLinkMaxResBandwidth
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkPreferredProtection
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkRowStatus
      SYNTAX      RowStatus { active(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required and active(1) is the
           only status that needs to be supported."
 
      OBJECT      componentLinkStorageType
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      -- componentLinkDescriptorTable
 
      OBJECT      componentLinkDescrSwitchingCapability
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrEncodingType
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrMinLspBandwidth
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrMaxLspBandwidthPrio0
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrMaxLspBandwidthPrio1
      MIN-ACCESS  read-only
 
 
 
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrMaxLspBandwidthPrio2
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrMaxLspBandwidthPrio3
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrMaxLspBandwidthPrio4
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrMaxLspBandwidthPrio5
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrMaxLspBandwidthPrio6
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrMaxLspBandwidthPrio7
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrInterfaceMtu
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrIndication
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      OBJECT      componentLinkDescrRowStatus
      SYNTAX      RowStatus { active(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required and active(1) is the
 
 
 
           only status that needs to be supported."
 
      OBJECT      componentLinkDescrStorageType
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
      -- componentLinkBandwidthTable
 
      OBJECT      componentLinkBandwidthRowStatus
      SYNTAX      RowStatus { active(1) }
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required and active(1) is the
           only status that needs to be supported."
 
      OBJECT      componentLinkBandwidthStorageType
      MIN-ACCESS  read-only
      DESCRIPTION
          "Write access is not required."
 
   ::= { teLinkCompliances 2 }
 
-- Units of conformance
 
teLinkGroup OBJECT-GROUP
   OBJECTS { teLinkAddressType,
             teLinkLocalIpAddr,
             teLinkRemoteIpAddr,
             teLinkMetric,
             teLinkProtectionType,
             teLinkWorkingPriority,
             teLinkResourceClass,
             teLinkIncomingIfId,
             teLinkOutgoingIfId,
             teLinkRowStatus,
             teLinkStorageType,
             teLinkDescrSwitchingCapability,
             teLinkDescrEncodingType,
             teLinkDescrRowStatus,
             teLinkDescrStorageType,
             componentLinkPreferredProtection,
             componentLinkCurrentProtection,
             componentLinkRowStatus,
             componentLinkStorageType,
             componentLinkDescrSwitchingCapability,
             componentLinkDescrEncodingType,
             componentLinkDescrRowStatus,
 
 
 
             componentLinkDescrStorageType
           }
 
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for the management of
           resources associated with TE links."
   ::= { teLinkGroups 1 }
 
teLinkSrlgGroup OBJECT-GROUP
   OBJECTS { teLinkSrlgRowStatus,
             teLinkSrlgStorageType
           }
 
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for the management of
           SRLG resources associated with TE links."
   ::= { teLinkGroups 2 }
 
teLinkBandwidthGroup OBJECT-GROUP
   OBJECTS { teLinkMaximumReservableBandwidth,
             teLinkDescrMaxLspBandwidthPrio0,
             teLinkDescrMaxLspBandwidthPrio1,
             teLinkDescrMaxLspBandwidthPrio2,
             teLinkDescrMaxLspBandwidthPrio3,
             teLinkDescrMaxLspBandwidthPrio4,
             teLinkDescrMaxLspBandwidthPrio5,
             teLinkDescrMaxLspBandwidthPrio6,
             teLinkDescrMaxLspBandwidthPrio7,
             teLinkBandwidthUnreserved,
             teLinkBandwidthRowStatus,
             teLinkBandwidthStorageType
           }
 
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for the management of
           the bandwidth resources associated with TE links and
           component links."
   ::= { teLinkGroups 3 }
 
componentLinkBandwidthGroup OBJECT-GROUP
   OBJECTS { componentLinkMaxResBandwidth,
             componentLinkDescrMaxLspBandwidthPrio0,
             componentLinkDescrMaxLspBandwidthPrio1,
             componentLinkDescrMaxLspBandwidthPrio2,
             componentLinkDescrMaxLspBandwidthPrio3,
 
 
 
             componentLinkDescrMaxLspBandwidthPrio4,
             componentLinkDescrMaxLspBandwidthPrio5,
             componentLinkDescrMaxLspBandwidthPrio6,
             componentLinkDescrMaxLspBandwidthPrio7,
             componentLinkBandwidthUnreserved,
             componentLinkBandwidthRowStatus,
             componentLinkBandwidthStorageType
           }
 
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for the management of the
           bandwidth parameters associated with component links."
   ::= { teLinkGroups 4 }
 
teLinkPscGroup OBJECT-GROUP
   OBJECTS { teLinkDescrMinLspBandwidth,
             teLinkDescrInterfaceMtu,
             componentLinkDescrMinLspBandwidth,
             componentLinkDescrInterfaceMtu
           }
 
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for devices that are
           packet switch capable."
   ::= { teLinkGroups 5 }
 
teLinkTdmGroup OBJECT-GROUP
   OBJECTS { teLinkDescrMinLspBandwidth,
             teLinkDescrIndication,
             componentLinkDescrMinLspBandwidth,
             componentLinkDescrIndication
           }
 
   STATUS  current
   DESCRIPTION
          "Collection of objects needed for devices that are
           TDM switching capable."
   ::= { teLinkGroups 6 }
 
-- End of TE-LINK-STD-MIB
END