G9981-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2, Unsigned32, Counter32 FROM SNMPv2-SMI -- RFC 2578 TEXTUAL-CONVENTION, TruthValue FROM SNMPv2-TC -- RFC 2579 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC 2580 ifIndex FROM IF-MIB -- RFC 2863 HCPerfCurrentCount, HCPerfIntervalCount, HCPerfValidIntervals, HCPerfInvalidIntervals, HCPerfTimeElapsed FROM HC-PerfHist-TC-MIB -- RFC 3705 ; ------------------------------------------------------------------------ g9981MIB MODULE-IDENTITY LAST-UPDATED "201302200000Z" -- 20 February 2013 ORGANIZATION "IETF ADSL MIB Working Group" CONTACT-INFO "WG charter: http://datatracker.ietf.org/wg/adslmib/charter/ Mailing Lists: General Discussion: adslmib@ietf.org To Subscribe: adslmib-request@ietf.org In Body: subscribe your_email_address Chair: Menachem Dodge Postal: ECI Telecom, Ltd. 30 Hasivim St., Petach-Tikva 4951169 Israel Phone: +972-3-926-8421 EMail: menachemdodge1@gmail.com Editor: Edward Beili Postal: Actelis Networks, Inc. 25 Bazel St., P.O.B. 10173 Petach-Tikva 49103 Israel Phone: +972-3-924-3491 EMail: edward.beili@actelis.com" DESCRIPTION "The objects in this MIB module are used to manage the multi-pair bonded xDSL interfaces using ATM inverse multiplexing, as defined in ITU-T Recommendation G.998.1 (G.Bond/ATM). This MIB module MUST be used in conjunction with the GBOND-MIB module, common to all G.Bond technologies. The following references are used throughout this MIB module: [G.998.1] refers to: ITU-T Recommendation G.998.1: 'ATM-based multi-pair bonding', January 2005. [TR-159] refers to: Broadband Forum Technical Report: 'Management Framework for xDSL Bonding', December 2008. Naming Conventions: ATM - Asynchronous Transfer Mode BCE - Bonding Channel Entity BTU - Bonding Terminating Unit CO - Central Office CPE - Customer Premises Equipment GBS - Generic Bonding Sub-layer GBS-C - Generic Bonding Sub-layer, CO side GBS-R - Generic Bonding Sub-layer, RT (or CPE) side PM - Performance Monitoring RT - Remote Terminal SNR - Signal to Noise Ratio SES - Severely Errored Seconds UAS - Unavailable Seconds Copyright (c) 2013 IETF Trust and the persons identified as authors of the code. All rights reserved. Redistribution and use in source and binary forms, with or without modification, is permitted pursuant to, and subject to the license terms contained in, the Simplified BSD License set forth in Section 4.c of the IETF Trust's Legal Provisions Relating to IETF Documents (http://trustee.ietf.org/license-info)." REVISION "201302200000Z" -- 20 February 2013 DESCRIPTION "Initial version, published as RFC 6768." ::= { mib-2 208 } -- Sections of the module -- Structured as recommended by RFC 4181, Appendix D g9981Objects OBJECT IDENTIFIER ::= { g9981MIB 1 } g9981Conformance OBJECT IDENTIFIER ::= { g9981MIB 2 } -- Groups in the module g9981Port OBJECT IDENTIFIER ::= { g9981Objects 1 } -- Textual Conventions MilliSeconds ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "Represents time unit value in milliseconds." SYNTAX Unsigned32 -- Port Notifications group g9981PortNotifications OBJECT IDENTIFIER ::= { g9981Port 0 } g9981UpDiffDelayToleranceExceeded NOTIFICATION-TYPE OBJECTS { -- ifIndex is not needed here, since we are under specific GBS g9981PortConfUpDiffDelayTolerance, g9981PortStatMaxUpDiffDelay } STATUS current DESCRIPTION "This notification indicates that the maximum upstream differential delay has exceeded the max upstream differential delay threshold, specified by g9981PortConfUpDiffDelayTolerance. This notification MAY be sent for the GBS-C ports while the port is 'up', on the crossing event in both directions: from normal (diff. delay is above the threshold) to low (diff. delay equals the threshold or is below it) and from low to normal. This notification is not applicable to the GBS-R ports. Generation of this notification is controlled by the g9981PortConfDiffDelayToleranceExceededEnable attribute. This object maps to the TR-159 notification nIMAUpDiffDelayToleranceExceeded." REFERENCE "[TR-159], Section 5.5.2.8" ::= { g9981PortNotifications 1 } g9981DnDiffDelayToleranceExceeded NOTIFICATION-TYPE OBJECTS { -- ifIndex is not needed here, since we are under specific GBS g9981PortConfDnDiffDelayTolerance, g9981PortStatMaxDnDiffDelay } STATUS current DESCRIPTION "This notification indicates that the maximum downstream differential delay has exceeded the max downstream differential delay threshold, specified by g9981PortConfDnDiffDelayTolerance. This notification MAY be sent for the GBS-C ports while the port is 'up', on the crossing event in both directions: from normal (diff. delay is above the threshold) to low (diff. delay equals the threshold or is below it) and from low to normal. This notification is not applicable to the GBS-R ports. Generation of this notification is controlled by the g9981PortConfDiffDelayToleranceExceededEnable attribute. This object maps to the TR-159 notification nIMADownDiffDelayToleranceExceeded." REFERENCE "[TR-159], Section 5.5.2.9" ::= { g9981PortNotifications 2 } -- G.Bond/ATM Port group g9981PortConfTable OBJECT-TYPE SYNTAX SEQUENCE OF G9981PortConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table for configuration of G.Bond/ATM ports. Entries in this table MUST be maintained in a persistent manner." ::= { g9981Port 1 } g9981PortConfEntry OBJECT-TYPE SYNTAX G9981PortConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/ATM Port Configuration table. Each entry represents a G.Bond/ATM port indexed by the ifIndex. Additional configuration parameters are available via the gBondPortConfEntry of the GBOND-MIB. Note that a G.Bond/ATM port runs on top of a single or multiple BCE port(s), which are also indexed by the ifIndex." INDEX { ifIndex } ::= { g9981PortConfTable 1 } G9981PortConfEntry ::= SEQUENCE { g9981PortConfUpDiffDelayTolerance MilliSeconds, g9981PortConfDnDiffDelayTolerance MilliSeconds, g9981PortConfDiffDelayToleranceExceededEnable TruthValue } g9981PortConfUpDiffDelayTolerance OBJECT-TYPE SYNTAX MilliSeconds (0..2047) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "A maximum tolerated upstream differential delay (among the member BCEs) of a G.Bond/ATM port, expressed in ms. This object is read-write for the GBS-C ports. It is irrelevant for the GBS-R ports -- an attempt to read or change this object MUST be rejected (in the case of SNMP, with the error inconsistentValue). This object maps to the TR-159 attribute aIMAUpDiffDelayTolerance." REFERENCE "[TR-159], Section 5.5.2.5; [G.998.1], Section 11.4.1 (6)" ::= { g9981PortConfEntry 1 } g9981PortConfDnDiffDelayTolerance OBJECT-TYPE SYNTAX MilliSeconds (0..2047) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "A maximum tolerated downstream differential delay (among the member BCEs) of a G.Bond/ATM port, expressed in ms. This object is read-write for the GBS-C ports. It is irrelevant for the GBS-R ports -- an attempt to read or change this object MUST be rejected (in the case of SNMP, with the error inconsistentValue). This object maps to the TR-159 attribute aIMADownDiffDelayTolerance." REFERENCE "[TR-159], Section 5.5.2.6; [G.998.1], Section 11.4.1 (6)" ::= { g9981PortConfEntry 2 } g9981PortConfDiffDelayToleranceExceededEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Indicates whether g9981UpDiffDelayToleranceExceeded and g9981DnDiffDelayToleranceExceeded notifications should be generated for G.Bond/ATM port. A value of true(1) indicates that the notifications are enabled. A value of false(2) indicates that the notifications are disabled. This object is read-write for the GBS-C. It is irrelevant for the GBS-R ports -- an attempt to read or change this object MUST be rejected (in the case of SNMP, with the error inconsistentValue). This object maps to the TR-159 attribute aIMADiffDelayToleranceExceededEnable." REFERENCE "[TR-159], Section 5.5.5.7" ::= { g9981PortConfEntry 3 } g9981PortStatTable OBJECT-TYPE SYNTAX SEQUENCE OF G9981PortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides overall status information of G.Bond/ATM ports, complementing the generic status information from the ifTable of the IF-MIB and the gBondFltStatus of the GBOND-MIB. Additional status information about connected BCEs is available from the relevant line MIBs. This table contains live data from the equipment. As such, it is NOT persistent." ::= { g9981Port 2 } g9981PortStatEntry OBJECT-TYPE SYNTAX G9981PortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/ATM Port Status table. Each entry represents a G.Bond/ATM port indexed by the ifIndex. Note that a GBS port runs on top of a single or multiple BCE port(s), which are also indexed by the ifIndex." INDEX { ifIndex } ::= { g9981PortStatTable 1 } G9981PortStatEntry ::= SEQUENCE { g9981PortStatRxLostCells Counter32, g9981PortStatTxLostCells Counter32, g9981PortStatMaxUpDiffDelay Unsigned32, g9981PortStatMaxDnDiffDelay Unsigned32 } g9981PortStatRxLostCells OBJECT-TYPE SYNTAX Counter32 UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of lost ATM cells detected by the G.Bond/ATM port in the receive direction (e.g., upstream direction for a GBS-C port). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime as defined in the IF-MIB. This object maps to the TR-159 attribute aIMARxLostCells." REFERENCE "[TR-159], Section 5.5.2.1; [G.998.1], Section 11.4.2 (4)" ::= { g9981PortStatEntry 1 } g9981PortStatTxLostCells OBJECT-TYPE SYNTAX Counter32 UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "The number of lost ATM cells detected by the peer G.Bond/ATM port in the receive direction, i.e., downstream direction for a GBS-C port. This object is irrelevant for the GBS-R ports -- an attempt to read it MUST be rejected (in the case of SNMP, with the error inconsistentValue). Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime as defined in the IF-MIB. This object maps to the TR-159 attribute aIMAPeerRxLostCells." REFERENCE "[TR-159], Section 5.5.2.2; [G.998.1], Section 11.4.2 (4)" ::= { g9981PortStatEntry 2 } g9981PortStatMaxUpDiffDelay OBJECT-TYPE SYNTAX Unsigned32 UNITS "0.1 ms" MAX-ACCESS read-only STATUS current DESCRIPTION "Current maximum upstream differential delay between all operational BCEs in the G.Bond/ATM bonding group, measured in units of 0.1 ms. This object is read-only for the GBS-C ports. It is irrelevant for the GBS-R ports -- an attempt to read this object MUST be rejected (in the case of SNMP, with the error inconsistentValue). This object maps to the TR-159 attribute aIMAMaxUpDiffDelay." REFERENCE "[TR-159], Section 5.5.2.3" ::= { g9981PortStatEntry 3 } g9981PortStatMaxDnDiffDelay OBJECT-TYPE SYNTAX Unsigned32 UNITS "0.1 ms" MAX-ACCESS read-only STATUS current DESCRIPTION "Current maximum downstream differential delay between all operational BCEs in the G.Bond/ATM bonding group, measured in units of 0.1 ms. This object is read-only for the GBS-C ports. It is irrelevant for the GBS-R ports -- an attempt to read this object MUST be rejected (in the case of SNMP, with the error inconsistentValue). This object maps to the TR-159 attribute aIMAMaxDownDiffDelay." REFERENCE "[TR-159], Section 5.5.2.4" ::= { g9981PortStatEntry 4 } ------------------------------- -- Performance Monitoring group ------------------------------- g9981PM OBJECT IDENTIFIER ::= { g9981Port 3 } g9981PortPmCurTable OBJECT-TYPE SYNTAX SEQUENCE OF G9981PortPmCurEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains current Performance Monitoring information for a G.Bond/ATM port. This table contains live data from the equipment and as such is NOT persistent." ::= { g9981PM 1 } g9981PortPmCurEntry OBJECT-TYPE SYNTAX G9981PortPmCurEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/ATM Port PM table. Each entry represents a G.Bond/ATM port indexed by the ifIndex." INDEX { ifIndex } ::= { g9981PortPmCurTable 1 } G9981PortPmCurEntry ::= SEQUENCE { g9981PortPmCur15MinValidIntervals HCPerfValidIntervals, g9981PortPmCur15MinInvalidIntervals HCPerfInvalidIntervals, g9981PortPmCur15MinTimeElapsed HCPerfTimeElapsed, g9981PortPmCur15MinRxLostCells HCPerfCurrentCount, g9981PortPmCur15MinTxLostCells HCPerfCurrentCount, g9981PortPmCur15MinUpDiffDelay HCPerfCurrentCount, g9981PortPmCur15MinDnDiffDelay HCPerfCurrentCount, g9981PortPmCur1DayValidIntervals Unsigned32, g9981PortPmCur1DayInvalidIntervals Unsigned32, g9981PortPmCur1DayTimeElapsed HCPerfTimeElapsed, g9981PortPmCur1DayRxLostCells HCPerfCurrentCount, g9981PortPmCur1DayTxLostCells HCPerfCurrentCount, g9981PortPmCur1DayUpDiffDelay HCPerfCurrentCount, g9981PortPmCur1DayDnDiffDelay HCPerfCurrentCount } g9981PortPmCur15MinValidIntervals OBJECT-TYPE SYNTAX HCPerfValidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 15-minute intervals for which the performance data was collected. The value of this object will be 96 or the maximum number of 15-minute history intervals collected by the implementation, unless the measurement was (re)started recently, in which case the value will be the number of complete 15-minute intervals for which there are at least some data. In certain cases, it is possible that some intervals are unavailable. In this case, this object reports the maximum interval number for which data is available. This object partially maps to the TR-159 attribute aGroupPerf15MinValidIntervals." REFERENCE "[TR-159], Section 5.5.1.32" ::= { g9981PortPmCurEntry 1 } g9981PortPmCur15MinInvalidIntervals OBJECT-TYPE SYNTAX HCPerfInvalidIntervals MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 15-minute intervals for which the performance data was not always available. The value will typically be zero, except in cases where the data for some intervals are not available. This object partially maps to the TR-159 attribute aGroupPerf15MinInvalidIntervals." REFERENCE "[TR-159], Section 5.5.1.33" ::= { g9981PortPmCurEntry 2 } g9981PortPmCur15MinTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds that have elapsed since the beginning of the current 15-minute performance interval. This object partially maps to the TR-159 attribute aGroupPerfCurr15MinTimeElapsed." REFERENCE "[TR-159], Section 5.5.1.34" ::= { g9981PortPmCurEntry 3 } g9981PortPmCur15MinRxLostCells OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of lost ATM cells detected by a G.Bond/ATM port (e.g., the GBS-C) in the receive direction, during the current 15-minute performance history interval. Note that the total number of lost ATM cells is indicated by the g9981PortStatRxLostCells object. This object is inhibited during Severely Errored Seconds (SES) or Unavailable Seconds (UAS)." REFERENCE "[TR-159], Section 5.5.2.1" ::= { g9981PortPmCurEntry 4} g9981PortPmCur15MinTxLostCells OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of lost ATM cells detected by the peer G.Bond/ATM port (e.g., by the GBS-R for the GBS-C) during the current 15-minute performance history interval. Note that the total number of lost ATM cells is indicated by the g9981PortStatTxLostCells object. This object is inhibited during Unavailable Seconds (UAS)." REFERENCE "[TR-159], Section 5.5.2.2" ::= { g9981PortPmCurEntry 5} g9981PortPmCur15MinUpDiffDelay OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "0.1 ms" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value specifying the maximum upstream differential delay between all operational BCEs in the GBS-C, measured in units of 0.1 ms, during the current 15-minute performance interval. Note that the current max upstream differential delay is indicated by the g9981PortStatMaxUpDiffDelay object. This object is inhibited during Unavailable Seconds (UAS)." REFERENCE "[TR-159], Section 5.5.2.3" ::= { g9981PortPmCurEntry 6} g9981PortPmCur15MinDnDiffDelay OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "0.1 ms" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value specifying the maximum downstream differential delay between all operational BCEs in the GBS-C (as perceived by the GBS-R), measured in units of 0.1 ms, during the current 15-minute performance history interval. Note that the current max downstream differential delay is indicated by the g9981PortStatMaxDnDiffDelay object. This object is inhibited during Unavailable Seconds (UAS)." REFERENCE "[TR-159], Section 5.5.2.4" ::= { g9981PortPmCurEntry 7} g9981PortPmCur1DayValidIntervals OBJECT-TYPE SYNTAX Unsigned32 (0..7) UNITS "days" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 1-day intervals for which data was collected. The value of this object will be 7 or the maximum number of 1-day history intervals collected by the implementation, unless the measurement was (re)started recently, in which case the value will be the number of complete 1-day intervals for which there are at least some data. In certain cases, it is possible that some intervals are unavailable. In this case, this object reports the maximum interval number for which data is available." REFERENCE "[TR-159], Section 5.5.1.45" ::= { g9981PortPmCurEntry 8 } g9981PortPmCur1DayInvalidIntervals OBJECT-TYPE SYNTAX Unsigned32 (0..7) UNITS "days" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only number of 1-day intervals for which data was not always available. The value will typically be zero, except in cases where the data for some intervals are not available." REFERENCE "[TR-159], Section 5.5.1.46" ::= { g9981PortPmCurEntry 9 } g9981PortPmCur1DayTimeElapsed OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds that have elapsed since the beginning of the current 1-day performance interval." REFERENCE "[TR-159], Section 5.5.1.47" ::= { g9981PortPmCurEntry 10 } g9981PortPmCur1DayRxLostCells OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of lost ATM cells detected by the G.Bond/ATM port (e.g., the GBS-C) during the current 1-day performance interval. This object is inhibited during Severely Errored Seconds (SES) and Unavailable Seconds (UAS)." ::= { g9981PortPmCurEntry 11 } g9981PortPmCur1DayTxLostCells OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of lost ATM cells detected by the peer G.Bond/ATM port (e.g., by the GBS-R for the GBS-C) during the current 1-day performance history interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9981PortPmCurEntry 12 } g9981PortPmCur1DayUpDiffDelay OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "0.1 ms" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value specifying the maximum upstream differential delay between all operational BCEs in the GBS-C, measured in units of 0.1 ms, during the current 1-day performance interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9981PortPmCurEntry 13 } g9981PortPmCur1DayDnDiffDelay OBJECT-TYPE SYNTAX HCPerfCurrentCount UNITS "0.1 ms" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value specifying the maximum downstream differential delay between all operational BCEs in the GBS-C, measured in units of 0.1 ms, during the current 1-day performance interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9981PortPmCurEntry 14 } -- Port PM history: 15-min buckets g9981PortPm15MinTable OBJECT-TYPE SYNTAX SEQUENCE OF G9981PortPm15MinEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains historical 15-minute buckets of Performance Monitoring information for a G.Bond/ATM port (a row for each 15-minute interval, up to 96 intervals). Entries in this table MUST be maintained in a persistent manner." ::= { g9981PM 2 } g9981PortPm15MinEntry OBJECT-TYPE SYNTAX G9981PortPm15MinEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/ATM Port historical 15-minute PM table. Each entry represents Performance Monitoring data for a G.Bond/ATM port, indexed by the ifIndex, collected during a particular 15-minute interval, indexed by the g9981PortPm15MinIntervalIndex." INDEX { ifIndex, g9981PortPm15MinIntervalIndex } ::= { g9981PortPm15MinTable 1 } G9981PortPm15MinEntry ::= SEQUENCE { g9981PortPm15MinIntervalIndex Unsigned32, g9981PortPm15MinIntervalMoniTime HCPerfTimeElapsed, g9981PortPm15MinIntervalRxLostCells HCPerfIntervalCount, g9981PortPm15MinIntervalTxLostCells HCPerfIntervalCount, g9981PortPm15MinIntervalUpDiffDelay HCPerfIntervalCount, g9981PortPm15MinIntervalDnDiffDelay HCPerfIntervalCount, g9981PortPm15MinIntervalValid TruthValue } g9981PortPm15MinIntervalIndex OBJECT-TYPE SYNTAX Unsigned32 (1..96) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance data interval number. 1 is the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are OPTIONAL. This object partially maps to the TR-159 attribute aGroupPerf15MinIntervalNumber." REFERENCE "[TR-159], Section 5.5.1.57" ::= { g9981PortPm15MinEntry 1 } g9981PortPm15MinIntervalMoniTime OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of seconds over which the performance data was actually monitored. This value will be the same as the interval duration (900 seconds), except in a situation where performance data could not be collected for any reason." ::= { g9981PortPm15MinEntry 2 } g9981PortPm15MinIntervalRxLostCells OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of lost ATM cells detected by a G.Bond/ATM port (e.g., the GBS-C) in the receive direction, during the 15-minute performance history interval. Note that the total number of lost ATM cells is indicated by the g9981PortStatRxLostCells object. This object is inhibited during Severely Errored Seconds (SES) or Unavailable Seconds (UAS)." REFERENCE "[TR-159], Section 5.5.2.1" ::= { g9981PortPm15MinEntry 3 } g9981PortPm15MinIntervalTxLostCells OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only count of lost ATM cells detected by the peer G.Bond/ATM port (e.g., by the GBS-R for the GBS-C) during the 15-minute performance history interval. Note that the total number of lost ATM cells is indicated by the g9981PortStatTxLostCells object. This object is inhibited during Unavailable Seconds (UAS)." REFERENCE "[TR-159], Section 5.5.2.2" ::= { g9981PortPm15MinEntry 4 } g9981PortPm15MinIntervalUpDiffDelay OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "0.1 ms" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value specifying the maximum upstream differential delay between all operational BCEs in the GBS, measured in units of 0.1 ms, during the 15-minute performance history interval. Note that the current max upstream differential delay is indicated by the g9981PortStatMaxUpDiffDelay object. This object is inhibited during Unavailable Seconds (UAS)." REFERENCE "[TR-159], Section 5.5.2.3" ::= { g9981PortPm15MinEntry 5 } g9981PortPm15MinIntervalDnDiffDelay OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "0.1 ms" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value specifying the maximum downstream differential delay between all operational BCEs in the GBS, as perceived by its peer port, measured in units of 0.1 ms, during the 15-minute performance history interval. Note that the current max downstream differential delay is indicated by the g9981PortStatMaxDnDiffDelay object. This object is inhibited during Unavailable Seconds (UAS)." REFERENCE "[TR-159], Section 5.5.2.4" ::= { g9981PortPm15MinEntry 6 } g9981PortPm15MinIntervalValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only object indicating whether or not this history bucket contains valid data. A valid bucket is reported as true(1) and an invalid bucket as false(2). If this history bucket is invalid, the BTU MUST NOT produce notifications based upon the value of the counters in this bucket. Note that an implementation may decide not to store invalid history buckets in its database. In such a case, this object is not required, as only valid history buckets are available while invalid history buckets are simply not in the database. This object partially maps to the TR-159 attribute aGroupPerf15MinIntervalValid." REFERENCE "[TR-159], Section 5.5.1.58" ::= { g9981PortPm15MinEntry 7 } -- Port PM history: 1-day buckets g9981PortPm1DayTable OBJECT-TYPE SYNTAX SEQUENCE OF G9981PortPm1DayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains historical 1-day buckets of Performance Monitoring information for a G.Bond/ATM port (a row for each 1-day interval, up to 7 intervals). Entries in this table MUST be maintained in a persistent manner." ::= { g9981PM 3 } g9981PortPm1DayEntry OBJECT-TYPE SYNTAX G9981PortPm1DayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the G.Bond/ATM Port historical 1-day PM table. Each entry represents Performance Monitoring data for such a port, indexed by the ifIndex, collected during a particular 1-day interval, indexed by the g9981PortPm1DayIntervalIndex." INDEX { ifIndex, g9981PortPm1DayIntervalIndex } ::= { g9981PortPm1DayTable 1 } G9981PortPm1DayEntry ::= SEQUENCE { g9981PortPm1DayIntervalIndex Unsigned32, g9981PortPm1DayIntervalMoniTime HCPerfTimeElapsed, g9981PortPm1DayIntervalRxLostCells HCPerfIntervalCount, g9981PortPm1DayIntervalTxLostCells HCPerfIntervalCount, g9981PortPm1DayIntervalUpDiffDelay HCPerfIntervalCount, g9981PortPm1DayIntervalDnDiffDelay HCPerfIntervalCount, g9981PortPm1DayIntervalValid TruthValue } g9981PortPm1DayIntervalIndex OBJECT-TYPE SYNTAX Unsigned32 (1..7) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Performance data interval number. 1 is the most recent previous interval; interval 7 is 24 hours ago. Intervals 2..7 are OPTIONAL. This object partially maps to the TR-159 attribute aGroupPerf1DayIntervalNumber." REFERENCE "[TR-159], Section 5.5.1.62" ::= { g9981PortPm1DayEntry 1 } g9981PortPm1DayIntervalMoniTime OBJECT-TYPE SYNTAX HCPerfTimeElapsed UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of seconds over which the performance data was actually monitored. This value will be the same as the interval duration (86400 seconds), except in a situation where performance data could not be collected for any reason. This object partially maps to the TR-159 attribute aGroupPerf1DayIntervalMoniSecs." REFERENCE "[TR-159], Section 5.5.1.64" ::= { g9981PortPm1DayEntry 2 } g9981PortPm1DayIntervalRxLostCells OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of lost ATM cells detected by the G.Bond/ATM port (e.g., the GBS-C) during the 1-day performance history interval. This object is inhibited during Severely Errored Seconds (SES) and Unavailable Seconds (UAS)." ::= { g9981PortPm1DayEntry 3 } g9981PortPm1DayIntervalTxLostCells OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "cells" MAX-ACCESS read-only STATUS current DESCRIPTION "A count of lost ATM cells detected by the peer G.Bond/ATM port (e.g., by the GBS-R for the GBS-C) during the 1-day performance history interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9981PortPm1DayEntry 4 } g9981PortPm1DayIntervalUpDiffDelay OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "0.1 ms" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value specifying the maximum upstream differential delay between all operational BCEs in the GBS-C, measured in units of 0.1 ms, during the 1-day performance history interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9981PortPm1DayEntry 5 } g9981PortPm1DayIntervalDnDiffDelay OBJECT-TYPE SYNTAX HCPerfIntervalCount UNITS "0.1 ms" MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only value specifying the maximum downstream differential delay between all operational BCEs in the GBS-C, measured in units of 0.1 ms, during the 1-day performance history interval. This object is inhibited during Unavailable Seconds (UAS)." ::= { g9981PortPm1DayEntry 6 } g9981PortPm1DayIntervalValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A read-only object indicating whether or not this history bucket contains valid data. A valid bucket is reported as true(1) and an invalid bucket as false(2). If this history bucket is invalid, the BTU MUST NOT produce notifications based upon the value of the counters in this bucket. Note that an implementation may decide not to store invalid history buckets in its database. In such a case, this object is not required, as only valid history buckets are available while invalid history buckets are simply not in the database. This object partially maps to the TR-159 attribute aGroupPerf1DayIntervalValid." REFERENCE "[TR-159], Section 5.5.1.63" ::= { g9981PortPm1DayEntry 7 } -- -- Conformance Statements -- g9981Groups OBJECT IDENTIFIER ::= { g9981Conformance 1 } g9981Compliances OBJECT IDENTIFIER ::= { g9981Conformance 2 } -- Object Groups g9981BasicGroup OBJECT-GROUP OBJECTS { g9981PortStatRxLostCells, g9981PortStatTxLostCells, g9981PortStatMaxUpDiffDelay, g9981PortStatMaxDnDiffDelay } STATUS current DESCRIPTION "A collection of objects representing management information for a G.Bond/ATM port." ::= { g9981Groups 1 } g9981AlarmConfGroup OBJECT-GROUP OBJECTS { g9981PortConfUpDiffDelayTolerance, g9981PortConfDnDiffDelayTolerance, g9981PortConfDiffDelayToleranceExceededEnable } STATUS current DESCRIPTION "A collection of objects required for configuration of alarm thresholds and notifications in G.Bond/ATM ports." ::= { g9981Groups 2 } g9981NotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { g9981UpDiffDelayToleranceExceeded, g9981DnDiffDelayToleranceExceeded } STATUS current DESCRIPTION "This group supports notifications of significant conditions associated with G.Bond/ATM ports." ::= { g9981Groups 3 } g9981PerfCurrGroup OBJECT-GROUP OBJECTS { g9981PortPmCur15MinValidIntervals, g9981PortPmCur15MinInvalidIntervals, g9981PortPmCur15MinTimeElapsed, g9981PortPmCur15MinRxLostCells, g9981PortPmCur15MinTxLostCells, g9981PortPmCur15MinUpDiffDelay, g9981PortPmCur15MinDnDiffDelay, g9981PortPmCur1DayValidIntervals, g9981PortPmCur1DayInvalidIntervals, g9981PortPmCur1DayTimeElapsed, g9981PortPmCur1DayRxLostCells, g9981PortPmCur1DayTxLostCells, g9981PortPmCur1DayUpDiffDelay, g9981PortPmCur1DayDnDiffDelay } STATUS current DESCRIPTION "A collection of objects supporting OPTIONAL current Performance Monitoring information for G.Bond/ATM ports." ::= { g9981Groups 4 } g9981Perf15MinGroup OBJECT-GROUP OBJECTS { g9981PortPm15MinIntervalMoniTime, g9981PortPm15MinIntervalRxLostCells, g9981PortPm15MinIntervalTxLostCells, g9981PortPm15MinIntervalUpDiffDelay, g9981PortPm15MinIntervalDnDiffDelay, g9981PortPm15MinIntervalValid } STATUS current DESCRIPTION "A collection of objects supporting OPTIONAL historical Performance Monitoring information for G.Bond/ATM ports, during previous 15-minute intervals." ::= { g9981Groups 5 } g9981Perf1DayGroup OBJECT-GROUP OBJECTS { g9981PortPm1DayIntervalMoniTime, g9981PortPm1DayIntervalRxLostCells, g9981PortPm1DayIntervalTxLostCells, g9981PortPm1DayIntervalUpDiffDelay, g9981PortPm1DayIntervalDnDiffDelay, g9981PortPm1DayIntervalValid } STATUS current DESCRIPTION "A collection of objects supporting OPTIONAL historical Performance Monitoring information for G.Bond/ATM ports, during previous 1-day intervals." ::= { g9981Groups 6 } -- Compliance Statements g9981Compliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for G.Bond/ATM interfaces. Compliance with the following external compliance statements is REQUIRED: MIB Module Compliance Statement ---------- -------------------- IF-MIB ifCompliance3 GBOND-MIB gBondCompliance" MODULE -- this module MANDATORY-GROUPS { g9981BasicGroup, g9981AlarmConfGroup, g9981NotificationGroup } GROUP g9981PerfCurrGroup DESCRIPTION "Support for this group is only required for implementations supporting Performance Monitoring." GROUP g9981Perf15MinGroup DESCRIPTION "Support for this group is only required for implementations supporting historical Performance Monitoring." GROUP g9981Perf1DayGroup DESCRIPTION "Support for this group is only required for implementations supporting 1-day historical Performance Monitoring." ::= { g9981Compliances 1 } END