RBRIDGE-MIB DEFINITIONS ::= BEGIN -- ---------------------------------------------------------- -- -- MIB for RBRIDGE devices, also known as TRILL Switches -- ---------------------------------------------------------- -- IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Counter64, Unsigned32, mib-2 FROM SNMPv2-SMI -- RFC2578 TEXTUAL-CONVENTION, TruthValue, MacAddress, RowStatus FROM SNMPv2-TC -- RFC2579 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC2580 VlanId, PortList FROM Q-BRIDGE-MIB -- RFC4363 InetAddress, InetAddressType FROM INET-ADDRESS-MIB -- RFC4001 BridgeId FROM BRIDGE-MIB -- RFC4188 InterfaceIndex FROM IF-MIB -- RFC2863 ; rbridgeMIB MODULE-IDENTITY LAST-UPDATED "201301070000Z" ORGANIZATION "IETF TRILL Working Group" CONTACT-INFO "http://datatracker.ietf.org/wg/trill/charter/ Email: trill@ietf.org Anil Rijhsinghani Hewlett-Packard Tel: +1 508 323 1251 Email: anil@charter.net Kate Zebrose HW Embedded Tel: +1 617 840 9673 Email: zebrose@alum.mit.edu" DESCRIPTION "The RBridge MIB module for managing switches that support the TRILL protocol." REVISION "201301070000Z" DESCRIPTION "Initial version, published as RFC 6850. Copyright (c) 2013 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info)." ::= { mib-2 214 } -- ---------------------------------------------------------- -- -- Subtrees in the RBridge MIB -- ---------------------------------------------------------- -- rbridgeNotifications OBJECT IDENTIFIER ::= { rbridgeMIB 0 } rbridgeObjects OBJECT IDENTIFIER ::= { rbridgeMIB 1 } rbridgeConformance OBJECT IDENTIFIER ::= { rbridgeMIB 2 } rbridgeBase OBJECT IDENTIFIER ::= { rbridgeObjects 1 } rbridgeFdb OBJECT IDENTIFIER ::= { rbridgeObjects 2 } rbridgeVlan OBJECT IDENTIFIER ::= { rbridgeObjects 3 } rbridgeEsadi OBJECT IDENTIFIER ::= { rbridgeObjects 4 } rbridgeCounter OBJECT IDENTIFIER ::= { rbridgeObjects 5 } rbridgeSnooping OBJECT IDENTIFIER ::= { rbridgeObjects 6 } rbridgeDtree OBJECT IDENTIFIER ::= { rbridgeObjects 7 } rbridgeTrill OBJECT IDENTIFIER ::= { rbridgeObjects 8 } -- ---------------------------------------------------------- -- -- Type Definitions -- ---------------------------------------------------------- -- RbridgeAddress ::= TEXTUAL-CONVENTION DISPLAY-HINT "1x:" STATUS current DESCRIPTION "The Media Access Control (MAC) address used by an RBridge port. This may match the RBridge IS-IS SystemID." SYNTAX OCTET STRING (SIZE (6)) RbridgeNickname ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The 16-bit identifier used in TRILL as an abbreviation for the RBridge's 48-bit IS-IS System ID. The value 0 means a nickname is not specified, the values 0xFFC0 through 0xFFFE are reserved for future allocation, and the value 0xFFFF is permanently reserved." REFERENCE "RFC 6325, Section 3.7" SYNTAX Unsigned32 (0..65471) -- -- the rbridgeBase subtree -- -- Implementation of the rbridgeBase subtree is mandatory for all -- RBridges. -- rbridgeBaseTrillVersion OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum TRILL version number that this RBridge supports." REFERENCE "RFC 6325, Section 3.2" ::= { rbridgeBase 1 } rbridgeBaseNumPorts OBJECT-TYPE SYNTAX Unsigned32 UNITS "ports" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ports controlled by this RBridge." REFERENCE "RFC 6325, Section 2.6.1" ::= { rbridgeBase 2 } rbridgeBaseForwardDelay OBJECT-TYPE SYNTAX Unsigned32 (4..30) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Modified aging time for address entries after an appointed forwarder change. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.8.3" ::= { rbridgeBase 3 } rbridgeBaseUniMultipathEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The enabled status of unicast TRILL multipathing. It is enabled when true. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Appendix C" ::= { rbridgeBase 4 } rbridgeBaseMultiMultipathEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "The enabled status of multi-destination TRILL multipathing. It is enabled when true. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Appendix C" ::= { rbridgeBase 5 } rbridgeBaseAcceptEncapNonadj OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Accept TRILL-encapsulated frames from a neighbor with which this RBridge does not have an IS-IS adjacency, when the value of this object is 'true'. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.6.2" ::= { rbridgeBase 6 } rbridgeBaseNicknameNumber OBJECT-TYPE SYNTAX Unsigned32 (1..256) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of nicknames this RBridge should acquire. These can be acquired dynamically or configured statically. This value represents the maximum number of entries in rbridgeBaseNicknameTable. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 3.7.3" ::= { rbridgeBase 7 } -- ---------------------------------------------------------- -- -- The RBridge Base Nickname Table -- ---------------------------------------------------------- -- rbridgeBaseNicknameTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeBaseNicknameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about nicknames configured by an operator or learned dynamically by this RBridge." REFERENCE "RFC 6325, Section 3.7" ::= { rbridgeBase 8 } rbridgeBaseNicknameEntry OBJECT-TYPE SYNTAX RbridgeBaseNicknameEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information for each nickname of the RBridge." REFERENCE "RFC 6325, Section 3.7" INDEX { rbridgeBaseNicknameName } ::= { rbridgeBaseNicknameTable 1 } RbridgeBaseNicknameEntry ::= SEQUENCE { rbridgeBaseNicknameName RbridgeNickname, rbridgeBaseNicknamePriority Unsigned32, rbridgeBaseNicknameDtrPriority Unsigned32, rbridgeBaseNicknameType INTEGER, rbridgeBaseNicknameRowStatus RowStatus } rbridgeBaseNicknameName OBJECT-TYPE SYNTAX RbridgeNickname MAX-ACCESS not-accessible STATUS current DESCRIPTION "Nicknames are 16-bit quantities that act as abbreviations for RBridge's 48-bit IS-IS System ID to achieve a more compact encoding." REFERENCE "RFC 6325, Section 3.7" ::= { rbridgeBaseNicknameEntry 1 } rbridgeBaseNicknamePriority OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "This RBridge's priority to hold this nickname. When the nickname is configured, the default value of this object is 192. When the nickname is configured, the most significant bit (0x80) must be set and the bottom 7 bits have the default value of 0x40, so 0x80 + 0x40 == 0xC0, which is 192 decimal. Additionally, the bottom 7 bits could be configured to a value other than 0x40. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 3.7" DEFVAL { 192 } ::= { rbridgeBaseNicknameEntry 2 } rbridgeBaseNicknameDtrPriority OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The distribution tree root priority for this nickname. The default value of this object is 32768. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.5" DEFVAL { 32768 } ::= { rbridgeBaseNicknameEntry 3 } rbridgeBaseNicknameType OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the status of the entry. The default value is static(1). static(1) - this entry has been configured and will remain after the next reset of the RBridge. dynamic(2) - this entry has been acquired by the RBridge nickname acquisition protocol." REFERENCE "RFC 6325, Section 3.7" DEFVAL { static } ::= { rbridgeBaseNicknameEntry 4 } rbridgeBaseNicknameRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of the entry." ::= { rbridgeBaseNicknameEntry 5 } -- ---------------------------------------------------------- -- -- The RBridge Port Table -- ---------------------------------------------------------- -- rbridgeBasePortTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeBasePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains generic information about every port that is associated with this RBridge." REFERENCE "RFC 6325, Section 5.3" ::= { rbridgeBase 9 } rbridgeBasePortEntry OBJECT-TYPE SYNTAX RbridgeBasePortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information for each port of the bridge." REFERENCE "RFC 6325, Section 5.3" INDEX { rbridgeBasePort } ::= { rbridgeBasePortTable 1 } RbridgeBasePortEntry ::= SEQUENCE { rbridgeBasePort Unsigned32, rbridgeBasePortIfIndex InterfaceIndex, rbridgeBasePortDisable TruthValue, rbridgeBasePortTrunkPort TruthValue, rbridgeBasePortAccessPort TruthValue, rbridgeBasePortP2pHellos TruthValue, rbridgeBasePortState INTEGER, rbridgeBasePortInhibitionTime Unsigned32, rbridgeBasePortDisableLearning TruthValue, rbridgeBasePortDesiredDesigVlan VlanId, rbridgeBasePortDesigVlan VlanId, rbridgeBasePortStpRoot BridgeId, rbridgeBasePortStpRootChanges Counter32, rbridgeBasePortStpWiringCloset BridgeId } rbridgeBasePort OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port number of the port for which this entry contains RBridge management information." REFERENCE "RFC 6325, Section 5.3" ::= { rbridgeBasePortEntry 1 } rbridgeBasePortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the instance of the ifIndex object, defined in the IF-MIB, for the interface corresponding to this port. The RBridge port sits on top of this interface." ::= { rbridgeBasePortEntry 2 } rbridgeBasePortDisable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Disable port bit. When this bit is set (true), all frames received or to be transmitted are discarded, with the possible exception of some layer 2 control frames that may be generated and transmitted or received and processed locally. Default value is 'false'. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.9.1" DEFVAL { false } ::= { rbridgeBasePortEntry 3 } rbridgeBasePortTrunkPort OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "End-station service disable (trunk port) bit. When this bit is set (true), all native frames received on the port and all native frames that would have been sent on the port are discarded. Default value is 'false'. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.9.1" DEFVAL { false } ::= { rbridgeBasePortEntry 4 } rbridgeBasePortAccessPort OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "TRILL traffic disable (access port) bit. If this bit is set, the goal is to avoid sending any TRILL frames, except TRILL-Hello frames, on the port, since it is intended only for native end-station traffic. This ensures that the link is not on the shortest path for any destination. Default value is 'false'. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.9.1" DEFVAL { false } ::= { rbridgeBasePortEntry 5 } rbridgeBasePortP2pHellos OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Use point-to-point (P2P) Hellos bit. If this bit is set, Hellos sent on this port are IS-IS P2P Hellos, not the default TRILL-Hellos. In addition, the IS-IS P2P three-way handshake is used on P2P RBridge links. Default value is 'false'. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.9.1" DEFVAL { false } ::= { rbridgeBasePortEntry 6 } rbridgeBasePortState OBJECT-TYPE SYNTAX INTEGER { uninhibited(1), portInhibited(2), vlanInhibited(3), disabled(4), broken(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port's current state. If the entire port is inhibited, its state is portInhibited(2). If specific VLANs are inhibited, the state is vlanInhibited(3), and rbridgeVlanPortTable will tell which VLANs are inhibited. For ports that are disabled (see rbridgeBasePortDisable), this object will have a value of disabled(4). If the RBridge has detected a port that is malfunctioning, it will place that port into the broken(5) state." REFERENCE "RFC 6325, Section 4.2.4.3" ::= { rbridgeBasePortEntry 7 } rbridgeBasePortInhibitionTime OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "Time in seconds that this RBridge will inhibit forwarding on this port after it observes a spanning tree root bridge change on a link or receives conflicting VLAN forwarder information. The default value is 30. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.2.4.3" DEFVAL { 30 } ::= { rbridgeBasePortEntry 8 } rbridgeBasePortDisableLearning OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Disable learning of MAC addresses seen on this port. To disable learning, the value of this object must be set to 'true'. The default is 'false'. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.8" DEFVAL { false } ::= { rbridgeBasePortEntry 9 } rbridgeBasePortDesiredDesigVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN that a Designated RBridge (DRB) will specify in its TRILL-Hellos as the VLAN to be used by all RBridges on the link for TRILL frames. This VLAN must be enabled on this port. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.4.3" ::= { rbridgeBasePortEntry 10 } rbridgeBasePortDesigVlan OBJECT-TYPE SYNTAX VlanId MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN being used on this link for TRILL frames." REFERENCE "RFC 6325, Section 4.4.3" ::= { rbridgeBasePortEntry 11 } rbridgeBasePortStpRoot OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge identifier of the root of the spanning tree, as learned from a Bridge PDU (BPDU) received on this port. For the Multiple Spanning Tree Protocol (MSTP), this is the root bridge of the Common and Internal Spanning Tree (CIST). If no BPDU has been heard, the value returned is a string of zeros." REFERENCE "RFC 6325, Section 4.2.4.3" ::= { rbridgeBasePortEntry 12 } rbridgeBasePortStpRootChanges OBJECT-TYPE SYNTAX Counter32 UNITS "changes" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a change in the root bridge is seen from spanning tree BPDUs received on this port, indicating a change in bridged LAN topology. Each such change may cause the port to be inhibited for a period of time. This counter should be synchronized with ifCounterDiscontinuityTime. Discontinuities in the value of this counter can occur at re-initialization of the management system." REFERENCE "RFC 6325, Section 4.9.3.2" ::= { rbridgeBasePortEntry 13 } rbridgeBasePortStpWiringCloset OBJECT-TYPE SYNTAX BridgeId MAX-ACCESS read-write STATUS current DESCRIPTION "The Bridge ID to be used as the spanning tree root in BPDUs sent for the Wiring Closet topology solution described in [RFC6325]. Note that the same value of this object must be set on all RBridge ports participating in this solution. The default value is all 0s. A non-zero value configured into this object indicates that this solution is in use. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Appendix A.3.3" ::= { rbridgeBasePortEntry 14 } -- ------------------------------------------------------------- -- RBridge Forwarding Database -- ------------------------------------------------------------- rbridgeConfidenceNative OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The confidence level associated with MAC addresses learned from native frames. This is applicable to all RBridge ports. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.8.1" ::= { rbridgeFdb 1 } rbridgeConfidenceDecap OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The confidence level associated with inner MAC addresses learned after decapsulation of a TRILL data frame. This is applicable to all RBridge ports. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.8.1" ::= { rbridgeFdb 2 } rbridgeConfidenceStatic OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The confidence level associated with MAC addresses that are statically configured. The default value is 255. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.8.2" DEFVAL { 255 } ::= { rbridgeFdb 3 } -- ------------------------------------------------------------- -- Multiple Forwarding Databases for RBridges -- -- This allows for an instance per FdbId, as defined in the -- Bridge MIB. -- -- Each VLAN may have an independent FDB, or multiple VLANs may -- share one. -- ------------------------------------------------------------- rbridgeUniFdbTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeUniFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about unicast entries for which the device has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame." REFERENCE "RFC 6325, Section 4.8" ::= { rbridgeFdb 4 } rbridgeUniFdbEntry OBJECT-TYPE SYNTAX RbridgeUniFdbEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a specific unicast MAC address for which the RBridge has some forwarding and/or filtering information." INDEX { rbridgeFdbId, rbridgeUniFdbAddr } ::= { rbridgeUniFdbTable 1 } RbridgeUniFdbEntry ::= SEQUENCE { rbridgeFdbId Unsigned32, rbridgeUniFdbAddr MacAddress, rbridgeUniFdbPort Unsigned32, rbridgeUniFdbNickname RbridgeNickname, rbridgeUniFdbConfidence Unsigned32, rbridgeUniFdbStatus INTEGER } rbridgeFdbId OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The identity of this Filtering Database." ::= { rbridgeUniFdbEntry 1 } rbridgeUniFdbAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unicast MAC address for which the device has forwarding information." ::= { rbridgeUniFdbEntry 2 } rbridgeUniFdbPort OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Either the value '0', or the RBridge port number of the port on which a frame having a source address equal to the value of the corresponding instance of rbridgeUniFdbAddr has been seen. A value of '0' indicates that the port number has not been learned but that the device does have some information about this MAC address. Implementors are encouraged to assign the port value to this object whenever it is available, even for addresses for which the corresponding value of rbridgeUniFdbStatus is not learned(3)." ::= { rbridgeUniFdbEntry 3 } rbridgeUniFdbNickname OBJECT-TYPE SYNTAX RbridgeNickname MAX-ACCESS read-only STATUS current DESCRIPTION "The RBridge nickname that is placed in the egress nickname field of a TRILL frame sent to this rbridgeFdbAddress in this rbridgeFdbId." REFERENCE "RFC 6325, Section 4.8.1" ::= { rbridgeUniFdbEntry 4 } rbridgeUniFdbConfidence OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The confidence level associated with this entry." REFERENCE "RFC 6325, Section 4.8.1" ::= { rbridgeUniFdbEntry 5 } rbridgeUniFdbStatus OBJECT-TYPE SYNTAX INTEGER { other(1), invalid(2), learned(3), self(4), mgmt(5), esadi(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status of this entry. The meanings of the values are: other(1) - none of the following. invalid(2) - this entry is no longer valid (e.g., it was learned but has since aged out) but has not yet been flushed from the table. learned(3) - the information in this entry was learned and is being used. self(4) - the value of the corresponding instance of rbridgeFdbAddress represents one of the device's addresses. The corresponding instance of rbridgeFdbPort indicates which of the device's ports has this address. mgmt(5) - the value of the corresponding instance of rbridgeFdbAddress was configured by management. esadi(6) - the value of the corresponding instance of rbridgeFdbAddress was learned from ESADI." ::= { rbridgeUniFdbEntry 6 } -- ------------------------------------------------------------- -- RBridge Forwarding Information Base (FIB) -- ------------------------------------------------------------- rbridgeUniFibTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeUniFibEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about nicknames known by the RBridge. If Equal-Cost Multipath (ECMP) is implemented, there are as many entries for a nickname as there are ECMP paths available for it." ::= { rbridgeFdb 5 } rbridgeUniFibEntry OBJECT-TYPE SYNTAX RbridgeUniFibEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information about nicknames known by the RBridge. If ECMP is implemented, there are as many entries as there are ECMP paths available for a given nickname." INDEX { rbridgeUniFibNickname, rbridgeUniFibPort, rbridgeUniFibNextHop } ::= { rbridgeUniFibTable 1 } RbridgeUniFibEntry ::= SEQUENCE { rbridgeUniFibNickname RbridgeNickname, rbridgeUniFibPort Unsigned32, rbridgeUniFibNextHop RbridgeNickname, rbridgeUniFibHopCount Unsigned32 } rbridgeUniFibNickname OBJECT-TYPE SYNTAX RbridgeNickname MAX-ACCESS not-accessible STATUS current DESCRIPTION "An RBridge nickname for which this RBridge has forwarding information." ::= { rbridgeUniFibEntry 1 } rbridgeUniFibPort OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The RBridge port number of the port attached to the next-hop RBridge for the path towards the RBridge whose nickname is specified in this entry." ::= { rbridgeUniFibEntry 2 } rbridgeUniFibNextHop OBJECT-TYPE SYNTAX RbridgeNickname MAX-ACCESS not-accessible STATUS current DESCRIPTION "The nickname of the next-hop RBridge for the path towards the RBridge whose nickname is specified in this entry." ::= { rbridgeUniFibEntry 3 } rbridgeUniFibHopCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The hop count from this ingress RBridge to the egress RBridge whose nickname is specified in rbridgeUniFibNickname." ::= { rbridgeUniFibEntry 4 } rbridgeMultiFibTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeMultiFibEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about egress nicknames used for multi-destination frame forwarding by this RBridge." ::= { rbridgeFdb 6 } rbridgeMultiFibEntry OBJECT-TYPE SYNTAX RbridgeMultiFibEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information about egress nicknames used for multi-destination frame forwarding by this RBridge." INDEX { rbridgeMultiFibNickname } ::= { rbridgeMultiFibTable 1 } RbridgeMultiFibEntry ::= SEQUENCE { rbridgeMultiFibNickname RbridgeNickname, rbridgeMultiFibPorts PortList } rbridgeMultiFibNickname OBJECT-TYPE SYNTAX RbridgeNickname MAX-ACCESS not-accessible STATUS current DESCRIPTION "The nickname of the multicast distribution tree." ::= { rbridgeMultiFibEntry 1 } rbridgeMultiFibPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The list of ports to which a frame destined to this multicast distribution tree is flooded. This may be pruned further based on other forwarding information." ::= { rbridgeMultiFibEntry 2 } -- ---------------------------------------------------------- -- -- The RBridge VLAN Table -- ---------------------------------------------------------- -- rbridgeVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about VLANs on the RBridge." ::= { rbridgeVlan 1 } rbridgeVlanEntry OBJECT-TYPE SYNTAX RbridgeVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information about VLANs on the RBridge." INDEX { rbridgeVlanIndex } ::= { rbridgeVlanTable 1 } RbridgeVlanEntry ::= SEQUENCE { rbridgeVlanIndex Unsigned32, rbridgeVlanForwarderLosts Counter32, rbridgeVlanDisableLearning TruthValue, rbridgeVlanSnooping INTEGER } rbridgeVlanIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4094|4096..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN-ID referring to this VLAN." ::= { rbridgeVlanEntry 1 } rbridgeVlanForwarderLosts OBJECT-TYPE SYNTAX Counter32 UNITS "times" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this RBridge has lost appointed forwarder status for this VLAN on any of its ports. Discontinuities in the value of this counter can occur at re-initialization of the management system." REFERENCE "RFC 6325, Section 4.8.3" ::= { rbridgeVlanEntry 2 } rbridgeVlanDisableLearning OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Disable learning of MAC addresses seen in this VLAN. One application of this may be to restrict learning to ESADI. To disable learning, the value of this object should be set to 'true'. The default is 'false'. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.8" DEFVAL { false } ::= { rbridgeVlanEntry 3 } rbridgeVlanSnooping OBJECT-TYPE SYNTAX INTEGER { notSupported(1), ipv4(2), ipv6(3), ipv4v6(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "IP Multicast Snooping on this VLAN. For RBridges performing both IPv4 and IPv6 IP Multicast Snooping, the value returned is ipv4v6(4)." REFERENCE "RFC 6325, Section 4.7" ::= { rbridgeVlanEntry 4 } -- ---------------------------------------------------------- -- -- The RBridge VLAN Port Table -- ---------------------------------------------------------- -- rbridgeVlanPortTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeVlanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about VLANs on an RBridge port." ::= { rbridgeVlan 2 } rbridgeVlanPortEntry OBJECT-TYPE SYNTAX RbridgeVlanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of information about VLANs on the RBridge port." INDEX { rbridgeBasePort, rbridgeVlanIndex } ::= { rbridgeVlanPortTable 1 } RbridgeVlanPortEntry ::= SEQUENCE { rbridgeVlanPortInhibited TruthValue, rbridgeVlanPortForwarder TruthValue, rbridgeVlanPortAnnouncing TruthValue, rbridgeVlanPortDetectedVlanMapping TruthValue } rbridgeVlanPortInhibited OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This VLAN has been inhibited by the RBridge due to conflicting forwarder information received from another RBridge, when the value of this object is 'true'." REFERENCE "RFC 6325, Section 4.2.4.3" ::= { rbridgeVlanPortEntry 1 } rbridgeVlanPortForwarder OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This RBridge is an appointed forwarder for this VLAN on this port, when the value of this object is 'true'." REFERENCE "RFC 6325, Section 4.2.4.3" ::= { rbridgeVlanPortEntry 2 } rbridgeVlanPortAnnouncing OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "TRILL-Hellos tagged with this VLAN can be sent by this RBridge on this port, when the value of this object is 'true'. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.4.3" DEFVAL { true } ::= { rbridgeVlanPortEntry 3 } rbridgeVlanPortDetectedVlanMapping OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN mapping has been detected on the link attached to this port, when the value of this object is 'true'." REFERENCE "RFC 6325, Section 4.4.5" ::= { rbridgeVlanPortEntry 4 } -- ---------------------------------------------------------- -- -- The RBridge Port Counter Table -- -- These counters supplement counters in the Bridge MIB. -- -- For example, total frames received by a bridge port and total -- frames transmitted by a bridge port are reported in the -- Port In Frames and Port Out Frames counters of the Bridge MIB. -- These total bridge frame counters include native as well as -- encapsulated frames. -- -- As another example, frames discarded due to excessive frame -- size are reported in the port counter MTU Exceeded Discards -- in the Bridge MIB. -- ---------------------------------------------------------- -- rbridgePortCounterTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgePortCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains per-port counters for this RBridge." ::= { rbridgeCounter 1 } rbridgePortCounterEntry OBJECT-TYPE SYNTAX RbridgePortCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Counters for a port on this RBridge." INDEX { rbridgeBasePort } ::= { rbridgePortCounterTable 1 } RbridgePortCounterEntry ::= SEQUENCE { rbridgePortRpfCheckFails Counter32, rbridgePortHopCountExceeds Counter32, rbridgePortOptionDrops Counter32, rbridgePortTrillInFrames Counter64, rbridgePortTrillOutFrames Counter64 } rbridgePortRpfCheckFails OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a multi-destination frame was dropped on this port because the Reverse Path Forwarding (RPF) check failed. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime object of the associated interface." REFERENCE "RFC 6325, Section 4.5.2" ::= { rbridgePortCounterEntry 1 } rbridgePortHopCountExceeds OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a frame was dropped on this port because its hop count was zero. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime object of the associated interface." REFERENCE "RFC 6325, Section 3.6" ::= { rbridgePortCounterEntry 2 } rbridgePortOptionDrops OBJECT-TYPE SYNTAX Counter32 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times a frame was dropped on this port because it contained unsupported options. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime object of the associated interface." REFERENCE "RFC 6325, Section 3.5" ::= { rbridgePortCounterEntry 3 } rbridgePortTrillInFrames OBJECT-TYPE SYNTAX Counter64 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of TRILL-encapsulated frames that have been received by this port from its attached link, including management frames. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime object of the associated interface." REFERENCE "RFC 6325, Section 2.3" ::= { rbridgePortCounterEntry 4 } rbridgePortTrillOutFrames OBJECT-TYPE SYNTAX Counter64 UNITS "frames" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of TRILL-encapsulated frames that have been transmitted by this port to its attached link, including management frames. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime object of the associated interface." REFERENCE "RFC 6325, Section 2.3" ::= { rbridgePortCounterEntry 5 } -- ---------------------------------------------------------- -- -- The RBridge VLAN ESADI Table -- ---------------------------------------------------------- -- rbridgeEsadiTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeEsadiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that contains information about ESADI instances on VLANs, if available." REFERENCE "RFC 6325, Section 4.2.5" ::= { rbridgeEsadi 1 } rbridgeEsadiEntry OBJECT-TYPE SYNTAX RbridgeEsadiEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about an ESADI instance on a VLAN." INDEX { rbridgeVlanIndex } ::= { rbridgeEsadiTable 1 } RbridgeEsadiEntry ::= SEQUENCE { rbridgeEsadiEnable TruthValue, rbridgeEsadiConfidence Unsigned32, rbridgeEsadiDrbPriority Unsigned32, rbridgeEsadiDrb RbridgeAddress, rbridgeEsadiDrbHoldingTime Unsigned32, rbridgeEsadiRowStatus RowStatus } rbridgeEsadiEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "If the RBridge is participating in an ESADI instance for this VLAN, the value of this object is 'true'. To disable participation, set it to 'false'. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.2.5" DEFVAL { true } ::= { rbridgeEsadiEntry 1 } rbridgeEsadiConfidence OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Confidence level of address entries sent by this ESADI instance. The default is 16. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.2.5" DEFVAL { 16 } ::= { rbridgeEsadiEntry 2 } rbridgeEsadiDrbPriority OBJECT-TYPE SYNTAX Unsigned32 (0..127) MAX-ACCESS read-create STATUS current DESCRIPTION "The priority of this RBridge for being selected as the DRB for this ESADI instance. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.2.5" ::= { rbridgeEsadiEntry 3 } rbridgeEsadiDrb OBJECT-TYPE SYNTAX RbridgeAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The DRB on this ESADI instance's virtual link." REFERENCE "RFC 6325, Section 4.2.5" ::= { rbridgeEsadiEntry 4 } rbridgeEsadiDrbHoldingTime OBJECT-TYPE SYNTAX Unsigned32 (0..127) MAX-ACCESS read-create STATUS current DESCRIPTION "The holding time for this ESADI instance. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.2.5" ::= { rbridgeEsadiEntry 5 } rbridgeEsadiRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object indicates the status of the entry." ::= { rbridgeEsadiEntry 6 } -- ---------------------------------------------------------- -- -- The RBridge IP Multicast Snooping Port Table -- ---------------------------------------------------------- -- rbridgeSnoopingPortTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeSnoopingPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "For RBridges implementing IP Multicast Snooping, information about ports on which the presence of IPv4 or IPv6 multicast routers has been detected." REFERENCE "RFC 6325, Section 4.7" ::= { rbridgeSnooping 1 } rbridgeSnoopingPortEntry OBJECT-TYPE SYNTAX RbridgeSnoopingPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about ports on which the presence of IPv4 or IPv6 multicast routers has been detected for a VLAN." INDEX { rbridgeBasePort, rbridgeVlanIndex } ::= { rbridgeSnoopingPortTable 1 } RbridgeSnoopingPortEntry ::= SEQUENCE { rbridgeSnoopingPortAddrType INTEGER } rbridgeSnoopingPortAddrType OBJECT-TYPE SYNTAX INTEGER { ipv4(1), ipv6(2), ipv4v6(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address type of an IP multicast router detected on this port and VLAN. If only IPv4 router(s) are detected, the value returned is 'ipv4'. If only IPv6 routers are detected, the value returned is 'ipv6'. If both IPv4 and IPv6 routers are detected on this port and VLAN, the value returned is 'ipv4v6'." REFERENCE "RFC 6325, Section 4.7" ::= { rbridgeSnoopingPortEntry 1 } -- ---------------------------------------------------------- -- -- The RBridge IP Multicast Snooping Address Table -- ---------------------------------------------------------- -- rbridgeSnoopingAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeSnoopingAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "For RBridges implementing IP Multicast Snooping, information about IP multicast addresses being snooped." REFERENCE "RFC 6325, Section 4.8" ::= { rbridgeSnooping 2 } rbridgeSnoopingAddrEntry OBJECT-TYPE SYNTAX RbridgeSnoopingAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about IP multicast addresses being snooped." INDEX { rbridgeVlanIndex, rbridgeSnoopingAddrType, rbridgeSnoopingAddr } ::= { rbridgeSnoopingAddrTable 1 } RbridgeSnoopingAddrEntry ::= SEQUENCE { rbridgeSnoopingAddrType InetAddressType, rbridgeSnoopingAddr InetAddress, rbridgeSnoopingAddrPorts PortList } rbridgeSnoopingAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast address type for which a listener has been detected by this RBridge. This MIB requires support for only IPv4 and IPv6 address types." REFERENCE "RFC 6325, Section 4.7" ::= { rbridgeSnoopingAddrEntry 1 } rbridgeSnoopingAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast address for which a listener has been detected by this RBridge. The address type of this object is specified in rbridgeSnoopingAddrType. This MIB requires support for only global IPv4 and IPv6 addresses, so the length of the object can be either 4 or 16 bytes. Hence, the index will not exceed the OID size limit." REFERENCE "RFC 6325, Section 4.7" ::= { rbridgeSnoopingAddrEntry 2 } rbridgeSnoopingAddrPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports on which a listener has been detected for this IP multicast address." REFERENCE "RFC 6325, Section 4.7" ::= { rbridgeSnoopingAddrEntry 3 } -- ---------------------------------------------------------- -- -- Distribution Trees -- ---------------------------------------------------------- -- rbridgeDtreePriority OBJECT-TYPE SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The distribution tree root priority for this RBridge. The default value of this object is 32768. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.5" ::= { rbridgeDtree 1 } rbridgeDtreeActiveTrees OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of trees being computed by all RBridges in the campus." REFERENCE "RFC 6325, Section 4.5" ::= { rbridgeDtree 2 } rbridgeDtreeMaxTrees OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of trees this RBridge can compute." REFERENCE "RFC 6325, Section 4.5" ::= { rbridgeDtree 3 } rbridgeDtreeDesiredUseTrees OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of trees this RBridge would like to use for transmission of ingress multi-destination frames." REFERENCE "RFC 6325, Section 4.5" ::= { rbridgeDtree 4 } rbridgeDtreeTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeDtreeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about distribution trees being computed by this RBridge." REFERENCE "RFC 6325, Section 4.5" ::= { rbridgeDtree 5 } rbridgeDtreeEntry OBJECT-TYPE SYNTAX RbridgeDtreeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of information about distribution trees being computed by this RBridge." INDEX { rbridgeDtreeNumber } ::= { rbridgeDtreeTable 1 } RbridgeDtreeEntry ::= SEQUENCE { rbridgeDtreeNumber Unsigned32, rbridgeDtreeNickname RbridgeNickname, rbridgeDtreeIngress TruthValue } rbridgeDtreeNumber OBJECT-TYPE SYNTAX Unsigned32 (0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The tree number of a distribution tree being computed by this RBridge." REFERENCE "RFC 6325, Section 4.5" ::= { rbridgeDtreeEntry 1 } rbridgeDtreeNickname OBJECT-TYPE SYNTAX RbridgeNickname MAX-ACCESS read-only STATUS current DESCRIPTION "The nickname of the distribution tree." REFERENCE "RFC 6325, Section 4.5" ::= { rbridgeDtreeEntry 2 } rbridgeDtreeIngress OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether this RBridge might choose this distribution tree to ingress a multi-destination frame." REFERENCE "RFC 6325, Section 4.5" ::= { rbridgeDtreeEntry 3 } -- ---------------------------------------------------------- -- -- TRILL Neighbor List -- ---------------------------------------------------------- -- rbridgeTrillMinMtuDesired OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The desired minimum acceptable inter-RBridge link MTU for the campus, that is, originatingLSPBufferSize. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.3" ::= { rbridgeTrill 1 } rbridgeTrillSz OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum acceptable inter-RBridge link size for the campus for the proper operation of TRILL IS-IS." REFERENCE "RFC 6325, Section 4.3" ::= { rbridgeTrill 2 } rbridgeTrillMaxMtuProbes OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The number of failed MTU-probes before the RBridge concludes that a particular MTU is not supported by a neighbor. The value of this object MUST be retained across re-initializations of the management system." REFERENCE "RFC 6325, Section 4.3" ::= { rbridgeTrill 3 } rbridgeTrillNbrTable OBJECT-TYPE SYNTAX SEQUENCE OF RbridgeTrillNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about this RBridge's TRILL neighbors." REFERENCE "RFC 6325, Section 4.4.2.1" ::= { rbridgeTrill 4 } rbridgeTrillNbrEntry OBJECT-TYPE SYNTAX RbridgeTrillNbrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "List of information about this RBridge's TRILL neighbors." INDEX { rbridgeTrillNbrMacAddr } ::= { rbridgeTrillNbrTable 1 } RbridgeTrillNbrEntry ::= SEQUENCE { rbridgeTrillNbrMacAddr MacAddress, rbridgeTrillNbrMtu Unsigned32, rbridgeTrillNbrFailedMtuTest TruthValue } rbridgeTrillNbrMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MAC address of a neighbor of this RBridge." REFERENCE "RFC 6325, Section 4.4.2.1" ::= { rbridgeTrillNbrEntry 1 } rbridgeTrillNbrMtu OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "MTU size for this neighbor for IS-IS communication purposes." REFERENCE "RFC 6325, Section 4.3.2" ::= { rbridgeTrillNbrEntry 2 } rbridgeTrillNbrFailedMtuTest OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If true, indicates that the neighbor's tested MTU is less than the minimum acceptable inter-bridge link MTU for the campus (1470)." REFERENCE "RFC 6325, Section 4.3.1" ::= { rbridgeTrillNbrEntry 3 } -- ---------------------------------------------------------- -- -- Notifications for use by RBridges -- ---------------------------------------------------------- -- rbridgeBaseNewDrb NOTIFICATION-TYPE -- OBJECTS { } STATUS current DESCRIPTION "The rbridgeBaseNewDrb notification indicates that the sending agent has become the new Designated RBridge; the notification is sent by an RBridge soon after its election as the new DRB root, e.g., upon expiration of the Topology Change Timer, immediately subsequent to its election." ::= { rbridgeNotifications 1 } rbridgeBaseTopologyChange NOTIFICATION-TYPE -- OBJECTS { } STATUS current DESCRIPTION "The rbridgeBaseTopologyChange notification is sent by an RBridge when any of its configured ports transition to/from the VLAN-x designated forwarder. The notification is not sent if an rbridgeBaseNewDrb notification is sent for the same transition." ::= { rbridgeNotifications 2 } -- Compliance and Group sections rbridgeCompliances OBJECT IDENTIFIER ::= { rbridgeConformance 1 } rbridgeGroup OBJECT IDENTIFIER ::= { rbridgeConformance 2 } -- ---------------------------------------------------------- -- -- Units of Conformance -- ---------------------------------------------------------- -- rbridgeBaseGroup OBJECT-GROUP OBJECTS { rbridgeBaseTrillVersion, rbridgeBaseNumPorts, rbridgeBaseForwardDelay, rbridgeBaseUniMultipathEnable, rbridgeBaseMultiMultipathEnable, rbridgeBaseAcceptEncapNonadj, rbridgeBaseNicknameNumber } STATUS current DESCRIPTION "A collection of objects providing basic control and status information for the RBridge." ::= { rbridgeGroup 1 } rbridgeBaseNicknameGroup OBJECT-GROUP OBJECTS { rbridgeBaseNicknamePriority, rbridgeBaseNicknameDtrPriority, rbridgeBaseNicknameType, rbridgeBaseNicknameRowStatus } STATUS current DESCRIPTION "A collection of objects providing basic control and status information for RBridge nicknames." ::= { rbridgeGroup 2 } rbridgeBasePortGroup OBJECT-GROUP OBJECTS { rbridgeBasePortIfIndex, rbridgeBasePortDisable, rbridgeBasePortTrunkPort, rbridgeBasePortAccessPort, rbridgeBasePortP2pHellos, rbridgeBasePortState, rbridgeBasePortDesiredDesigVlan, rbridgeBasePortDesigVlan, rbridgeBasePortInhibitionTime, rbridgeBasePortDisableLearning, rbridgeBasePortStpRoot, rbridgeBasePortStpRootChanges, rbridgeBasePortStpWiringCloset } STATUS current DESCRIPTION "A collection of objects providing basic control and status information for RBridge ports." ::= { rbridgeGroup 3 } rbridgeFdbGroup OBJECT-GROUP OBJECTS { rbridgeConfidenceNative, rbridgeConfidenceDecap, rbridgeConfidenceStatic, rbridgeUniFdbPort, rbridgeUniFdbNickname, rbridgeUniFdbConfidence, rbridgeUniFdbStatus } STATUS current DESCRIPTION "A collection of objects providing information about the Unicast Address Database." ::= { rbridgeGroup 4 } rbridgeFibGroup OBJECT-GROUP OBJECTS { rbridgeUniFibHopCount, rbridgeMultiFibPorts } STATUS current DESCRIPTION "A collection of objects providing information about the Unicast and Multicast FIBs." ::= { rbridgeGroup 5 } rbridgeVlanGroup OBJECT-GROUP OBJECTS { rbridgeVlanForwarderLosts, rbridgeVlanDisableLearning, rbridgeVlanSnooping, rbridgeVlanPortInhibited, rbridgeVlanPortForwarder, rbridgeVlanPortAnnouncing, rbridgeVlanPortDetectedVlanMapping } STATUS current DESCRIPTION "A collection of objects providing information about VLANs on the RBridge." ::= { rbridgeGroup 6 } rbridgePortCounterGroup OBJECT-GROUP OBJECTS { rbridgePortRpfCheckFails, rbridgePortHopCountExceeds, rbridgePortOptionDrops, rbridgePortTrillInFrames, rbridgePortTrillOutFrames } STATUS current DESCRIPTION "A collection of objects providing per-port counters for the RBridge." ::= { rbridgeGroup 7 } rbridgeEsadiGroup OBJECT-GROUP OBJECTS { rbridgeEsadiEnable, rbridgeEsadiConfidence, rbridgeEsadiDrbPriority, rbridgeEsadiDrb, rbridgeEsadiDrbHoldingTime, rbridgeEsadiRowStatus } STATUS current DESCRIPTION "A collection of objects providing information about ESADI instances on the RBridge." ::= { rbridgeGroup 8 } rbridgeSnoopingGroup OBJECT-GROUP OBJECTS { rbridgeSnoopingPortAddrType, rbridgeSnoopingAddrPorts } STATUS current DESCRIPTION "A collection of objects providing information about IP Multicast Snooping. This MIB requires support for only global IPv4 and IPv6 address types in rbridgeSnoopingPortAddrType and rbridgeSnoopingAddrType, so the length of rbridgeSnoopingAddr can be either 4 or 16 bytes." ::= { rbridgeGroup 9 } rbridgeDtreeGroup OBJECT-GROUP OBJECTS { rbridgeDtreePriority, rbridgeDtreeActiveTrees, rbridgeDtreeMaxTrees, rbridgeDtreeDesiredUseTrees, rbridgeDtreeNickname, rbridgeDtreeIngress } STATUS current DESCRIPTION "A collection of objects providing information about distribution trees." ::= { rbridgeGroup 10 } rbridgeTrillGroup OBJECT-GROUP OBJECTS { rbridgeTrillMinMtuDesired, rbridgeTrillSz, rbridgeTrillMaxMtuProbes, rbridgeTrillNbrMtu, rbridgeTrillNbrFailedMtuTest } STATUS current DESCRIPTION "A collection of objects providing information about TRILL neighbors." ::= { rbridgeGroup 11 } rbridgeNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { rbridgeBaseNewDrb, rbridgeBaseTopologyChange } STATUS current DESCRIPTION "A collection of objects describing notifications (traps)." ::= { rbridgeGroup 12 } -- ---------------------------------------------------------- -- -- Compliance Statement -- ---------------------------------------------------------- -- rbridgeCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for support of RBridge services." MODULE MANDATORY-GROUPS { rbridgeBaseGroup, rbridgeBaseNicknameGroup, rbridgeBasePortGroup, rbridgeFdbGroup, rbridgeFibGroup, rbridgeVlanGroup, rbridgeDtreeGroup, rbridgeTrillGroup, rbridgeNotificationGroup } GROUP rbridgePortCounterGroup DESCRIPTION "Implementation of this group is optional." GROUP rbridgeEsadiGroup DESCRIPTION "Implementation of this group is optional." GROUP rbridgeSnoopingGroup DESCRIPTION "Implementation of this group is optional." ::= { rbridgeCompliances 1 } rbridgeReadOnlyCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "When this MIB is implemented in read-only mode, then the implementation can claim read-only compliance. In that case, RBridge objects can be monitored but cannot be configured with this implementation." MODULE MANDATORY-GROUPS { rbridgeBaseGroup, rbridgeBaseNicknameGroup, rbridgeBasePortGroup, rbridgeFdbGroup, rbridgeFibGroup, rbridgeVlanGroup, rbridgeDtreeGroup, rbridgeTrillGroup, rbridgeNotificationGroup } OBJECT rbridgeBaseForwardDelay MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBaseUniMultipathEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBaseMultiMultipathEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBaseAcceptEncapNonadj MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBaseNicknameNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBaseNicknamePriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBaseNicknameDtrPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBaseNicknameRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and 'active' is the only status that needs to be supported." OBJECT rbridgeBasePortDisable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBasePortTrunkPort MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBasePortAccessPort MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBasePortP2pHellos MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBasePortInhibitionTime MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBasePortDisableLearning MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBasePortDesiredDesigVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeBasePortStpWiringCloset MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeConfidenceNative MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeConfidenceDecap MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeConfidenceStatic MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeVlanDisableLearning MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeVlanPortAnnouncing MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeEsadiEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeEsadiConfidence MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeEsadiDrbPriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeEsadiDrbHoldingTime MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeEsadiRowStatus SYNTAX INTEGER { active(1) } MIN-ACCESS read-only DESCRIPTION "Write access is not required, and 'active' is the only status that needs to be supported." OBJECT rbridgeDtreePriority MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeTrillMinMtuDesired MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT rbridgeTrillMaxMtuProbes MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP rbridgePortCounterGroup DESCRIPTION "Implementation of this group is optional." GROUP rbridgeEsadiGroup DESCRIPTION "Implementation of this group is optional." GROUP rbridgeSnoopingGroup DESCRIPTION "Implementation of this group is optional." ::= { rbridgeCompliances 2 } END