SSPM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Counter32, Integer32, Unsigned32 FROM SNMPv2-SMI --[RFC2578] TEXTUAL-CONVENTION, StorageType, TruthValue, RowStatus FROM SNMPv2-TC --[RFC2579] MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF --[RFC2578, -- RFC2579, -- RFC2580] OwnerString, rmon FROM RMON-MIB --[RFC2819] InetAddressType, InetAddress FROM INET-ADDRESS-MIB --[RFC3291] InterfaceIndexOrZero FROM IF-MIB --[RFC2863] AppLocalIndex FROM APM-MIB --[RFC3729] Utf8String FROM SYSAPPL-MIB; --[RFC2287] sspmMIB MODULE-IDENTITY LAST-UPDATED "200507280000Z" -- July 28, 2005 ORGANIZATION "IETF RMON MIB working group" CONTACT-INFO " Carl W. Kalbfleisch Consultant E-mail: ietf@kalbfleisch.us Working group mailing list: rmonmib@ietf.org To subscribe send email to rmonmib-request@ietf.org" DESCRIPTION "This SSPM MIB module is applicable to probes implementing Synthetic Source for Performance Monitoring functions. Copyright (C) The Internet Society (2005). This version of this MIB module is part of RFC 4149; see the RFC itself for full legal notices." -- revision history REVISION "200507280000Z" -- July 28, 2005 DESCRIPTION "The original version of this MIB module, was published as RFC4149." ::= { rmon 28 } -- -- Object Identifier Assignments -- sspmMIBObjects OBJECT IDENTIFIER ::= { sspmMIB 1 } sspmMIBNotifications OBJECT IDENTIFIER ::= { sspmMIB 2 } sspmMIBConformance OBJECT IDENTIFIER ::= { sspmMIB 3 } -- -- Textual Conventions -- SspmMicroSeconds ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "A unit of time with resolution of MicroSeconds." SYNTAX Unsigned32 SspmClockSource ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "An indication of the source of the clock as defined by the NTP specification RFC1305 [RFC1305] definition of stratum: Stratum (sys.stratum, peer.stratum, pkt.stratum): This is an integer indicating the stratum of the local clock, with values defined as follows: 0 unspecified 1 primary reference (e.g., calibrated atomic clock, radio clock) 2-255 secondary reference (via NTP)." REFERENCE "RFC1305." SYNTAX Integer32 (0..255) SspmClockMaxSkew ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current -- UNITS "Seconds" DESCRIPTION "An indication of the accuracy of the clock as defined by RFC1305. This variable indicates the maximum offset error due to skew of the local clock over the time interval 86400 seconds, in seconds." REFERENCE "RFC1305." SYNTAX Integer32 (1..65535) -- -- sspmGeneral -- sspmGeneral OBJECT IDENTIFIER ::= { sspmMIBObjects 1 } sspmGeneralClockResolution OBJECT-TYPE SYNTAX SspmMicroSeconds MAX-ACCESS read-only STATUS current -- UNITS Microseconds DESCRIPTION "A read-only variable indicating the resolution of the measurements possible by this device." ::= { sspmGeneral 1 } sspmGeneralClockMaxSkew OBJECT-TYPE SYNTAX SspmClockMaxSkew MAX-ACCESS read-only STATUS current -- UNITS Seconds DESCRIPTION "A read-only variable indicating the maximum offset error due to skew of the local clock over the time interval 86400 seconds, in seconds." ::= { sspmGeneral 2 } sspmGeneralClockSource OBJECT-TYPE SYNTAX SspmClockSource MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only variable indicating the source of the clock. This is provided to allow a user to determine how accurate the timing mechanism is compared with other devices. This is needed for the coordination of time values between probes for one-way measurements." ::= { sspmGeneral 3 } sspmGeneralMinFrequency OBJECT-TYPE SYNTAX SspmMicroSeconds MAX-ACCESS read-only -- units MicroSeconds STATUS current DESCRIPTION "A read-only variable that indicates the devices' capability for the minimum supported sspmSourceFrequency. If sspmSourceFrequency is set to a value lower than the value reported by this attribute, then the set of sspmSourceFrequency will fail with an inconsistent value error." ::= { sspmGeneral 4 } -- -- sspmCapabilities -- -- Describes the capabilities of the SSPM device. -- sspmCapabilitiesTable OBJECT-TYPE SYNTAX SEQUENCE OF SspmCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of SSPM capabilities." ::= { sspmGeneral 5 } sspmCapabilitiesEntry OBJECT-TYPE SYNTAX SspmCapabilitiesEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Details about a particular SSPM capability." INDEX { sspmCapabilitiesInstance } ::= { sspmCapabilitiesTable 1 } SspmCapabilitiesEntry ::= SEQUENCE { sspmCapabilitiesInstance AppLocalIndex } sspmCapabilitiesInstance OBJECT-TYPE SYNTAX AppLocalIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether SSPM configuration of the corresponding AppLocalIndex is supported by this device. Generally, entries in this table are only made by the device when the configuration of the measurement is available." ::= { sspmCapabilitiesEntry 1 } -- -- sspmSource -- -- Contains the details of the source of the -- Synthetic Sources for Performance Monitoring algorithms. -- This information is split into two tables. The first defines -- profiles that can be applied to specific sources in the -- control table. -- sspmSource OBJECT IDENTIFIER ::= { sspmMIBObjects 2 } -- -- sspmSourceProfileTable -- Defines template profiles for measurements. -- sspmSourceProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF SspmSourceProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of SSPM Source Profiles configured." ::= { sspmSource 1 } sspmSourceProfileEntry OBJECT-TYPE SYNTAX SspmSourceProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Details about a particular SSPM Source Profile configuration. Entries must exist in this table in order to be referenced by rows in the sspmSourceControlTable." INDEX { sspmSourceProfileInstance } ::= { sspmSourceProfileTable 1 } SspmSourceProfileEntry ::= SEQUENCE { sspmSourceProfileInstance Unsigned32, sspmSourceProfileType AppLocalIndex, sspmSourceProfilePacketSize Unsigned32, sspmSourceProfilePacketFillType INTEGER, sspmSourceProfilePacketFillValue OCTET STRING, sspmSourceProfileTOS Integer32, sspmSourceProfileFlowLabel Integer32, sspmSourceProfileLooseSrcRteFill OCTET STRING, sspmSourceProfileLooseSrcRteLen Integer32, sspmSourceProfileTTL Integer32, sspmSourceProfileNoFrag TruthValue, sspmSourceProfile8021Tagging Integer32, sspmSourceProfileUsername Utf8String, sspmSourceProfilePassword Utf8String, sspmSourceProfileParameter OCTET STRING, sspmSourceProfileOwner OwnerString, sspmSourceProfileStorageType StorageType, sspmSourceProfileStatus RowStatus } sspmSourceProfileInstance OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary index." ::= { sspmSourceProfileEntry 1 } sspmSourceProfileType OBJECT-TYPE SYNTAX AppLocalIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The AppLocalIndex value that uniquely identifies the measurement per the APM-MIB. In order to create a row in this table, there must be a corresponding row in the sspmCapabilitiesTable. When attempting to set this object, if no corresponding row exists in the sspmCapabilitiesTable, then the agent should return a 'badValue' error." ::= { sspmSourceProfileEntry 2} sspmSourceProfilePacketSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The size of packet to be transmitted in bytes. The size accounts for all data within the IPv4 or IPv6 payloads, excluding the IP headers, IP header options and link-level protocol headers. If the size is set smaller than the minimum allowed packet size or greater than the maximum allowed packet size, then the set should fail, and the agent should return a 'badValue' error." ::= { sspmSourceProfileEntry 3 } sspmSourceProfilePacketFillType OBJECT-TYPE SYNTAX INTEGER { random (1), pattern (2), url(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates how the packet is filled. 'random' indicates that the packet contains random data patterns. This is probe and implementation dependent. 'pattern' indicates that the pattern defined in the sspmSourceProfilePacketFillValue attribute is used to fill the packet. 'url' indicates that the value of sspmSourceProfilePacketFillValue should contain a URL. The contents of the document at that URL are retrieved when sspmSourceStatus becomes active and utilized in the packet. If the attempt to access that URL fails, then the row status is set to 'notReady', and the set should fail with 'inconsistentValue'. This value must contain a dereferencable URL of the type 'http:', 'https:', or 'ftp:' only." ::= { sspmSourceProfileEntry 4 } sspmSourceProfilePacketFillValue OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..255)) MAX-ACCESS read-create STATUS current DESCRIPTION "The string value with which to fill the packet. If sspmSourceProfilePacketFillType is set to 'pattern', then this pattern is repeated until the packet is sspmSourcePacketSize in bytes. Note that if the length of the octet string specified for this value does not divide evenly into the packet size, then an incomplete last copy of this data may be copied into the packet. If the value of sspmSourceProfilePacketFillType is set to 'random', then this attribute is unused. If the value of the sspmSourceProfilePacketFillType is set to 'url', then the URL specified in this attribute is retrieved and used by the probe. In the case of a URL, this value must contain a dereferencable URL of the type 'http:', 'https:', or 'ftp:' only." ::= { sspmSourceProfileEntry 5 } sspmSourceProfileTOS OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Represents the TOS field in the IP packet header. The value of this object defaults to zero if not set." DEFVAL { 0 } ::= { sspmSourceProfileEntry 6 } sspmSourceProfileFlowLabel OBJECT-TYPE SYNTAX Integer32 (0..1048575) -- 20-bit range (0 to 0xfffff) MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to specify the Flow Label in a IPv6 packet (RFC 2460) to force special handling by the IPv6 routers; e.g., non-default quality-of-service handling. This object is meaningful only when the object sspmSourceDestAddressType is IPv6(2). The value of this object defaults to zero if not set." DEFVAL { 0 } ::= { sspmSourceProfileEntry 7 } sspmSourceProfileLooseSrcRteFill OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..240)) MAX-ACCESS read-create STATUS current DESCRIPTION "In the event that the test should run over a specific route, the intent is to force the route using the Loose Source Route option in IPv4 [RFC791] and IPv6 [RFC2460]. This object contains a series of IP addresses along the path that would be put into the loose source route option in the IP header. The IPv4 addresses are to be listed as 32-bit address values, and the IPv6 addresses are to be listed as a string of 128-bit addresses. The maximum length allowed within the IPv4 source route option is 63 addresses. To simply account for IPv6 addresses as well, the maximum length of the octet string is 240. This allows up to 60 IPv4 addresses or up to 15 IPv6 addresses in the string." ::= { sspmSourceProfileEntry 8 } sspmSourceProfileLooseSrcRteLen OBJECT-TYPE SYNTAX Integer32(0..240) MAX-ACCESS read-create STATUS current DESCRIPTION "In the event that the test should run over a specific route, the intent is to force the route. This attribute specifies the length of data to be copied from the sspmSourceProfileLooseSrcRteFill into the route data fields of the loose source route options in the IPv4 or IPv6 headers." ::= { sspmSourceProfileEntry 9 } sspmSourceProfileTTL OBJECT-TYPE SYNTAX Integer32(1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "If non-zero, this specifies the value to place into the TTL field on transmission." ::= { sspmSourceProfileEntry 10 } sspmSourceProfileNoFrag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "When true, the 'Don't Fragment Bit' should be set on the packet header." ::= { sspmSourceProfileEntry 11 } sspmSourceProfile8021Tagging OBJECT-TYPE SYNTAX Integer32 (-1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "IEEE 802.1Q tagging used in IEEE 802.1D bridged environments. A value of -1 indicates that the packets are untagged. A value of 0 to 65535 is the value of the tag to be inserted in the tagged packets. Note that according to IEEE 802.1Q, VLAN-ID tags with a value of 4095 shall not be transmitted on the wire. As the VLAN-ID is encoded in the 12 least significant bits on the tag, values that translate in a binary representation of all 1's in the last 12 bits SHALL NOT be configured. In this case, the set should fail, and return an error-status of 'inconsistentValue'." ::= { sspmSourceProfileEntry 12 } sspmSourceProfileUsername OBJECT-TYPE SYNTAX Utf8String MAX-ACCESS read-create STATUS current DESCRIPTION "An optional username used by the application protocol." ::= { sspmSourceProfileEntry 13 } sspmSourceProfilePassword OBJECT-TYPE SYNTAX Utf8String MAX-ACCESS read-create STATUS current DESCRIPTION "An optional password used by the application protocol." ::= { sspmSourceProfileEntry 14 } sspmSourceProfileParameter OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..65535)) MAX-ACCESS read-create STATUS current DESCRIPTION "An optional parameter used by the application protocol. For DNS, this would be the hostname or IP. For HTTP, this would be the URL. For nntp, this would be the news group. For TCP, this would be the port number. For SMTP, this would be the recipient (and could assume the message is predefined)." ::= { sspmSourceProfileEntry 15 } sspmSourceProfileOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "Name of the management station/application that set up the profile." ::= { sspmSourceProfileEntry 16 } sspmSourceProfileStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type of this sspmSourceProfileEntry. If the value of this object is 'permanent', no objects in this row need to be writable." ::= { sspmSourceProfileEntry 17 } sspmSourceProfileStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this profile. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Once this object is set to active(1), no objects in the sspmSourceProfileTable can be changed." ::= { sspmSourceProfileEntry 18 } -- -- sspmSourceControlTable -- Defines specific measurement instances based on template -- profiles in the sspmSourceProfileTable which must be -- pre-configured. -- sspmSourceControlTable OBJECT-TYPE SYNTAX SEQUENCE OF SspmSourceControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of SSPM measurements configured." ::= { sspmSource 2 } sspmSourceControlEntry OBJECT-TYPE SYNTAX SspmSourceControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Details about a particular SSPM configuration." INDEX { sspmSourceControlInstance } ::= { sspmSourceControlTable 1 } SspmSourceControlEntry ::= SEQUENCE { sspmSourceControlInstance Unsigned32, sspmSourceControlProfile Integer32, sspmSourceControlSrc InterfaceIndexOrZero, sspmSourceControlDestAddrType InetAddressType, sspmSourceControlDestAddr InetAddress, sspmSourceControlEnabled TruthValue, sspmSourceControlTimeOut SspmMicroSeconds, sspmSourceControlSamplingDist INTEGER, sspmSourceControlFrequency SspmMicroSeconds, sspmSourceControlFirstSeqNum Unsigned32, sspmSourceControlLastSeqNum Unsigned32, sspmSourceControlOwner OwnerString, sspmSourceControlStorageType StorageType, sspmSourceControlStatus RowStatus } sspmSourceControlInstance OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary index." ::= { sspmSourceControlEntry 1 } sspmSourceControlProfile OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "A pointer to the profile (sspmSourceProfileEntry) that this control entry uses to define the test being performed." ::= { sspmSourceControlEntry 2 } sspmSourceControlSrc OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "The ifIndex where the packet should originate from the probe (if it matters). A value of zero indicates that it does not matter and that the device decides." ::= { sspmSourceControlEntry 3 } sspmSourceControlDestAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of Internet address by which the destination is accessed." ::= { sspmSourceControlEntry 4 } sspmSourceControlDestAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The Internet address for the destination. The formatting of this object is controlled by the sspmSourceControlDestAddrType object above. When this object contains a DNS name, then the name is resolved to an address each time measurement is to be made. Further, the agent should not cache this address, but instead should perform the resolution prior to each measurement." ::= { sspmSourceControlEntry 5 } sspmSourceControlEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "When set to 'true', this test is enabled. When set to 'false', it is disabled." ::= { sspmSourceControlEntry 6 } sspmSourceControlTimeOut OBJECT-TYPE SYNTAX SspmMicroSeconds MAX-ACCESS read-create STATUS current DESCRIPTION "Timeout value for the measurement response. If no response is received in the time specified, then the test fails." ::= { sspmSourceControlEntry 7 } sspmSourceControlSamplingDist OBJECT-TYPE SYNTAX INTEGER { deterministic(1), poisson(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "When this attribute is set to 'deterministic', then packets are generated at with a fixed inter-packet injection time specified by sspmSourceFrequency. When this attribute is set to 'Poisson', then packets are generated with inter-packet injection times sampled from an exponential distribution with the single distributional parameter determined by the inverse frequency)." ::= { sspmSourceControlEntry 8 } sspmSourceControlFrequency OBJECT-TYPE SYNTAX SspmMicroSeconds MAX-ACCESS read-create STATUS current DESCRIPTION "The inverse of this value is the rate at which packets are generated. Refer to sspmSourceSamplingDistribution. If the value set is less than the value of sspmGeneralMinFrequency, then the set will fail with an error-status of 'inconsistentValue'." ::= { sspmSourceControlEntry 9 } sspmSourceControlFirstSeqNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The first sequence number of packets to be transmitted." ::= { sspmSourceControlEntry 10 } sspmSourceControlLastSeqNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The last sequence number transmitted. This value is updated by the agent after packet generation." ::= { sspmSourceControlEntry 11 } sspmSourceControlOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "Name of the management station/application that set up the test." ::= { sspmSourceControlEntry 12 } sspmSourceControlStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type of this sspmSourceControlEntry. If the value of this object is 'permanent', no objects in this row need to be writable." ::= { sspmSourceControlEntry 13 } sspmSourceControlStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this source control entry. An entry may not exist in the active state unless all objects in the entry have an appropriate value. When this attribute has the value of 'active', none of the read-write or read-create attributes in this table may be modified, with the exception of sspmSourceControlEnabled." ::= { sspmSourceControlEntry 14 } -- -- sspmSinkTable -- -- Contains attributes for configuration of Synthetic -- Sources for Performance Monitoring sinks, i.e., -- sinks for receipt of one-way delay measurements. -- sspmSink OBJECT IDENTIFIER ::= { sspmMIBObjects 5 } sspmSinkTable OBJECT-TYPE SYNTAX SEQUENCE OF SspmSinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table configuring the sink for measurements." ::= { sspmSink 1 } sspmSinkEntry OBJECT-TYPE SYNTAX SspmSinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The details of a particular sink entry. If the measurement is a round-trip type, then the sink entry will be on the same probe as the corresponding sspmSourceEntry. If the measurement is a one-way, type then the sink entry will be on a different probe." INDEX { sspmSinkInstance } ::= { sspmSinkTable 1} SspmSinkEntry ::= SEQUENCE { sspmSinkInstance Unsigned32, sspmSinkType AppLocalIndex, sspmSinkSourceAddressType InetAddressType, sspmSinkSourceAddress InetAddress, sspmSinkExpectedRate SspmMicroSeconds, sspmSinkEnable TruthValue, sspmSinkExpectedFirstSequenceNum Unsigned32, sspmSinkLastSequenceNumber Unsigned32, sspmSinkLastSequenceInvalid Counter32, sspmSinkStorageType StorageType, sspmSinkStatus RowStatus } sspmSinkInstance OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index. When the measurement is for a round-trip measurement, then this table entry is on the same probe as the corresponding sspmSourceEntry, and the value of this attribute should correspond to the value of sspmSourceInstance. Management applications configuring sinks for one-way measurements could define some scheme whereby the sspmSinkInstance is unique across all probes. Note that the unique key to this entry is also constructed with sspmSinkType, sspmSinkSourceAddressType, and sspmSinkSourceAddress. To make the implementation simpler, those other attributes are not included in the index but uniqueness is still needed to receive all the packets." ::= { sspmSinkEntry 1 } sspmSinkType OBJECT-TYPE SYNTAX AppLocalIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The AppLocalIndex value that uniquely identifies the measurement per the APM-MIB. In order to create a row in this table, there must be a corresponding row in the sspmCapabilitiesTable. If there is no corresponding row in the sspmCapabilitiestable, then the agent will return an error-status of 'inconsistentValue'." ::= { sspmSinkEntry 2} sspmSinkSourceAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The type of Internet address of the source." ::= { sspmSinkEntry 3 } sspmSinkSourceAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The Internet address of the source. The formatting of this object is controlled by the sspmSinkSourceAddressType object above. This object should be set only to a valid device address that has been administratively configured into the device. If a set attempts to set this object to an address that does not belong (i.e., is not administratively configured into the device), the set should fail, and the agent should return a error-status of 'inconsistentValue'." ::= { sspmSinkEntry 4 } sspmSinkExpectedRate OBJECT-TYPE SYNTAX SspmMicroSeconds MAX-ACCESS read-create STATUS current DESCRIPTION "The expected rate at which packets will arrive." ::= { sspmSinkEntry 5 } sspmSinkEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates if the sink is enabled or not." ::= { sspmSinkEntry 6 } sspmSinkExpectedFirstSequenceNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The expected first sequence number of packets. This is used by the sink to determine if packets were lost at the initiation of the test." ::= { sspmSinkEntry 7 } sspmSinkLastSequenceNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The last sequence number received." ::= { sspmSinkEntry 8 } sspmSinkLastSequenceInvalid OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets that arrived whose sequence number was not one plus the value of sspmSinkLastSequenceNumber." ::= { sspmSinkEntry 9 } sspmSinkStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type of this sspmSinkEntry. If the value of this object is 'permanent', no objects in this row need to be writable." ::= { sspmSinkEntry 10 } sspmSinkStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this conceptual row. An entry may not exist in the active state unless all objects in the entry have an appropriate value. Once this object is set to active(1), no objects with MAX-ACCESS of read-create in the sspmSinkTable can be changed." ::= { sspmSinkEntry 11 } -- -- Notifications -- -- -- Conformance information -- sspmCompliances OBJECT IDENTIFIER ::= { sspmMIBConformance 1 } sspmGroups OBJECT IDENTIFIER ::= { sspmMIBConformance 2 } -- Compliance Statements sspmGeneralCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "A general compliance that allows all things to be optional." MODULE -- this module MANDATORY-GROUPS { sspmGeneralGroup } GROUP sspmSourceGroup DESCRIPTION "The SSPM Source Group is optional." GROUP sspmSinkGroup DESCRIPTION "The SSPM Sink Group is optional." GROUP sspmUserPassGroup DESCRIPTION "The SSPM User Pass Group is optional." ::= { sspmCompliances 1 } -- -- SSPM Source Compliance -- sspmSourceFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "A source compliance. Use this compliance when implementing a traffic-source-only device. This is useful for implementing devices that probe other devices for intrusive application monitoring. It is also useful for implementing the source of one-way tests used with a sink-only device." MODULE -- this module MANDATORY-GROUPS { sspmGeneralGroup, sspmSourceGroup } GROUP sspmUserPassGroup DESCRIPTION "The SSPM User Pass Group is optional." ::= { sspmCompliances 2 } -- -- SSPM Sink Compliance -- sspmSinkFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "A sink-only compliance. Use this compliance when implementing a sink-only device. This is useful for devices to receive one-way measurements." MODULE -- this module MANDATORY-GROUPS { sspmGeneralGroup, sspmSinkGroup } ::= { sspmCompliances 3 } -- -- Groups -- sspmGeneralGroup OBJECT-GROUP OBJECTS { sspmGeneralClockResolution, sspmGeneralClockMaxSkew, sspmGeneralClockSource, sspmGeneralMinFrequency, sspmCapabilitiesInstance } STATUS current DESCRIPTION "The objects in the SSPM General Group." ::= { sspmGroups 1 } sspmSourceGroup OBJECT-GROUP OBJECTS { sspmSourceProfileType, sspmSourceProfilePacketSize, sspmSourceProfilePacketFillType, sspmSourceProfilePacketFillValue, sspmSourceProfileTOS, sspmSourceProfileFlowLabel, sspmSourceProfileLooseSrcRteFill, sspmSourceProfileLooseSrcRteLen, sspmSourceProfileTTL, sspmSourceProfileNoFrag, sspmSourceProfile8021Tagging, sspmSourceProfileUsername, sspmSourceProfilePassword, sspmSourceProfileParameter, sspmSourceProfileOwner, sspmSourceProfileStorageType, sspmSourceProfileStatus, sspmSourceControlProfile, sspmSourceControlSrc, sspmSourceControlDestAddrType, sspmSourceControlDestAddr, sspmSourceControlEnabled, sspmSourceControlTimeOut, sspmSourceControlSamplingDist, sspmSourceControlFrequency, sspmSourceControlFirstSeqNum, sspmSourceControlLastSeqNum, sspmSourceControlOwner, sspmSourceControlStorageType, sspmSourceControlStatus } STATUS current DESCRIPTION "The objects in the SSPM Source Group." ::= { sspmGroups 2 } sspmUserPassGroup OBJECT-GROUP OBJECTS { sspmSourceProfileUsername, sspmSourceProfilePassword } STATUS current DESCRIPTION "The objects in the SSPM Username and password group." ::= { sspmGroups 3 } sspmSinkGroup OBJECT-GROUP OBJECTS { sspmSinkType, sspmSinkSourceAddressType, sspmSinkSourceAddress, sspmSinkExpectedRate, sspmSinkEnable, sspmSinkExpectedFirstSequenceNum, sspmSinkLastSequenceNumber, sspmSinkLastSequenceInvalid, sspmSinkStorageType, sspmSinkStatus } STATUS current DESCRIPTION "The objects in the SSPM Sink Group." ::= { sspmGroups 4 } END