EFM-CU-MIB DEFINITIONS ::= BEGIN
 
  IMPORTS
    MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32,
    Unsigned32, Counter32, mib-2
      FROM SNMPv2-SMI         -- [RFC2578]
    TEXTUAL-CONVENTION, TruthValue, RowStatus, PhysAddress
      FROM SNMPv2-TC          -- [RFC2579]
    MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP
      FROM SNMPv2-CONF        -- [RFC2580]
    SnmpAdminString
      FROM SNMP-FRAMEWORK-MIB -- [RFC3411]
    ifIndex, ifSpeed
      FROM IF-MIB             -- [RFC2863]
    ;
 
  efmCuMIB MODULE-IDENTITY
    LAST-UPDATED "200711140000Z"  -- November 14, 2007
    ORGANIZATION "IETF Ethernet Interfaces and Hub MIB Working Group"
    CONTACT-INFO
      "WG charter:
        http://www.ietf.org/html.charters/OLD/hubmib-charter.html
 
 
 
      Mailing Lists:
        General Discussion: hubmib@ietf.org
        To Subscribe: hubmib-request@ietf.org
        In Body: subscribe your_email_address
 
      Chair:  Bert Wijnen
      Postal: Alcatel-Lucent
              Schagen 33
              3461 GL Linschoten
              Netherlands
       Phone: +31-348-407-775
       EMail: bwijnen@alcatel-lucent.com
 
      Editor: Edward Beili
      Postal: Actelis Networks Inc.
              25 Bazel St., P.O.B. 10173
              Petach-Tikva 10173
              Israel
       Phone: +972-3-924-3491
       Email: edward.beili@actelis.com"
 
    DESCRIPTION
      "The objects in this MIB module are used to manage
      the Ethernet in the First Mile (EFM) Copper (EFMCu) Interfaces
      2BASE-TL and 10PASS-TS, defined in IEEE Std. 802.3ah-2004,
      which is now a part of IEEE Std. 802.3-2005.
 
      The following references are used throughout this MIB module:
 
      [802.3ah] refers to:
        IEEE Std 802.3ah-2004: 'IEEE Standard for Information
        technology - Telecommunications and information exchange
        between systems - Local and metropolitan area networks -
        Specific requirements -
        Part 3: Carrier Sense Multiple Access with Collision
        Detection (CSMA/CD) Access Method and Physical Layer
        Specifications -
        Amendment: Media Access Control Parameters, Physical
        Layers and Management Parameters for Subscriber Access
        Networks', 07 September 2004.
 
      Of particular interest are Clause 61, 'Physical Coding
      Sublayer (PCS) and common specifications, type 10PASS-TS and
      type 2BASE-TL', Clause 30, 'Management', Clause 45,
      'Management Data Input/Output (MDIO) Interface', Annex 62A,
      'PMD profiles for 10PASS-TS' and Annex 63A, 'PMD profiles for
      2BASE-TL'.
 
 
 
 
      [G.991.2] refers to:
        ITU-T Recommendation G.991.2: 'Single-pair High-speed Digital
        Subscriber Line (SHDSL) transceivers', December 2003.
 
      [ANFP] refers to:
        NICC Document ND1602:2005/08: 'Specification of the Access
        Network Frequency Plan (ANFP) applicable to transmission
        systems used on the BT Access Network,' August 2005.
 
      The following normative documents are quoted by the DESCRIPTION
      clauses in this MIB module:
 
      [G.993.1] refers to:
        ITU-T Recommendation G.993.1: 'Very High speed Digital
        Subscriber Line transceivers', June 2004.
 
      [T1.424] refers to:
        ANSI T1.424-2004: 'Interface Between Networks and Customer
        Installation Very-high-bit-rate Digital Subscriber Lines
        (VDSL) Metallic Interface (DMT Based)', June 2004.
 
      [TS 101 270-1] refers to:
        ETSI TS 101 270-1: 'Transmission and Multiplexing (TM);
        Access transmission systems on metallic access cables;
        Very high speed Digital Subscriber Line (VDSL); Part 1:
        Functional requirements', October 2005.
 
      Naming Conventions:
        Atn   - Attenuation
        CO    - Central Office
        CPE   - Customer Premises Equipment
        EFM   - Ethernet in the First Mile
        EFMCu - EFM Copper
        MDIO  - Management Data Input/Output
        Mgn   - Margin
        PAF   - PME Aggregation Function
        PBO   - Power Back-Off
        PCS   - Physical Coding Sublayer
        PMD   - Physical Medium Dependent
        PME   - Physical Medium Entity
        PSD   - Power Spectral Density
        SNR   - Signal to Noise Ratio
        TCPAM - Trellis Coded Pulse Amplitude Modulation
 
      Copyright (C) The IETF Trust (2007).  This version
      of this MIB module is part of RFC 5066;  see the RFC
      itself for full legal notices."
 
 
 
 
    REVISION    "200711140000Z"  -- November 14, 2007
    DESCRIPTION "Initial version, published as RFC 5066."
 
    ::= { mib-2 167 }
 
   -- Sections of the module
 
   efmCuObjects     OBJECT IDENTIFIER ::= { efmCuMIB 1 }
 
   efmCuConformance OBJECT IDENTIFIER ::= { efmCuMIB 2 }
 
   -- Groups in the module
 
   efmCuPort        OBJECT IDENTIFIER ::= { efmCuObjects 1 }
 
   efmCuPme         OBJECT IDENTIFIER ::= { efmCuObjects 2 }
 
   -- Textual Conventions
 
   EfmProfileIndex ::= TEXTUAL-CONVENTION
     DISPLAY-HINT "d"
     STATUS       current
     DESCRIPTION
       "A unique value, greater than zero, for each PME configuration
       profile in the managed EFMCu port.  It is RECOMMENDED that
       values are assigned contiguously starting from 1.  The value
       for each profile MUST remain constant at least from one
       re-initialization of the entity's network management system
       to the next re-initialization."
     SYNTAX       Unsigned32 (1..255)
 
   EfmProfileIndexOrZero ::= TEXTUAL-CONVENTION
     DISPLAY-HINT "d"
     STATUS       current
     DESCRIPTION
       "This textual convention is an extension of the
       EfmProfileIndex convention.  The latter defines a greater than
       zero value used to identify a PME profile in the managed EFMCu
       port.  This extension permits the additional value of zero.
       The value of zero is object-specific and MUST therefore be
       defined as part of the description of any object that uses
       this syntax.
       Examples of the usage of zero value might include situations
       where the current operational profile is unknown."
     SYNTAX       Unsigned32 (0..255)
 
   EfmProfileIndexList ::= TEXTUAL-CONVENTION
     DISPLAY-HINT "1d:"
 
 
 
     STATUS       current
     DESCRIPTION
       "This textual convention represents a list of up to 6
       EfmProfileIndex values, any of which can be chosen for
       configuration of a PME in a managed EFMCu port.
       The EfmProfileIndex textual convention defines a greater than
       zero value used to identify a PME profile.
       The value of this object is a concatenation of zero or
       more (up to 6) octets, where each octet contains an 8-bit
       EfmProfileIndex value.
       A zero-length octet string is object-specific and MUST
       therefore be defined as part of the description of any object
       that uses this syntax.  Examples of the usage of a zero-length
       value might include situations where an object using this
       textual convention is irrelevant for a specific EFMCu port
       type."
     SYNTAX       OCTET STRING (SIZE(0..6))
 
   EfmTruthValueOrUnknown ::= TEXTUAL-CONVENTION
     STATUS       current
     DESCRIPTION
       "This textual convention is an extension of the TruthValue
       convention.  The latter defines a boolean value with possible
       values of true(1) and false(2).  This extension permits the
       additional value of unknown(0), which can be returned as the
       result of a GET operation when an exact true or false value
       of the object cannot be determined."
     SYNTAX       INTEGER { unknown(0), true(1), false(2) }
 
  -- Port Notifications Group
 
   efmCuPortNotifications OBJECT IDENTIFIER ::= { efmCuPort 0 }
 
   efmCuLowRateCrossing NOTIFICATION-TYPE
     OBJECTS {
       ifSpeed,
       efmCuThreshLowRate
     }
     STATUS      current
     DESCRIPTION
       "This notification indicates that the EFMCu port's data rate
       has reached/dropped below or exceeded the low rate threshold,
       specified by efmCuThreshLowRate.
 
       This notification MAY be sent for the -O subtype ports
       (2BaseTL-O/10PassTS-O) while the port is Up, on the crossing
       event in both directions: from normal (rate is above the
       threshold) to low (rate equals the threshold or below it) and
 
 
 
       from low to normal.  This notification is not applicable to
       the -R subtypes.
 
       It is RECOMMENDED that a small debouncing period of 2.5 sec,
       between the detection of the condition and the notification,
       is implemented to prevent simultaneous LinkUp/LinkDown and
       efmCuLowRateCrossing notifications to be sent.
 
       The adaptive nature of the EFMCu technology allows the port to
       adapt itself to the changes in the copper environment, e.g.,
       an impulse noise, alien crosstalk, or a micro-interruption may
       temporarily drop one or more PMEs in the aggregation group,
       causing a rate degradation of the aggregated EFMCu link.
       The dropped PMEs would then try to re-initialize, possibly at
       a lower rate than before, adjusting the rate to provide
       required target SNR margin.
 
       Generation of this notification is controlled by the
       efmCuLowRateCrossingEnable object."
     ::= { efmCuPortNotifications 1 }
 
   -- PCS Port group
 
   efmCuPortConfTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF EfmCuPortConfEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Table for Configuration of EFMCu 2BASE-TL/10PASS-TS (PCS)
       Ports.  Entries in this table MUST be maintained in a
       persistent manner."
     ::= { efmCuPort 1 }
 
   efmCuPortConfEntry OBJECT-TYPE
     SYNTAX      EfmCuPortConfEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the EFMCu Port Configuration table.
       Each entry represents an EFMCu port indexed by the ifIndex.
       Note that an EFMCu PCS port runs on top of a single
       or multiple PME port(s), which are also indexed by ifIndex."
     INDEX  { ifIndex }
     ::= { efmCuPortConfTable 1 }
 
   EfmCuPortConfEntry ::=
     SEQUENCE {
       efmCuPAFAdminState               INTEGER,
 
 
 
       efmCuPAFDiscoveryCode            PhysAddress,
       efmCuAdminProfile                EfmProfileIndexList,
       efmCuTargetDataRate              Unsigned32,
       efmCuTargetSnrMgn                Unsigned32,
       efmCuAdaptiveSpectra             TruthValue,
       efmCuThreshLowRate               Unsigned32,
       efmCuLowRateCrossingEnable       TruthValue
     }
 
   efmCuPAFAdminState  OBJECT-TYPE
     SYNTAX      INTEGER {
       enabled(1),
       disabled(2)
     }
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Administrative (desired) state of the PAF of the EFMCu port
       (PCS).
       When 'disabled', PME aggregation will not be performed by the
       PCS.  No more than a single PME can be assigned to this PCS in
       this case.
       When 'enabled', PAF will be performed by the PCS when the link
       is Up, even on a single attached PME, if PAF is supported.
 
       PCS ports incapable of supporting PAF SHALL return a value of
       'disabled'.  Attempts to 'enable' such ports SHALL be
       rejected.
 
       A PAF 'enabled' port with multiple PMEs assigned cannot be
       'disabled'.  Attempts to 'disable' such port SHALL be
       rejected, until at most one PME is left assigned.
 
       Changing PAFAdminState is a traffic-disruptive operation and
       as such SHALL be done when the link is Down.  Attempts to
       change this object SHALL be rejected if the link is Up or
       Initializing.
 
       This object maps to the Clause 30 attribute aPAFAdminState.
 
       If a Clause 45 MDIO Interface to the PCS is present, then this
       object maps to the PAF enable bit in the 10P/2B PCS control
       register.
 
       This object MUST be maintained in a persistent manner."
     REFERENCE
       "[802.3ah] 61.2.2, 45.2.3.18.3"
     ::= { efmCuPortConfEntry 1 }
 
 
 
   efmCuPAFDiscoveryCode  OBJECT-TYPE
     SYNTAX      PhysAddress (SIZE(0|6))
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "PAF Discovery Code of the EFMCu port (PCS).
       A unique 6-octet code used by the Discovery function,
       when PAF is supported.
       PCS ports incapable of supporting PAF SHALL return a
       zero-length octet string on an attempt to read this object.
       An attempt to write to this object SHALL be rejected for such
       ports.
       This object MUST be instantiated for the -O subtype PCS before
       writing operations on the efmCuPAFRemoteDiscoveryCode
       (Set_if_Clear and Clear_if_Same) are performed by PMEs
       associated with the PCS.
       The initial value of this object for -R subtype ports after
       reset is all zeroes.  For -R subtype ports, the value of this
       object cannot be changed directly.  This value may be changed
       as a result of writing operation on the
       efmCuPAFRemoteDiscoveryCode object of remote PME of -O
       subtype, connected to one of the local PMEs associated with
       the PCS.
 
       Discovery MUST be performed when the link is Down.
       Attempts to change this object MUST be rejected (in case of
       SNMP with the error inconsistentValue), if the link is Up or
       Initializing.
 
       The PAF Discovery Code maps to the local Discovery code
       variable in PAF (note that it does not have a corresponding
       Clause 45 register)."
     REFERENCE
       "[802.3ah] 61.2.2.8.3, 61.2.2.8.4, 45.2.6.6.1, 45.2.6.8,
       61A.2"
     ::= { efmCuPortConfEntry 2 }
 
   efmCuAdminProfile  OBJECT-TYPE
     SYNTAX      EfmProfileIndexList
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Desired configuration profile(s), common for all PMEs in the
       EFMCu port.  This object is a list of pointers to entries in
       either efmCuPme2BProfileTable or
       efmCuPme10PProfileTable, depending on the current
       operating SubType of the EFMCu port as indicated by
       efmCuPortSide.
 
 
 
       The value of this object is a list of up to 6 indices of
       profiles.  If this list consists of a single profile index,
       then all PMEs assigned to this EFMCu port SHALL be configured
       according to the profile referenced by that index, unless it
       is overwritten by a corresponding non-zero
       efmCuPmeAdminProfile instance, which takes precedence over
       efmCuAdminProfile.
       A list consisting of more than one index allows each PME
       in the port to be configured according to any profile
       specified in the list.
       By default, this object has a value of 0x01, referencing the
       1st entry in efmCuPme2BProfileTable or
       efmCuPme10PProfileTable.
 
       This object is writable and readable for the -O subtype
       (2BaseTL-O or 10PassTS-O) EFMCu ports.  It is irrelevant for
       the -R  subtype (2BaseTL-R or 10PassTS-R) ports -- a
       zero-length octet string SHALL be returned on an attempt to
       read this object and an attempt to change this object MUST be
       rejected in this case.
 
       Note that the current operational profile value is available
       via the efmCuPmeOperProfile object.
 
       Any modification of this object MUST be performed when the
       link is Down.  Attempts to change this object MUST be
       rejected, if the link is Up or Initializing.
       Attempts to set this object to a list with a member value that
       is not the value of the index for an active entry in the
       corresponding profile table MUST be rejected.
 
       This object maps to the Clause 30 attribute aProfileSelect.
 
       This object MUST be maintained in a persistent manner."
     REFERENCE
       "[802.3ah] 30.11.2.1.6"
     DEFVAL { '01'H }
     ::= { efmCuPortConfEntry 3 }
 
   efmCuTargetDataRate  OBJECT-TYPE
     SYNTAX      Unsigned32(1..100000|999999)
     UNITS       "Kbps"
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Desired EFMCu port 'net' (as seen across MII) Data Rate in
       Kbps, to be achieved during initialization, under spectral
       restrictions placed on each PME via efmCuAdminProfile or
 
 
 
       efmCuPmeAdminProfile, with the desired SNR margin specified by
       efmCuTargetSnrMgn.
       In case of PAF, this object represents a sum of individual PME
       data rates, modified to compensate for fragmentation and
       64/65-octet encapsulation overhead (e.g., target data rate of
       10 Mbps SHALL allow lossless transmission of a full-duplex
       10 Mbps Ethernet frame stream with minimal inter-frame gap).
 
       The value is limited above by 100 Mbps as this is the max
       burst rate across MII for EFMCu ports.
 
       The value between 1 and 100000 indicates that the total data
       rate (ifSpeed) of the EFMCu port after initialization SHALL be
       equal to the target data rate or less, if the target data rate
       cannot be achieved under spectral restrictions specified by
       efmCuAdminProfile/efmCuPmeAdminProfile and with the desired
       SNR margin.  In case the copper environment allows a higher
       total data rate to be achieved than that specified by the
       target, the excess capability SHALL be either converted to
       additional SNR margin or reclaimed by minimizing transmit
       power as controlled by efmCuAdaptiveSpectra.
 
       The value of 999999 means that the target data rate is not
       fixed and SHALL be set to the maximum attainable rate during
       initialization (Best Effort), under specified spectral
       restrictions and with the desired SNR margin.
 
       This object is read-write for the -O subtype EFMCu ports
       (2BaseTL-O/10PassTS-O) and not available for the -R subtypes.
 
       Changing of the Target Data Rate MUST be performed when the
       link is Down.  Attempts to change this object MUST be rejected
       (in case of SNMP with the error inconsistentValue), if the
       link is Up or Initializing.
 
       Note that the current Data Rate of the EFMCu port is
       represented by the ifSpeed object of IF-MIB.
 
       This object MUST be maintained in a persistent manner."
     ::= { efmCuPortConfEntry 4 }
 
   efmCuTargetSnrMgn  OBJECT-TYPE
     SYNTAX      Unsigned32(0..21)
     UNITS       "dB"
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Desired EFMCu port SNR margin to be achieved on all PMEs
 
 
 
       assigned to the port, during initialization. (The SNR margin
       is the difference between the desired SNR and the actual SNR).
 
       Note that 802.3ah recommends using a default target SNR margin
       of 5 dB for 2BASE-TL ports and 6 dB for 10PASS-TS ports in
       order to achieve a mean Bit Error Rate (BER) of 10^-7 at the
       PMA service interface.
 
       This object is read-write for the -O subtype EFMCu ports
       (2BaseTL-O/10PassTS-O) and not available for the -R subtypes.
 
       Changing of the target SNR margin MUST be performed when the
       link is Down.  Attempts to change this object MUST be rejected
       (in case of SNMP with the error inconsistentValue), if the
       link is Up or Initializing.
 
       Note that the current SNR margin of the PMEs comprising the
       EFMCu port is represented by efmCuPmeSnrMgn.
 
       This object MUST be maintained in a persistent manner."
     REFERENCE
       "[802.3ah] 61.1.2"
     ::= { efmCuPortConfEntry 5 }
 
   efmCuAdaptiveSpectra  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Indicates how to utilize excess capacity when the copper
       environment allows a higher total data rate to be achieved
       than that specified by the efmCuTargetDataRate.
 
       A value of true(1) indicates that the excess capability SHALL
       be reclaimed by minimizing transmit power, e.g., using higher
       constellations and Power Back-Off, in order to reduce
       interference to other copper pairs in the binder and the
       adverse impact to link/system performance.
 
       A value of false(2) indicates that the excess capability SHALL
       be converted to additional SNR margin and spread evenly across
       all active PMEs assigned to the (PCS) port, to increase link
       robustness.
 
       This object is read-write for the -O subtype EFMCu ports
       (2BaseTL-O/10PassTS-O) and not available for the -R subtypes.
 
       Changing of this object MUST be performed when the link is
 
 
 
       Down.  Attempts to change this object MUST be rejected (in
       case of SNMP with the error inconsistentValue), if the link
       is Up or Initializing.
 
       This object MUST be maintained in a persistent manner."
     ::= { efmCuPortConfEntry 6 }
 
   efmCuThreshLowRate  OBJECT-TYPE
     SYNTAX      Unsigned32(1..100000)
     UNITS       "Kbps"
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "This object configures the EFMCu port low-rate crossing alarm
       threshold.  When the current value of ifSpeed for this port
       reaches/drops below or exceeds this threshold, an
       efmCuLowRateCrossing notification MAY be generated if enabled
       by efmCuLowRateCrossingEnable.
 
       This object is read-write for the -O subtype EFMCu ports
       (2BaseTL-O/10PassTS-O) and not available for the -R subtypes.
 
       This object MUST be maintained in a persistent manner."
     ::= { efmCuPortConfEntry 7 }
 
   efmCuLowRateCrossingEnable  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Indicates whether efmCuLowRateCrossing notifications should
       be generated for this interface.
 
       A value of true(1) indicates that efmCuLowRateCrossing
       notification is enabled.  A value of false(2) indicates that
       the notification is disabled.
 
       This object is read-write for the -O subtype EFMCu ports
       (2BaseTL-O/10PassTS-O) and not available for the -R subtypes.
 
       This object MUST be maintained in a persistent manner."
     ::= { efmCuPortConfEntry 8 }
 
 
   efmCuPortCapabilityTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF EfmCuPortCapabilityEntry
     MAX-ACCESS  not-accessible
     STATUS      current
 
 
 
     DESCRIPTION
       "Table for Capabilities of EFMCu 2BASE-TL/10PASS-TS (PCS)
       Ports.  Entries in this table MUST be maintained in a
       persistent manner"
     ::= { efmCuPort 2 }
 
   efmCuPortCapabilityEntry OBJECT-TYPE
     SYNTAX      EfmCuPortCapabilityEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the EFMCu Port Capability table.
       Each entry represents an EFMCu port indexed by the ifIndex.
       Note that an EFMCu PCS port runs on top of a single
       or multiple PME port(s), which are also indexed by ifIndex."
     INDEX  { ifIndex }
     ::= { efmCuPortCapabilityTable 1 }
 
   EfmCuPortCapabilityEntry ::=
     SEQUENCE {
       efmCuPAFSupported                TruthValue,
       efmCuPeerPAFSupported            EfmTruthValueOrUnknown,
       efmCuPAFCapacity                 Unsigned32,
       efmCuPeerPAFCapacity             Unsigned32
     }
 
   efmCuPAFSupported  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "PME Aggregation Function (PAF) capability of the EFMCu port
       (PCS).
       This object has a value of true(1) when the PCS can perform
       PME aggregation on the available PMEs.
       Ports incapable of PAF SHALL return a value of false(2).
 
       This object maps to the Clause 30 attribute aPAFSupported.
 
       If a Clause 45 MDIO Interface to the PCS is present,
       then this object maps to the PAF available bit in the
       10P/2B capability register."
     REFERENCE
       "[802.3ah] 61.2.2, 30.11.1.1.4, 45.2.3.17.1"
     ::= { efmCuPortCapabilityEntry 1 }
 
   efmCuPeerPAFSupported  OBJECT-TYPE
     SYNTAX      EfmTruthValueOrUnknown
 
 
 
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "PME Aggregation Function (PAF) capability of the EFMCu port
       (PCS) link partner.
       This object has a value of true(1) when the remote PCS can
       perform PME aggregation on its available PMEs.
       Ports whose peers are incapable of PAF SHALL return a value
       of false(2).
       Ports whose peers cannot be reached because of the link
       state SHALL return a value of unknown(0).
 
       This object maps to the Clause 30 attribute
       aRemotePAFSupported.
 
       If a Clause 45 MDIO Interface to the PCS is present, then
       this object maps to the Remote PAF supported bit in the
       10P/2B capability register."
     REFERENCE
       "[802.3ah] 61.2.2, 30.11.1.1.9, 45.2.3.17.2"
     ::= { efmCuPortCapabilityEntry 2 }
 
   efmCuPAFCapacity  OBJECT-TYPE
     SYNTAX      Unsigned32 (1..32)
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "Number of PMEs that can be aggregated by the local PAF.
       The number of PMEs currently assigned to a particular
       EFMCu port (efmCuNumPMEs) is never greater than
       efmCuPAFCapacity.
 
       This object maps to the Clause 30 attribute
       aLocalPAFCapacity."
     REFERENCE
       "[802.3ah] 61.2.2, 30.11.1.1.6"
     ::= { efmCuPortCapabilityEntry 3 }
 
   efmCuPeerPAFCapacity  OBJECT-TYPE
     SYNTAX      Unsigned32 (0|1..32)
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "Number of PMEs that can be aggregated by the PAF of the peer
       PHY (PCS port).
       A value of 0 is returned when peer PAF capacity is unknown
       (peer cannot be reached).
 
 
 
 
       This object maps to the Clause 30 attribute
       aRemotePAFCapacity."
     REFERENCE
       "[802.3ah] 61.2.2, 30.11.1.1.10"
     ::= { efmCuPortCapabilityEntry 4 }
 
   efmCuPortStatusTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF EfmCuPortStatusEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table provides overall status information of EFMCu
       2BASE-TL/10PASS-TS ports, complementing the generic status
       information from the ifTable of IF-MIB and ifMauTable of
       MAU-MIB.  Additional status information about connected PMEs
       is available from the efmCuPmeStatusTable.
 
       This table contains live data from the equipment.  As such,
       it is NOT persistent."
     ::= { efmCuPort 3 }
 
   efmCuPortStatusEntry OBJECT-TYPE
     SYNTAX      EfmCuPortStatusEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the EFMCu Port Status table.
       Each entry represents an EFMCu port indexed by the ifIndex.
       Note that an EFMCu PCS port runs on top of a single
       or multiple PME port(s), which are also indexed by ifIndex."
     INDEX  { ifIndex }
     ::= { efmCuPortStatusTable 1 }
 
   EfmCuPortStatusEntry ::=
     SEQUENCE {
       efmCuFltStatus                   BITS,
       efmCuPortSide                    INTEGER,
       efmCuNumPMEs                     Unsigned32,
       efmCuPAFInErrors                 Counter32,
       efmCuPAFInSmallFragments         Counter32,
       efmCuPAFInLargeFragments         Counter32,
       efmCuPAFInBadFragments           Counter32,
       efmCuPAFInLostFragments          Counter32,
       efmCuPAFInLostStarts             Counter32,
       efmCuPAFInLostEnds               Counter32,
       efmCuPAFInOverflows              Counter32
     }
 
 
 
 
   efmCuFltStatus  OBJECT-TYPE
     SYNTAX      BITS {
       noPeer(0),
       peerPowerLoss(1),
       pmeSubTypeMismatch(2),
       lowRate(3)
     }
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "EFMCu (PCS) port Fault Status.  This is a bitmap of possible
       conditions.  The various bit positions are:
         noPeer              - the peer PHY cannot be reached (e.g.,
                               no PMEs attached, all PMEs are Down,
                               etc.). More info is available in
                               efmCuPmeFltStatus.
         peerPowerLoss       - the peer PHY has indicated impending
                               unit failure due to loss of local
                               power ('Dying Gasp').
         pmeSubTypeMismatch  - local PMEs in the aggregation group
                               are not of the same subtype, e.g.,
                               some PMEs in the local device are -O
                               while others are -R subtype.
         lowRate             - ifSpeed of the port reached or dropped
                               below efmCuThreshLowRate.
 
       This object is intended to supplement the ifOperStatus object
       in IF-MIB and ifMauMediaAvailable in MAU-MIB.
 
       Additional information is available via the efmCuPmeFltStatus
       object for each PME in the aggregation group (single PME if
       PAF is disabled)."
     REFERENCE
       "IF-MIB, ifOperStatus; MAU-MIB, ifMauMediaAvailable;
        efmCuPmeFltStatus"
     ::= { efmCuPortStatusEntry 1 }
 
   efmCuPortSide  OBJECT-TYPE
     SYNTAX      INTEGER {
       subscriber(1),
       office(2),
       unknown(3)
     }
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "EFM port mode of operation (subtype).
       The value of 'subscriber' indicates that the port is
 
 
 
       designated as '-R' subtype (all PMEs assigned to this port are
       of subtype '-R').
       The value of the 'office' indicates that the port is
       designated as '-O' subtype (all PMEs assigned to this port are
       of subtype '-O').
       The value of 'unknown' indicates that the port has no assigned
       PMEs yet or that the assigned PMEs are not of the same side
       (subTypePMEMismatch).
 
       This object partially maps to the Clause 30 attribute
       aPhyEnd."
     REFERENCE
        "[802.3ah] 61.1, 30.11.1.1.2"
     ::= { efmCuPortStatusEntry 2 }
 
   efmCuNumPMEs  OBJECT-TYPE
     SYNTAX      Unsigned32 (0..32)
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of PMEs that is currently aggregated by the local
       PAF (assigned to the EFMCu port using the ifStackTable).
       This number is never greater than efmCuPAFCapacity.
 
       This object SHALL be automatically incremented or decremented
       when a PME is added or deleted to/from the EFMCu port using
       the ifStackTable."
     REFERENCE
       "[802.3ah] 61.2.2, 30.11.1.1.6"
     ::= { efmCuPortStatusEntry 3 }
 
   efmCuPAFInErrors OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of fragments that have been received across the
       gamma interface with RxErr asserted and discarded.
       This read-only counter is inactive (not incremented) when the
       PAF is unsupported or disabled.  Upon disabling the PAF, the
       counter retains its previous value.
 
       If a Clause 45 MDIO Interface to the PCS is present, then
       this object maps to the 10P/2B PAF RX error register.
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
 
 
 
       defined in IF-MIB."
     REFERENCE
       "[802.3ah] 45.2.3.21"
     ::= { efmCuPortStatusEntry 4 }
 
   efmCuPAFInSmallFragments OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of fragments smaller than minFragmentSize
       (64 bytes) that have been received across the gamma interface
       and discarded.
       This read-only counter is inactive when the PAF is
       unsupported or disabled.  Upon disabling the PAF, the counter
       retains its previous value.
 
       If a Clause 45 MDIO Interface to the PCS is present, then
       this object maps to the 10P/2B PAF small fragments register.
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB."
     REFERENCE
       "[802.3ah] 45.2.3.22"
     ::= { efmCuPortStatusEntry 5 }
 
   efmCuPAFInLargeFragments OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of fragments larger than maxFragmentSize
       (512 bytes) that have been received across the gamma interface
       and discarded.
       This read-only counter is inactive when the PAF is
       unsupported or disabled.  Upon disabling the PAF, the counter
       retains its previous value.
 
       If a Clause 45 MDIO Interface to the PCS is present, then
       this object maps to the 10P/2B PAF large fragments register.
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB."
     REFERENCE
 
 
 
       "[802.3ah] 45.2.3.23"
     ::= { efmCuPortStatusEntry 6 }
 
   efmCuPAFInBadFragments OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of fragments that do not fit into the sequence
       expected by the frame assembly function and that have been
       received across the gamma interface and discarded (the
       frame buffer is flushed to the next valid frame start).
       This read-only counter is inactive when the PAF is
       unsupported or disabled.  Upon disabling the PAF, the counter
       retains its previous value.
 
       If a Clause 45 MDIO Interface to the PCS is present, then
       this object maps to the 10P/2B PAF bad fragments register.
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB."
     REFERENCE
       "[802.3ah] 45.2.3.25"
     ::= { efmCuPortStatusEntry 7 }
 
   efmCuPAFInLostFragments OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of gaps in the sequence of fragments that have
       been received across the gamma interface (the frame buffer is
       flushed to the next valid frame start, when fragment/fragments
       expected by the frame assembly function is/are not received).
       This read-only counter is inactive when the PAF is
       unsupported or disabled.  Upon disabling the PAF, the counter
       retains its previous value.
 
       If a Clause 45 MDIO Interface to the PCS is present, then
       this object maps to the 10P/2B PAF lost fragment register.
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB."
     REFERENCE
 
 
 
       "[802.3ah] 45.2.3.26"
     ::= { efmCuPortStatusEntry 8 }
 
   efmCuPAFInLostStarts OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of missing StartOfPacket indicators expected by
       the frame assembly function.
       This read-only counter is inactive when the PAF is
       unsupported or disabled.  Upon disabling the PAF, the counter
       retains its previous value.
 
       If a Clause 45 MDIO Interface to the PCS is present, then
       this object maps to the 10P/2B PAF lost start of fragment
       register.
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB."
     REFERENCE
       "[802.3ah] 45.2.3.27"
     ::= { efmCuPortStatusEntry 9 }
 
   efmCuPAFInLostEnds OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of missing EndOfPacket indicators expected by the
       frame assembly function.
       This read-only counter is inactive when the PAF is
       unsupported or disabled.  Upon disabling the PAF, the counter
       retains its previous value.
 
       If a Clause 45 MDIO Interface to the PCS is present, then
       this object maps to the 10P/2B PAF lost start of fragment
       register.
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB."
     REFERENCE
       "[802.3ah] 45.2.3.28"
     ::= { efmCuPortStatusEntry 10 }
 
 
 
   efmCuPAFInOverflows OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of fragments, received across the gamma interface
       and discarded, which would have caused the frame assembly
       buffer to overflow.
       This read-only counter is inactive when the PAF is
       unsupported or disabled.  Upon disabling the PAF, the counter
       retains its previous value.
 
       If a Clause 45 MDIO Interface to the PCS is present, then
       this object maps to the 10P/2B PAF overflow register.
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB."
     REFERENCE
       "[802.3ah] 45.2.3.24"
     ::= { efmCuPortStatusEntry 11 }
 
  -- PME Notifications Group
 
   efmCuPmeNotifications OBJECT IDENTIFIER ::= { efmCuPme 0 }
 
   efmCuPmeLineAtnCrossing NOTIFICATION-TYPE
     OBJECTS {
       efmCuPmeLineAtn,
       efmCuPmeThreshLineAtn
     }
     STATUS      current
     DESCRIPTION
       "This notification indicates that the loop attenuation
       threshold (as per the efmCuPmeThreshLineAtn
       value) has been reached/exceeded for the 2BASE-TL/10PASS-TS
       PME.  This notification MAY be sent on the crossing event in
       both directions: from normal to exceeded and from exceeded
       to normal.
 
       It is RECOMMENDED that a small debouncing period of 2.5 sec,
       between the detection of the condition and the notification,
       is implemented to prevent intermittent notifications from
       being sent.
 
       Generation of this notification is controlled by the
       efmCuPmeLineAtnCrossingEnable object."
 
 
 
     ::= { efmCuPmeNotifications 1 }
 
   efmCuPmeSnrMgnCrossing NOTIFICATION-TYPE
     OBJECTS {
       efmCuPmeSnrMgn,
       efmCuPmeThreshSnrMgn
     }
     STATUS      current
     DESCRIPTION
       "This notification indicates that the SNR margin threshold
       (as per the efmCuPmeThreshSnrMgn value) has been
       reached/exceeded for the 2BASE-TL/10PASS-TS PME.
       This notification MAY be sent on the crossing event in
       both directions: from normal to exceeded and from exceeded
       to normal.
 
       It is RECOMMENDED that a small debouncing period of 2.5 sec,
       between the detection of the condition and the notification,
       is implemented to prevent intermittent notifications from
       being sent.
 
       Generation of this notification is controlled by the
       efmCuPmeSnrMgnCrossingEnable object."
     ::= { efmCuPmeNotifications 2 }
 
   efmCuPmeDeviceFault NOTIFICATION-TYPE
     OBJECTS {
       efmCuPmeFltStatus
     }
     STATUS      current
     DESCRIPTION
       "This notification indicates that a fault in the PME has been
       detected by a vendor-specific diagnostic or a self-test.
 
       Generation of this notification is controlled by the
       efmCuPmeDeviceFaultEnable object."
     ::= { efmCuPmeNotifications 3 }
 
   efmCuPmeConfigInitFailure NOTIFICATION-TYPE
     OBJECTS {
       efmCuPmeFltStatus,
       efmCuAdminProfile,
       efmCuPmeAdminProfile
     }
     STATUS      current
     DESCRIPTION
       "This notification indicates that PME initialization has
       failed, due to inability of the PME link to achieve the
 
 
 
       requested configuration profile.
 
       Generation of this notification is controlled by the
       efmCuPmeConfigInitFailEnable object."
     ::= { efmCuPmeNotifications 4 }
 
   efmCuPmeProtocolInitFailure NOTIFICATION-TYPE
     OBJECTS {
       efmCuPmeFltStatus,
       efmCuPmeOperSubType
     }
     STATUS     current
     DESCRIPTION
       "This notification indicates that the peer PME was using
       an incompatible protocol during initialization.
 
       Generation of this notification is controlled by the
       efmCuPmeProtocolInitFailEnable object."
     ::= { efmCuPmeNotifications 5 }
 
   -- The PME group
 
   efmCuPmeConfTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF EfmCuPmeConfEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Table for Configuration of common aspects for EFMCu
       2BASE-TL/10PASS-TS PME ports (modems).  Configuration of
       aspects specific to 2BASE-TL or 10PASS-TS PME types is
       represented in efmCuPme2BConfTable and efmCuPme10PConfTable,
       respectively.
 
       Entries in this table MUST be maintained in a persistent
       manner."
     ::= { efmCuPme 1 }
 
   efmCuPmeConfEntry OBJECT-TYPE
     SYNTAX      EfmCuPmeConfEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the EFMCu PME Configuration table.
       Each entry represents common aspects of an EFMCu PME port
       indexed by the ifIndex.  Note that an EFMCu PME port can be
       stacked below a single PCS port, also indexed by ifIndex,
       possibly together with other PME ports if PAF is enabled."
     INDEX  { ifIndex }
 
 
 
     ::= { efmCuPmeConfTable 1 }
 
   EfmCuPmeConfEntry ::=
     SEQUENCE {
       efmCuPmeAdminSubType           INTEGER,
       efmCuPmeAdminProfile           EfmProfileIndexOrZero,
       efmCuPAFRemoteDiscoveryCode    PhysAddress,
       efmCuPmeThreshLineAtn          Integer32,
       efmCuPmeThreshSnrMgn           Integer32,
       efmCuPmeLineAtnCrossingEnable  TruthValue,
       efmCuPmeSnrMgnCrossingEnable   TruthValue,
       efmCuPmeDeviceFaultEnable      TruthValue,
       efmCuPmeConfigInitFailEnable   TruthValue,
       efmCuPmeProtocolInitFailEnable TruthValue
     }
 
   efmCuPmeAdminSubType  OBJECT-TYPE
     SYNTAX      INTEGER {
       ieee2BaseTLO(1),
       ieee2BaseTLR(2),
       ieee10PassTSO(3),
       ieee10PassTSR(4),
       ieee2BaseTLor10PassTSR(5),
       ieee2BaseTLor10PassTSO(6),
       ieee10PassTSor2BaseTLO(7)
     }
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Administrative (desired) subtype of the PME.
       Possible values are:
         ieee2BaseTLO           - PME SHALL operate as 2BaseTL-O
         ieee2BaseTLR           - PME SHALL operate as 2BaseTL-R
         ieee10PassTSO          - PME SHALL operate as 10PassTS-O
         ieee10PassTSR          - PME SHALL operate as 10PassTS-R
         ieee2BaseTLor10PassTSR - PME SHALL operate as 2BaseTL-R or
                                  10PassTS-R.  The actual value will
                                  be set by the -O link partner
                                  during initialization (handshake).
         ieee2BaseTLor10PassTSO - PME SHALL operate as 2BaseTL-O
                                  (preferred) or 10PassTS-O.  The
                                  actual value will be set during
                                  initialization depending on the -R
                                  link partner capability (i.e., if
                                  -R is incapable of the preferred
                                  2BaseTL mode, 10PassTS will be
                                  used).
         ieee10PassTSor2BaseTLO - PME SHALL operate as 10PassTS-O
 
 
 
                                  (preferred) or 2BaseTL-O.  The
                                  actual value will be set during
                                  initialization depending on the -R
                                  link partner capability (i.e., if
                                  -R is incapable of the preferred
                                  10PassTS mode, 2BaseTL will be
                                  used).
 
       Changing efmCuPmeAdminSubType is a traffic-disruptive
       operation and as such SHALL be done when the link is Down.
       Attempts to change this object SHALL be rejected if the link
       is Up or Initializing.
       Attempts to change this object to an unsupported subtype
       (see efmCuPmeSubTypesSupported) SHALL be rejected.
 
       The current operational subtype is indicated by the
       efmCuPmeOperSubType variable.
 
       If a Clause 45 MDIO Interface to the PMA/PMD is present, then
       this object combines values of the Port subtype select bits
       and the PMA/PMD type selection bits in the 10P/2B PMA/PMD
       control register."
     REFERENCE
       "[802.3ah] 61.1, 45.2.1.11.4, 45.2.1.11.7"
     ::= { efmCuPmeConfEntry 1 }
 
   efmCuPmeAdminProfile  OBJECT-TYPE
     SYNTAX      EfmProfileIndexOrZero
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Desired PME configuration profile.  This object is a pointer
       to an entry in either the efmCuPme2BProfileTable or the
       efmCuPme10PProfileTable, depending on the current operating
       SubType of the PME.  The value of this object is the index of
       the referenced profile.
       The value of zero (default) indicates that the PME is
       configured via the efmCuAdminProfile object for the PCS port
       to which this PME is assigned.  That is, the profile
       referenced by efmCuPmeAdminProfile takes precedence
       over the profile(s) referenced by efmCuAdminProfile.
 
       This object is writable and readable for the CO subtype PMEs
       (2BaseTL-O or 10PassTS-O). It is irrelevant for the CPE
       subtype (2BaseTL-R or 10PassTS-R) -- a zero value SHALL be
       returned on an attempt to read this object and any attempt
       to change this object MUST be rejected in this case.
 
 
 
 
       Note that the current operational profile value is available
       via efmCuPmeOperProfile object.
 
       Any modification of this object MUST be performed when the
       link is Down.  Attempts to change this object MUST be
       rejected, if the link is Up or Initializing.
 
       Attempts to set this object to a value that is not the value
       of the index for an active entry in the corresponding profile
       table MUST be rejected.
 
       This object maps to the Clause 30 attribute aProfileSelect.
 
       This object MUST be maintained in a persistent manner."
     REFERENCE
       "[802.3ah] 30.11.2.1.6"
     DEFVAL { 0 }
     ::= { efmCuPmeConfEntry 2 }
 
   efmCuPAFRemoteDiscoveryCode  OBJECT-TYPE
     SYNTAX      PhysAddress (SIZE(0|6))
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "PAF Remote Discovery Code of the PME port at the CO.
       The 6-octet Discovery Code of the peer PCS connected via
       the PME.
       Reading this object results in a Discovery Get operation.
       Setting this object to all zeroes results in a Discovery
       Clear_if_Same operation (the value of efmCuPAFDiscoveryCode
       at the peer PCS SHALL be the same as efmCuPAFDiscoveryCode of
       the local PCS associated with the PME for the operation to
       succeed).
       Writing a non-zero value to this object results in a
       Discovery Set_if_Clear operation.
       A zero-length octet string SHALL be returned on an attempt to
       read this object when PAF aggregation is not enabled.
 
       This object is irrelevant in CPE port (-R) subtypes: in this
       case, a zero-length octet string SHALL be returned on an
       attempt to read this object; writing to this object SHALL
       be rejected.
 
       Discovery MUST be performed when the link is Down.
       Attempts to change this object MUST be rejected (in case of
       SNMP with the error inconsistentValue), if the link is Up or
       Initializing.
 
 
 
 
       If a Clause 45 MDIO Interface to the PMA/PMD is present, then
       this object is a function of 10P/2B aggregation discovery
       control register, Discovery operation result bits in 10P/2B
       aggregation and discovery status register and
       10P/2B aggregation discovery code register."
     REFERENCE
       "[802.3ah] 61.2.2.8.4, 45.2.6.6-45.2.6.8"
     ::= { efmCuPmeConfEntry 3 }
 
   efmCuPmeThreshLineAtn  OBJECT-TYPE
     SYNTAX  Integer32(-127..128)
     UNITS       "dB"
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Desired Line Attenuation threshold for the 2B/10P PME.
       This object configures the line attenuation alarm threshold.
       When the current value of Line Attenuation reaches or
       exceeds this threshold, an efmCuPmeLineAtnCrossing
       notification MAY be generated, if enabled by
       efmCuPmeLineAtnCrossingEnable.
 
       This object is writable for the CO subtype PMEs (-O).
       It is read-only for the CPE subtype (-R).
 
       Changing of the Line Attenuation threshold MUST be performed
       when the link is Down.  Attempts to change this object MUST be
       rejected (in case of SNMP with the error inconsistentValue),
       if the link is Up or Initializing.
 
       If a Clause 45 MDIO Interface to the PME is present, then this
       object maps to the loop attenuation threshold bits in
       the 2B PMD line quality thresholds register."
     REFERENCE
       "[802.3ah] 45.2.1.36"
     ::= { efmCuPmeConfEntry 4 }
 
   efmCuPmeThreshSnrMgn  OBJECT-TYPE
     SYNTAX      Integer32(-127..128)
     UNITS       "dB"
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Desired SNR margin threshold for the 2B/10P PME.
       This object configures the SNR margin alarm threshold.
       When the current value of SNR margin reaches or exceeds this
       threshold, an efmCuPmeSnrMgnCrossing notification MAY be
       generated, if enabled by efmCuPmeSnrMgnCrossingEnable.
 
 
 
       This object is writable for the CO subtype PMEs
       (2BaseTL-O/10PassTS-O).  It is read-only for the CPE subtype
       (2BaseTL-R/10PassTS-R).
 
       Changing of the SNR margin threshold MUST be performed when
       the link is Down.  Attempts to change this object MUST be
       rejected (in case of SNMP with the error inconsistentValue),
       if the link is Up or Initializing.
 
       If a Clause 45 MDIO Interface to the PME is present, then this
       object maps to the SNR margin threshold bits in the 2B PMD
       line quality thresholds register."
     REFERENCE
       "[802.3ah] 45.2.1.36"
     ::= { efmCuPmeConfEntry 5 }
 
   efmCuPmeLineAtnCrossingEnable  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Indicates whether efmCuPmeLineAtnCrossing notifications
       should be generated for this interface.
 
       A value of true(1) indicates that efmCuPmeLineAtnCrossing
       notification is enabled.  A value of false(2) indicates that
       the notification is disabled."
     ::= { efmCuPmeConfEntry 6 }
 
   efmCuPmeSnrMgnCrossingEnable  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Indicates whether efmCuPmeSnrMgnCrossing notifications
       should be generated for this interface.
 
       A value of true(1) indicates that efmCuPmeSnrMgnCrossing
       notification is enabled.  A value of false(2) indicates that
       the notification is disabled."
     ::= { efmCuPmeConfEntry 7 }
 
   efmCuPmeDeviceFaultEnable  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Indicates whether efmCuPmeDeviceFault notifications
 
 
 
       should be generated for this interface.
 
       A value of true(1) indicates that efmCuPmeDeviceFault
       notification is enabled.  A value of false(2) indicates that
       the notification is disabled."
     ::= { efmCuPmeConfEntry 8 }
 
   efmCuPmeConfigInitFailEnable  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Indicates whether efmCuPmeConfigInitFailure notifications
       should be generated for this interface.
 
       A value of true(1) indicates that efmCuPmeConfigInitFailure
       notification is enabled.  A value of false(2) indicates that
       the notification is disabled."
     ::= { efmCuPmeConfEntry 9 }
 
   efmCuPmeProtocolInitFailEnable  OBJECT-TYPE
     SYNTAX      TruthValue
     MAX-ACCESS  read-write
     STATUS      current
     DESCRIPTION
       "Indicates whether efmCuPmeProtocolInitFailure notifications
       should be generated for this interface.
 
       A value of true(1) indicates that efmCuPmeProtocolInitFailure
       notification is enabled.  A value of false(2) indicates that
       the notification is disabled."
     ::= { efmCuPmeConfEntry 10 }
 
 
   efmCuPmeCapabilityTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF EfmCuPmeCapabilityEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Table for the configuration of common aspects for EFMCu
       2BASE-TL/10PASS-TS PME ports (modems).  The configuration of
       aspects specific to 2BASE-TL or 10PASS-TS PME types is
       represented in the efmCuPme2BConfTable and the
       efmCuPme10PConfTable, respectively.
 
       Entries in this table MUST be maintained in a persistent
       manner."
     ::= { efmCuPme 2 }
 
 
 
   efmCuPmeCapabilityEntry OBJECT-TYPE
     SYNTAX      EfmCuPmeCapabilityEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the EFMCu PME Capability table.
       Each entry represents common aspects of an EFMCu PME port
       indexed by the ifIndex.  Note that an EFMCu PME port can be
       stacked below a single PCS port, also indexed by ifIndex,
       possibly together with other PME ports if PAF is enabled."
     INDEX  { ifIndex }
     ::= { efmCuPmeCapabilityTable 1 }
 
   EfmCuPmeCapabilityEntry ::=
     SEQUENCE {
       efmCuPmeSubTypesSupported     BITS
     }
 
   efmCuPmeSubTypesSupported  OBJECT-TYPE
     SYNTAX      BITS {
       ieee2BaseTLO(0),
       ieee2BaseTLR(1),
       ieee10PassTSO(2),
       ieee10PassTSR(3)
     }
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "PME supported subtypes.  This is a bitmap of possible
       subtypes.  The various bit positions are:
         ieee2BaseTLO    - PME is capable of operating as 2BaseTL-O
         ieee2BaseTLR    - PME is capable of operating as 2BaseTL-R
         ieee10PassTSO   - PME is capable of operating as 10PassTS-O
         ieee10PassTSR   - PME is capable of operating as 10PassTS-R
 
       The desired mode of operation is determined by
       efmCuPmeAdminSubType, while efmCuPmeOperSubType reflects the
       current operating mode.
 
       If a Clause 45 MDIO Interface to the PCS is present, then this
       object combines the 10PASS-TS capable and 2BASE-TL capable
       bits in the 10P/2B PMA/PMD speed ability register and the
       CO supported and CPE supported bits in the 10P/2B PMA/PMD
       status register."
     REFERENCE
       "[802.3ah] 61.1, 45.2.1.4.1, 45.2.1.4.2, 45.2.1.12.2,
       45.2.1.12.3"
     ::= { efmCuPmeCapabilityEntry 1 }
 
 
 
   efmCuPmeStatusTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF EfmCuPmeStatusEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table provides common status information of EFMCu
       2BASE-TL/10PASS-TS PME ports.  Status information specific
       to 10PASS-TS PME is represented in efmCuPme10PStatusTable.
 
       This table contains live data from the equipment.  As such,
       it is NOT persistent."
     ::= { efmCuPme 3 }
 
   efmCuPmeStatusEntry OBJECT-TYPE
     SYNTAX      EfmCuPmeStatusEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the EFMCu PME Status table.
       Each entry represents common aspects of an EFMCu PME port
       indexed by the ifIndex.  Note that an EFMCu PME port can be
       stacked below a single PCS port, also indexed by ifIndex,
       possibly together with other PME ports if PAF is enabled."
     INDEX  { ifIndex }
     ::= { efmCuPmeStatusTable 1 }
 
   EfmCuPmeStatusEntry ::=
     SEQUENCE {
       efmCuPmeOperStatus            INTEGER,
       efmCuPmeFltStatus             BITS,
       efmCuPmeOperSubType           INTEGER,
       efmCuPmeOperProfile           EfmProfileIndexOrZero,
       efmCuPmeSnrMgn                Integer32,
       efmCuPmePeerSnrMgn            Integer32,
       efmCuPmeLineAtn               Integer32,
       efmCuPmePeerLineAtn           Integer32,
       efmCuPmeEquivalentLength      Unsigned32,
       efmCuPmeTCCodingErrors        Counter32,
       efmCuPmeTCCrcErrors           Counter32
     }
 
   efmCuPmeOperStatus  OBJECT-TYPE
     SYNTAX      INTEGER {
       up(1),
       downNotReady(2),
       downReady(3),
       init(4)
     }
 
 
 
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "Current PME link Operational Status.  Possible values are:
         up(1)           - The link is Up and ready to pass
                           64/65-octet encoded frames or fragments.
         downNotReady(2) - The link is Down and the PME does not
                           detect Handshake tones from its peer.
                           This value may indicate a possible
                           problem with the peer PME.
         downReady(3)    - The link is Down and the PME detects
                           Handshake tones from its peer.
         init(4)         - The link is Initializing, as a result of
                           ifAdminStatus being set to 'up' for a
                           particular PME or a PCS to which the PME
                           is connected.
 
       This object is intended to supplement the Down(2) state of
       ifOperStatus.
 
       This object partially maps to the Clause 30 attribute
       aPMEStatus.
 
       If a Clause 45 MDIO Interface to the PME is present, then this
       object partially maps to PMA/PMD link status bits in 10P/2B
       PMA/PMD status register."
     REFERENCE
       "[802.3ah] 30.11.2.1.3, 45.2.1.12.4"
     ::= { efmCuPmeStatusEntry 1 }
 
   efmCuPmeFltStatus  OBJECT-TYPE
     SYNTAX      BITS {
       lossOfFraming(0),
       snrMgnDefect(1),
       lineAtnDefect(2),
       deviceFault(3),
       configInitFailure(4),
       protocolInitFailure(5)
     }
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "Current/Last PME link Fault Status.  This is a bitmap of
       possible conditions.  The various bit positions are:
 
         lossOfFraming       - Loss of Framing for 10P or
                               Loss of Sync word for 2B PMD or
                               Loss of 64/65-octet framing.
 
 
 
         snrMgnDefect        - SNR margin dropped below the
                               threshold.
         lineAtnDefect       - Line Attenuation exceeds the
                               threshold.
         deviceFault         - Indicates a vendor-dependent
                               diagnostic or self-test fault
                               has been detected.
         configInitFailure   - Configuration initialization failure,
                               due to inability of the PME link to
                               support the configuration profile,
                               requested during initialization.
         protocolInitFailure - Protocol initialization failure, due
                               to an incompatible protocol used by
                               the peer PME during init (that could
                               happen if a peer PMD is a regular
                               G.SDHSL/VDSL modem instead of a
                               2BASE-TL/10PASS-TS PME).
 
       This object is intended to supplement ifOperStatus in IF-MIB.
 
       This object holds information about the last fault.
       efmCuPmeFltStatus is cleared by the device restart.
       In addition, lossOfFraming, configInitFailure, and
       protocolInitFailure are cleared by PME init;
       deviceFault is cleared by successful diagnostics/test;
       snrMgnDefect and lineAtnDefect are cleared by SNR margin
       and Line attenuation, respectively, returning to norm and by
       PME init.
 
       This object partially maps to the Clause 30 attribute
       aPMEStatus.
 
       If a Clause 45 MDIO Interface to the PME is present, then this
       object consolidates information from various PMA/PMD
       registers, namely: Fault bit in PMA/PMD status 1 register,
       10P/2B PMA/PMD link loss register,
       10P outgoing indicator bits status register,
       10P incoming indicator bits status register,
       2B state defects register."
     REFERENCE
       "[802.3ah] 30.11.2.1.3, 45.2.1.2.1, 45.2.1.38,
       45.2.1.39, 45.2.1.54"
     ::= { efmCuPmeStatusEntry 2 }
 
   efmCuPmeOperSubType  OBJECT-TYPE
     SYNTAX      INTEGER {
       ieee2BaseTLO(1),
       ieee2BaseTLR(2),
 
 
 
       ieee10PassTSO(3),
       ieee10PassTSR(4)
     }
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "Current operational subtype of the PME.
       Possible values are:
         ieee2BaseTLO           - PME operates as 2BaseTL-O
         ieee2BaseTLR           - PME operates as 2BaseTL-R
         ieee10PassTSO          - PME operates as 10PassTS-O
         ieee10PassTSR          - PME operates as 10PassTS-R
 
       The desired operational subtype of the PME can be configured
       via the efmCuPmeAdminSubType variable.
 
       If a Clause 45 MDIO Interface to the PMA/PMD is present, then
       this object combines values of the Port subtype select
       bits, the PMA/PMD type selection bits in the 10P/2B
       PMA/PMD control register, and the PMA/PMD link status bits in
       the 10P/2B PMA/PMD status register."
     REFERENCE
       "[802.3ah] 61.1, 45.2.1.11.4, 45.2.1.11.7, 45.2.1.12.4"
     ::= { efmCuPmeStatusEntry 3 }
 
   efmCuPmeOperProfile  OBJECT-TYPE
     SYNTAX      EfmProfileIndexOrZero
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "PME current operating profile.  This object is a pointer to
       an entry in either the efmCuPme2BProfileTable or the
       efmCuPme10PProfileTable, depending on the current operating
       SubType of the PME as indicated by efmCuPmeOperSubType.
       Note that a profile entry to which efmCuPmeOperProfile is
       pointing can be created automatically to reflect achieved
       parameters in adaptive (not fixed) initialization,
       i.e., values of efmCuPmeOperProfile and efmCuAdminProfile or
       efmCuPmeAdminProfile may differ.
       The value of zero indicates that the PME is Down or
       Initializing.
 
       This object partially maps to the aOperatingProfile attribute
       in Clause 30."
     REFERENCE
       "[802.3ah] 30.11.2.1.7"
     ::= { efmCuPmeStatusEntry 4 }
 
 
 
 
   efmCuPmeSnrMgn OBJECT-TYPE
     SYNTAX      Integer32(-127..128|65535)
     UNITS       "dB"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The current Signal to Noise Ratio (SNR) margin with respect
       to the received signal as perceived by the local PME.
       The value of 65535 is returned when the PME is Down or
       Initializing.
 
       This object maps to the aPMESNRMgn attribute in Clause 30.
 
       If a Clause 45 MDIO Interface is present, then this
       object maps to the 10P/2B RX SNR margin register."
     REFERENCE
       "[802.3ah] 30.11.2.1.4, 45.2.1.16"
     ::= { efmCuPmeStatusEntry 5 }
 
   efmCuPmePeerSnrMgn OBJECT-TYPE
     SYNTAX      Integer32(-127..128|65535)
     UNITS       "dB"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The current SNR margin in dB with respect to the received
       signal, as perceived by the remote (link partner) PME.
       The value of 65535 is returned when the PME is Down or
       Initializing.
 
       This object is irrelevant for the -R PME subtypes.  The value
       of 65535 SHALL be returned in this case.
 
       If a Clause 45 MDIO Interface is present, then this
       object maps to the 10P/2B link partner RX SNR margin
       register."
     REFERENCE
       "[802.3ah] 45.2.1.17"
     ::= { efmCuPmeStatusEntry 6}
 
   efmCuPmeLineAtn OBJECT-TYPE
     SYNTAX      Integer32(-127..128|65535)
     UNITS       "dB"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The current Line Attenuation in dB as perceived by the local
       PME.
 
 
 
       The value of 65535 is returned when the PME is Down or
       Initializing.
 
       If a Clause 45 MDIO Interface is present, then this
       object maps to the Line Attenuation register."
     REFERENCE
       "[802.3ah] 45.2.1.18"
     ::= { efmCuPmeStatusEntry 7 }
 
   efmCuPmePeerLineAtn OBJECT-TYPE
     SYNTAX      Integer32(-127..128|65535)
     UNITS       "dB"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The current Line Attenuation in dB as perceived by the remote
       (link partner) PME.
       The value of 65535 is returned when the PME is Down or
       Initializing.
 
       This object is irrelevant for the -R PME subtypes.  The value
       of 65535 SHALL be returned in this case.
 
       If a Clause 45 MDIO Interface is present, then this
       object maps to the 20P/2B link partner Line Attenuation
       register."
     REFERENCE
       "[802.3ah] 45.2.1.19"
     ::= { efmCuPmeStatusEntry 8 }
 
   efmCuPmeEquivalentLength  OBJECT-TYPE
     SYNTAX      Unsigned32(0..8192|65535)
     UNITS       "m"
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "An estimate of the equivalent loop's physical length in
       meters, as perceived by the PME after the link is established.
       An equivalent loop is a hypothetical 26AWG (0.4mm) loop with a
       perfect square root attenuation characteristic, without any
       bridged taps.
       The value of 65535 is returned if the link is Down or
       Initializing or the PME is unable to estimate the equivalent
       length.
 
       For a 10BASE-TL PME, if a Clause 45 MDIO Interface to the PME
       is present, then this object maps to the 10P Electrical Length
       register."
 
 
 
     REFERENCE
       "[802.3ah] 45.2.1.21"
     ::= { efmCuPmeStatusEntry 9 }
 
   efmCuPmeTCCodingErrors OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of 64/65-octet encapsulation errors.  This counter
       is incremented for each 64/65-octet encapsulation error
       detected by the 64/65-octet receive function.
 
       This object maps to aTCCodingViolations attribute in
       Clause 30.
 
       If a Clause 45 MDIO Interface to the PME TC is present, then
       this object maps to the TC coding violations register
       (see 45.2.6.12).
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB."
     REFERENCE
       "[802.3ah] 61.3.3.1, 30.11.2.1.5, 45.2.6.12"
     ::= { efmCuPmeStatusEntry 10 }
 
   efmCuPmeTCCrcErrors OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of TC-CRC errors.  This counter is incremented for
       each TC-CRC error detected by the 64/65-octet receive function
       (see 61.3.3.3 and Figure 61-19).
 
       This object maps to aTCCRCErrors attribute in
       Clause 30.
 
       If a Clause 45 MDIO Interface to the PME TC is present, then
       this object maps to the TC CRC error register
       (see 45.2.6.11).
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB."
 
 
 
     REFERENCE
       "[802.3ah] 61.3.3.3, 30.11.2.1.10, 45.2.6.11"
     ::= { efmCuPmeStatusEntry 11 }
 
  -- 2BASE-TL specific PME group
 
   efmCuPme2B      OBJECT IDENTIFIER ::= { efmCuPme 5 }
 
   efmCuPme2BProfileTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF EfmCuPme2BProfileEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table supports definitions of administrative and
       operating profiles for 2BASE-TL PMEs.
       The first 14 entries in this table SHALL always be defined as
       follows (see 802.3ah Annex 63A):
       -------+-------+-------+-----+------+-------------+-----------
       Profile MinRate MaxRate Power Region Constellation Comment
        index  (Kbps)  (Kbps)  (dBm)
       -------+-------+-------+-----+------+-------------+-----------
          1     5696    5696    13.5    1   32-TCPAM      default
          2     3072    3072    13.5    1   32-TCPAM
          3     2048    2048    13.5    1   16-TCPAM
          4     1024    1024    13.5    1   16-TCPAM
          5      704     704    13.5    1   16-TCPAM
          6      512     512    13.5    1   16-TCPAM
          7     5696    5696    14.5    2   32-TCPAM
          8     3072    3072    14.5    2   32-TCPAM
          9     2048    2048    14.5    2   16-TCPAM
         10     1024    1024    13.5    2   16-TCPAM
         11      704     704    13.5    2   16-TCPAM
         12      512     512    13.5    2   16-TCPAM
         13      192    5696       0    1   0             best effort
         14      192    5696       0    2   0             best effort
       -------+-------+-------+-----+------+-------------+-----------
 
       These default entries SHALL be created during agent
       initialization and MUST NOT be deleted.
 
       Entries following the first 14 can be dynamically created and
       deleted to provide custom administrative (configuration)
       profiles and automatic operating profiles.
 
       This table MUST be maintained in a persistent manner."
     REFERENCE
       "[802.3ah] Annex 63A, 30.11.2.1.6"
     ::= { efmCuPme2B  2 }
 
 
 
   efmCuPme2BProfileEntry OBJECT-TYPE
     SYNTAX      EfmCuPme2BProfileEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Each entry corresponds to a single 2BASE-TL PME profile.
       Each profile contains a set of parameters, used either for
       configuration or representation of a 2BASE-TL PME.
       In case a particular profile is referenced via the
       efmCuPmeAdminProfile object (or efmCuAdminProfile if
       efmCuPmeAdminProfile is zero), it represents the desired
       parameters for the 2BaseTL-O PME initialization.
       If a profile is referenced via an efmCuPmeOperProfile object,
       it represents the current operating parameters of an
       operational PME.
 
       Profiles may be created/deleted using the row creation/
       deletion mechanism via efmCuPme2BProfileRowStatus.  If an
       active entry is referenced, the entry MUST remain 'active'
       until all references are removed.
       Default entries MUST NOT be removed."
     INDEX { efmCuPme2BProfileIndex }
     ::= { efmCuPme2BProfileTable 1 }
 
   EfmCuPme2BProfileEntry ::=
     SEQUENCE {
       efmCuPme2BProfileIndex           EfmProfileIndex,
       efmCuPme2BProfileDescr           SnmpAdminString,
       efmCuPme2BRegion                 INTEGER,
       efmCuPme2BsMode                  EfmProfileIndexOrZero,
       efmCuPme2BMinDataRate            Unsigned32,
       efmCuPme2BMaxDataRate            Unsigned32,
       efmCuPme2BPower                  Unsigned32,
       efmCuPme2BConstellation          INTEGER,
       efmCuPme2BProfileRowStatus       RowStatus
     }
 
   efmCuPme2BProfileIndex OBJECT-TYPE
     SYNTAX      EfmProfileIndex
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "2BASE-TL PME profile index.
       This object is the unique index associated with this profile.
       Entries in this table are referenced via efmCuAdminProfile or
       efmCuPmeAdminProfile objects."
     ::= { efmCuPme2BProfileEntry 1 }
 
 
 
 
   efmCuPme2BProfileDescr OBJECT-TYPE
     SYNTAX      SnmpAdminString
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "A textual string containing information about a 2BASE-TL PME
       profile.  The string may include information about the data
       rate and spectral limitations of this particular profile."
     ::= { efmCuPme2BProfileEntry 2 }
 
   efmCuPme2BRegion  OBJECT-TYPE
     SYNTAX      INTEGER {
       region1(1),
       region2(2)
     }
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "Regional settings for a 2BASE-TL PME, as specified in the
       relevant Regional Annex of [G.991.2].
       Regional settings specify the Power Spectral Density (PSD)
       mask and the Power Back-Off (PBO) values, and place
       limitations on the max allowed data rate, power, and
       constellation.
 
       Possible values for this object are:
         region1      - Annexes A and F (e.g., North America)
         region2      - Annexes B and G (e.g., Europe)
 
       Annex A/B specify regional settings for data rates 192-2304
       Kbps using 16-TCPAM encoding.
       Annex F/G specify regional settings for rates 2320-3840 Kbps
       using 16-TCPAM encoding and 768-5696 Kbps using 32-TCPAM
       encoding.
 
       If a Clause 45 MDIO Interface to the PME is present, then this
       object partially maps to the Region bits in the 2B general
       parameter register."
     REFERENCE
       "[802.3ah] 45.2.1.42; [G.991.2] Annexes A, B, F and G"
     ::= { efmCuPme2BProfileEntry 3 }
 
   efmCuPme2BsMode  OBJECT-TYPE
     SYNTAX      EfmProfileIndexOrZero
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "Desired custom Spectral Mode for a 2BASE-TL PME.  This object
 
 
 
       is a pointer to an entry in efmCuPme2BsModeTable and a block
       of entries in efmCuPme2BRateReachTable, which together define
       (country-specific) reach-dependent rate limitations in
       addition to those defined by efmCuPme2BRegion.
 
       The value of this object is the index of the referenced
       spectral mode.
       The value of zero (default) indicates that no specific
       spectral mode is applicable.
 
       Attempts to set this object to a value that is not the value
       of the index for an active entry in the corresponding spectral
       mode table MUST be rejected."
     REFERENCE
       "efmCuPme2BsModeTable, efmCuPme2BRateReachTable"
     DEFVAL { 0 }
     ::= { efmCuPme2BProfileEntry 4 }
 
   efmCuPme2BMinDataRate  OBJECT-TYPE
     SYNTAX  Unsigned32(192..5696)
     UNITS       "Kbps"
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "Minimum Data Rate for the 2BASE-TL PME.
       This object can take values of (n x 64)Kbps,
       where n=3..60 for 16-TCPAM and n=12..89 for 32-TCPAM encoding.
 
       The data rate of the 2BASE-TL PME is considered 'fixed' when
       the value of this object equals that of efmCuPme2BMaxDataRate.
       If efmCuPme2BMinDataRate is less than efmCuPme2BMaxDataRate in
       the administrative profile, the data rate is considered
       'adaptive', and SHALL be set to the maximum attainable rate
       not exceeding efmCuPme2BMaxDataRate, under the spectral
       limitations placed by the efmCuPme2BRegion and
       efmCuPme2BsMode.
 
       Note that the current operational data rate of the PME is
       represented by the ifSpeed object of IF-MIB.
 
       If a Clause 45 MDIO Interface to the PME is present, then this
       object maps to the Min Data Rate1 bits in the 2B PMD
       parameters register.
 
       This object MUST be maintained in a persistent manner."
     REFERENCE
       "[802.3ah] 45.2.1.43"
     ::= { efmCuPme2BProfileEntry 5 }
 
 
 
   efmCuPme2BMaxDataRate  OBJECT-TYPE
     SYNTAX  Unsigned32(192..5696)
     UNITS       "Kbps"
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "Maximum Data Rate for the 2BASE-TL PME.
       This object can take values of (n x 64)Kbps,
       where n=3..60 for 16-TCPAM and n=12..89 for 32-TCPAM encoding.
 
       The data rate of the 2BASE-TL PME is considered 'fixed' when
       the value of this object equals that of efmCuPme2BMinDataRate.
       If efmCuPme2BMinDataRate is less than efmCuPme2BMaxDataRate in
       the administrative profile, the data rate is considered
       'adaptive', and SHALL be set to the maximum attainable rate
       not exceeding efmCuPme2BMaxDataRate, under the spectral
       limitations placed by the efmCuPme2BRegion and
       efmCuPme2BsMode.
 
       Note that the current operational data rate of the PME is
       represented by the ifSpeed object of IF-MIB.
 
       If a Clause 45 MDIO Interface to the PME is present, then this
       object maps to the Max Data Rate1 bits in the 2B PMD
       parameters register.
 
       This object MUST be maintained in a persistent manner."
     REFERENCE
       "[802.3ah] 45.2.1.43"
     ::= { efmCuPme2BProfileEntry 6 }
 
   efmCuPme2BPower  OBJECT-TYPE
     SYNTAX      Unsigned32(0|10..42)
     UNITS       "0.5 dBm"
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "Signal Transmit Power.  Multiple of 0.5 dBm.
       The value of 0 in the administrative profile means that the
       signal transmit power is not fixed and SHALL be set to
       maximize the attainable rate, under the spectral limitations
       placed by the efmCuPme2BRegion and efmCuPme2BsMode.
 
       If a Clause 45 MDIO Interface to the PME is present, then this
       object maps to the Power1 bits in the 2B PMD parameters
       register."
     REFERENCE
       "[802.3ah] 45.2.1.43"
 
 
 
     ::= { efmCuPme2BProfileEntry 7 }
 
   efmCuPme2BConstellation  OBJECT-TYPE
     SYNTAX      INTEGER {
       adaptive(0),
       tcpam16(1),
       tcpam32(2)
     }
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "TCPAM Constellation of the 2BASE-TL PME.
       The possible values are:
         adaptive(0)    - either 16- or 32-TCPAM
         tcpam16(1)     - 16-TCPAM
         tcpam32(2)     - 32-TCPAM
 
       The value of adaptive(0) in the administrative profile means
       that the constellation is not fixed and SHALL be set to
       maximize the attainable rate, under the spectral limitations
       placed by the efmCuPme2BRegion and efmCuPme2BsMode.
 
       If a Clause 45 MDIO Interface to the PME is present, then this
       object maps to the Constellation1 bits in the 2B general
       parameter register."
     REFERENCE
        "[802.3ah] 45.2.1.43"
     ::= { efmCuPme2BProfileEntry 8 }
 
   efmCuPme2BProfileRowStatus OBJECT-TYPE
     SYNTAX      RowStatus
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "This object controls the creation, modification, or deletion
       of the associated entry in the efmCuPme2BProfileTable per the
       semantics of RowStatus.
 
       If an 'active' entry is referenced via efmCuAdminProfile or
       efmCuPmeAdminProfile instance(s), the entry MUST remain
       'active'.
 
       An 'active' entry SHALL NOT be modified.  In order to modify
       an existing entry, it MUST be taken out of service (by setting
       this object to 'notInService'), modified, and set 'active'
       again."
     ::= { efmCuPme2BProfileEntry 9 }
 
 
 
 
   efmCuPme2BsModeTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF EfmCuPme2BsModeEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table, together with efmCu2BReachRateTable, supports
       definition of administrative custom spectral modes for
       2BASE-TL PMEs, describing spectral limitations in addition to
       those specified by efmCuPme2BRegion.
 
       In some countries, spectral regulations (e.g., UK ANFP) limit
       the length of the loops for certain data rates.  This table
       allows these country-specific limitations to be specified.
 
       Entries in this table referenced by the efmCuPme2BsMode
       MUST NOT be deleted until all the active references are
       removed.
 
       This table MUST be maintained in a persistent manner."
     REFERENCE
       "efmCu2BReachRateTable"
     ::= { efmCuPme2B  3 }
 
   efmCuPme2BsModeEntry OBJECT-TYPE
     SYNTAX      EfmCuPme2BsModeEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Each entry specifies a spectral mode description and its
       index, which is used to reference corresponding entries in the
       efmCu2BReachRateTable.
 
       Entries may be created/deleted using the row creation/
       deletion mechanism via efmCuPme2BsModeRowStatus."
     INDEX { efmCuPme2BsModeIndex }
     ::= { efmCuPme2BsModeTable 1 }
 
   EfmCuPme2BsModeEntry ::=
     SEQUENCE {
       efmCuPme2BsModeIndex             EfmProfileIndex,
       efmCuPme2BsModeDescr             SnmpAdminString,
       efmCuPme2BsModeRowStatus         RowStatus
     }
 
   efmCuPme2BsModeIndex OBJECT-TYPE
     SYNTAX      EfmProfileIndex
     MAX-ACCESS  not-accessible
     STATUS      current
 
 
 
     DESCRIPTION
       "2BASE-TL PME Spectral Mode index.
       This object is the unique index associated with this spectral
       mode.
       Entries in this table are referenced via the efmCuPme2BsMode
       object."
     ::= { efmCuPme2BsModeEntry 1 }
 
   efmCuPme2BsModeDescr OBJECT-TYPE
     SYNTAX      SnmpAdminString
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "A textual string containing information about a 2BASE-TL PME
       spectral mode.  The string may include information about
       corresponding (country-specific) spectral regulations
       and rate/reach limitations of this particular spectral mode."
     ::= { efmCuPme2BsModeEntry 2 }
 
   efmCuPme2BsModeRowStatus OBJECT-TYPE
     SYNTAX      RowStatus
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "This object controls creation, modification, or deletion of
       the associated entry in efmCuPme2BsModeTable per the semantics
       of RowStatus.
 
       If an 'active' entry is referenced via efmCuPme2BsMode
       instance(s), the entry MUST remain 'active'.
 
       An 'active' entry SHALL NOT be modified.  In order to modify
       an existing entry, it MUST be taken out of service (by setting
       this object to 'notInService'), modified, and set 'active'
       again."
     ::= { efmCuPme2BsModeEntry 3 }
 
 
   efmCuPme2BReachRateTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF EfmCuPme2BReachRateEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table supports the definition of administrative custom
       spectral modes for 2BASE-TL PMEs, providing spectral
       limitations in addition to those specified by
       efmCuPme2BRegion.
 
 
 
 
       The spectral regulations in some countries (e.g., UK ANFP)
       limit the length of the loops for certain data rates.
       This table allows these country-specific limitations to be
       specified.
 
       Below is an example of this table for [ANFP]:
       ----------+-------+-------
       Equivalent MaxRate MaxRate
         Length    PAM16   PAM32
           (m)     (Kbps)  (Kbps)
       ----------+-------+-------
           975      2304    5696
          1125      2304    5504
          1275      2304    5120
          1350      2304    4864
          1425      2304    4544
          1500      2304    4288
          1575      2304    3968
          1650      2304    3776
          1725      2304    3520
          1800      2304    3264
          1875      2304    3072
          1950      2048    2688
          2100      1792    2368
          2250      1536       0
          2400      1408       0
          2550      1280       0
          2775      1152       0
          2925      1152       0
          3150      1088       0
          3375      1024       0
       ----------+-------+-------
 
       Entries in this table referenced by an efmCuPme2BsMode
       instance MUST NOT be deleted.
 
       This table MUST be maintained in a persistent manner."
     REFERENCE
       "[ANFP]"
     ::= { efmCuPme2B  4 }
 
   efmCuPme2BReachRateEntry OBJECT-TYPE
     SYNTAX      EfmCuPme2BReachRateEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Each entry specifies maximum 2BASE-TL PME data rates
       allowed for a certain equivalent loop length, when using
 
 
 
       16-TCPAM or 32-TCPAM encoding.
 
       When a 2BASE-TL PME is initialized, its data rate MUST NOT
       exceed one of the following limitations:
       - the value of efmCuPme2BMaxDataRate
       - maximum data rate allowed by efmCuPme2BRegion and
         efmCuPme2BPower
       - maximum data rate for a given encoding specified in the
         efmCuPme2BsModeEntry, corresponding to the equivalent loop
         length, estimated by the PME
 
       It is RECOMMENDED that the efmCuPme2BEquivalentLength values
       are assigned in increasing order, starting from the minimum
       value.
 
       Entries may be created/deleted using the row creation/
       deletion mechanism via efmCuPme2ReachRateRowStatus."
     INDEX { efmCuPme2BsModeIndex, efmCuPme2BReachRateIndex }
     ::= { efmCuPme2BReachRateTable 1 }
 
   EfmCuPme2BReachRateEntry ::=
     SEQUENCE {
       efmCuPme2BReachRateIndex         EfmProfileIndex,
       efmCuPme2BEquivalentLength       Unsigned32,
       efmCuPme2BMaxDataRatePam16       Unsigned32,
       efmCuPme2BMaxDataRatePam32       Unsigned32,
       efmCuPme2BReachRateRowStatus     RowStatus
     }
 
   efmCuPme2BReachRateIndex OBJECT-TYPE
     SYNTAX      EfmProfileIndex
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "2BASE-TL custom spectral mode Reach-Rate table index.
       This object is the unique index associated with each entry."
     ::= { efmCuPme2BReachRateEntry 1 }
 
   efmCuPme2BEquivalentLength  OBJECT-TYPE
     SYNTAX      Unsigned32(0..8192)
     UNITS       "m"
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "Maximum allowed equivalent loop's physical length in meters
       for the specified data rates.
       An equivalent loop is a hypothetical 26AWG (0.4mm) loop with a
       perfect square root attenuation characteristic, without any
 
 
 
       bridged taps."
     ::= { efmCuPme2BReachRateEntry 2 }
 
   efmCuPme2BMaxDataRatePam16  OBJECT-TYPE
     SYNTAX      Unsigned32(0|192..5696)
     UNITS       "Kbps"
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "Maximum data rate for a 2BASE-TL PME at the specified
       equivalent loop's length using TC-PAM16 encoding.
       The value of zero means that TC-PAM16 encoding should not be
       used at this distance."
     ::= { efmCuPme2BReachRateEntry 3 }
 
   efmCuPme2BMaxDataRatePam32  OBJECT-TYPE
     SYNTAX      Unsigned32(0|192..5696)
     UNITS       "Kbps"
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "Maximum data rate for a 2BASE-TL PME at the specified
       equivalent loop's length using TC-PAM32 encoding.
       The value of zero means that TC-PAM32 encoding should not be
       used at this distance."
     ::= { efmCuPme2BReachRateEntry 4 }
 
   efmCuPme2BReachRateRowStatus OBJECT-TYPE
     SYNTAX      RowStatus
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "This object controls the creation, modification, or deletion
       of the associated entry in the efmCuPme2BReachRateTable per
       the semantics of RowStatus.
 
       If an 'active' entry is referenced via efmCuPme2BsMode
       instance(s), the entry MUST remain 'active'.
 
       An 'active' entry SHALL NOT be modified.  In order to modify
       an existing entry, it MUST be taken out of service (by setting
       this object to 'notInService'), modified, and set 'active'
       again."
     ::= { efmCuPme2BReachRateEntry 5 }
 
 
  -- 10PASS-TS specific PME group
 
 
 
 
   efmCuPme10P      OBJECT IDENTIFIER ::= { efmCuPme 6 }
 
   efmCuPme10PProfileTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF EfmCuPme10PProfileEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table supports definitions of configuration profiles for
       10PASS-TS PMEs.
       The first 22 entries in this table SHALL always be defined as
       follows (see 802.3ah Annex 62B.3, table 62B-1):
       -------+--------+----+---------+-----+-----+---------------
       Profile Bandplan UPBO BandNotch DRate URate Comment
        Index  PSDMask#  p#    p#        p#    p#
       -------+--------+----+---------+-----+-----+---------------
          1      1      3    2,6,10,11    20    20 default profile
          2     13      5    0            20    20
          3      1      1    0            20    20
          4     16      0    0           100   100
          5     16      0    0            70    50
          6      6      0    0            50    10
          7     17      0    0            30    30
          8      8      0    0            30     5
          9      4      0    0            25    25
         10      4      0    0            15    15
         11     23      0    0            10    10
         12     23      0    0             5     5
         13     16      0    2,5,9,11    100   100
         14     16      0    2,5,9,11     70    50
         15      6      0    2,6,10,11    50    10
         16     17      0    2,5,9,11     30    30
         17      8      0    2,6,10,11    30     5
         18      4      0    2,6,10,11    25    25
         19      4      0    2,6,10,11    15    15
         20     23      0    2,5,9,11     10    10
         21     23      0    2,5,9,11      5     5
         22     30      0    0           200    50
       -------+--------+----+---------+-----+-----+---------------
 
       These default entries SHALL be created during agent
       initialization and MUST NOT be deleted.
 
       Entries following the first 22 can be dynamically created and
       deleted to provide custom administrative (configuration)
       profiles and automatic operating profiles.
 
       This table MUST be maintained in a persistent manner."
     REFERENCE
 
 
 
       "[802.3ah] Annex 62B.3, 30.11.2.1.6"
     ::= { efmCuPme10P  1 }
 
   efmCuPme10PProfileEntry OBJECT-TYPE
     SYNTAX      EfmCuPme10PProfileEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "Each entry corresponds to a single 10PASS-TS PME profile.
 
       Each profile contains a set of parameters, used either for
       configuration or representation of a 10PASS-TS PME.
       In case a particular profile is referenced via the
       efmCuPmeAdminProfile object (or efmCuAdminProfile if
       efmCuPmeAdminProfile is zero), it represents the desired
       parameters for the 10PassTS-O PME initialization.
       If a profile is referenced via an efmCuPmeOperProfile object,
       it represents the current operating parameters of the PME.
 
       Profiles may be created/deleted using the row creation/
       deletion mechanism via efmCuPme10PProfileRowStatus.  If an
       'active' entry is referenced, the entry MUST remain 'active'
       until all references are removed.
       Default entries MUST NOT be removed."
     INDEX { efmCuPme10PProfileIndex }
     ::= { efmCuPme10PProfileTable 1 }
 
   EfmCuPme10PProfileEntry ::=
     SEQUENCE {
       efmCuPme10PProfileIndex           EfmProfileIndex,
       efmCuPme10PProfileDescr           SnmpAdminString,
       efmCuPme10PBandplanPSDMskProfile  INTEGER,
       efmCuPme10PUPBOReferenceProfile   INTEGER,
       efmCuPme10PBandNotchProfiles      BITS,
       efmCuPme10PPayloadDRateProfile    INTEGER,
       efmCuPme10PPayloadURateProfile    INTEGER,
       efmCuPme10PProfileRowStatus       RowStatus
     }
 
   efmCuPme10PProfileIndex OBJECT-TYPE
     SYNTAX      EfmProfileIndex
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "10PASS-TS PME profile index.
       This object is the unique index associated with this profile.
       Entries in this table are referenced via efmCuAdminProfile or
       efmCuPmeAdminProfile."
 
 
 
     ::= { efmCuPme10PProfileEntry 1 }
 
   efmCuPme10PProfileDescr OBJECT-TYPE
     SYNTAX      SnmpAdminString
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "A textual string containing information about a 10PASS-TS PME
       profile.  The string may include information about data rate
       and spectral limitations of this particular profile."
     ::= { efmCuPme10PProfileEntry 2 }
 
   efmCuPme10PBandplanPSDMskProfile  OBJECT-TYPE
     SYNTAX  INTEGER {
       profile1(1),
       profile2(2),
       profile3(3),
       profile4(4),
       profile5(5),
       profile6(6),
       profile7(7),
       profile8(8),
       profile9(9),
       profile10(10),
       profile11(11),
       profile12(12),
       profile13(13),
       profile14(14),
       profile15(15),
       profile16(16),
       profile17(17),
       profile18(18),
       profile19(19),
       profile20(20),
       profile21(21),
       profile22(22),
       profile23(23),
       profile24(24),
       profile25(25),
       profile26(26),
       profile27(27),
       profile28(28),
       profile29(29),
       profile30(30)
     }
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
 
 
 
       "The 10PASS-TS PME Bandplan and PSD Mask Profile, as specified
       in 802.3ah Annex 62A, table 62A-1.  Possible values are:
       --------------+------------------------+------------+--------
       Profile Name    PSD Mask                  Bands      G.993.1
                                               0/1/2/3/4/5  Bandplan
       --------------+------------------------+------------+--------
       profile1(1)    T1.424 FTTCab.M1         x/D/U/D/U    A
       profile2(2)    T1.424 FTTEx.M1          x/D/U/D/U    A
       profile3(3)    T1.424 FTTCab.M2         x/D/U/D/U    A
       profile4(4)    T1.424 FTTEx.M2          x/D/U/D/U    A
       profile5(5)    T1.424 FTTCab.M1         D/D/U/D/U    A
       profile6(6)    T1.424 FTTEx.M1          D/D/U/D/U    A
       profile7(7)    T1.424 FTTCab.M2         D/D/U/D/U    A
       profile8(8)    T1.424 FTTEx.M2          D/D/U/D/U    A
       profile9(9)    T1.424 FTTCab.M1         U/D/U/D/x    A
       profile10(10)  T1.424 FTTEx.M1          U/D/U/D/x    A
       profile11(11)  T1.424 FTTCab.M2         U/D/U/D/x    A
       profile12(12)  T1.424 FTTEx.M2          U/D/U/D/x    A
       profile13(13)  TS 101 270-1 Pcab.M1.A   x/D/U/D/U    B
       profile14(14)  TS 101 270-1 Pcab.M1.B   x/D/U/D/U    B
       profile15(15)  TS 101 270-1 Pex.P1.M1   x/D/U/D/U    B
       profile16(16)  TS 101 270-1 Pex.P2.M1   x/D/U/D/U    B
       profile17(17)  TS 101 270-1 Pcab.M2     x/D/U/D/U    B
       profile18(18)  TS 101 270-1 Pex.P1.M2   x/D/U/D/U    B
       profile19(19)  TS 101 270-1 Pex.P2.M2   x/D/U/D/U    B
       profile20(20)  TS 101 270-1 Pcab.M1.A   U/D/U/D/x    B
       profile21(21)  TS 101 270-1 Pcab.M1.B   U/D/U/D/x    B
       profile22(22)  TS 101 270-1 Pex.P1.M1   U/D/U/D/x    B
       profile23(23)  TS 101 270-1 Pex.P2.M1   U/D/U/D/x    B
       profile24(24)  TS 101 270-1 Pcab.M2     U/D/U/D/x    B
       profile25(25)  TS 101 270-1 Pex.P1.M2   U/D/U/D/x    B
       profile26(26)  TS 101 270-1 Pex.P2.M2   U/D/U/D/x    B
       profile27(27)  G.993.1 F.1.2.1          x/D/U/D/U    Annex F
       profile28(28)  G.993.1 F.1.2.2          x/D/U/D/U    Annex F
       profile29(29)  G.993.1 F.1.2.3          x/D/U/D/U    Annex F
       profile30(30)  T1.424 FTTCab.M1 (ext.)  x/D/U/D/U/D  Annex A
       --------------+------------------------+------------+--------
       "
     REFERENCE
       "[802.3ah] Annex 62A"
     ::= { efmCuPme10PProfileEntry 3 }
 
   efmCuPme10PUPBOReferenceProfile  OBJECT-TYPE
     SYNTAX  INTEGER {
       profile0(0),
       profile1(1),
       profile2(2),
       profile3(3),
 
 
 
       profile4(4),
       profile5(5),
       profile6(6),
       profile7(7),
       profile8(8),
       profile9(9)
     }
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "The 10PASS-TS PME Upstream Power Back-Off (UPBO) Reference
       PSD Profile, as specified in 802.3 Annex 62A, table 62A-3.
       Possible values are:
       ------------+-----------------------------
       Profile Name   Reference PSD
       ------------+-----------------------------
       profile0(0)  no profile
       profile1(1)  T1.424        Noise A    M1
       profile2(2)  T1.424        Noise A    M2
       profile3(3)  T1.424        Noise F    M1
       profile4(4)  T1.424        Noise F    M2
       profile5(5)  TS 101 270-1  Noise A&B
       profile6(6)  TS 101 270-1  Noise C
       profile7(7)  TS 101 270-1  Noise D
       profile8(8)  TS 101 270-1  Noise E
       profile9(9)  TS 101 270-1  Noise F
       ------------+-----------------------------
       "
     REFERENCE
       "[802.3ah] Annex 62A.3.5"
     ::= { efmCuPme10PProfileEntry 4 }
 
   efmCuPme10PBandNotchProfiles  OBJECT-TYPE
     SYNTAX  BITS {
       profile0(0),
       profile1(1),
       profile2(2),
       profile3(3),
       profile4(4),
       profile5(5),
       profile6(6),
       profile7(7),
       profile8(8),
       profile9(9),
       profile10(10),
       profile11(11)
     }
     MAX-ACCESS  read-create
 
 
 
     STATUS      current
     DESCRIPTION
       "The 10PASS-TS PME Egress Control Band Notch Profile bitmap,
       as specified in 802.3 Annex 62A, table 62A-4.  Possible values
       are:
       --------------+--------+------+------------+------+------
       Profile Name   G.991.3  T1.424 TS 101 270-1 StartF EndF
                      table    table  table        (MHz)  (MHz)
       --------------+--------+------+------------+------+------
       profile0(0)    no profile
       profile1(1)    F-5 #01  -      -            1.810  1.825
       profile2(2)    6-2      15-1   17           1.810  2.000
       profile3(3)    F-5 #02  -      -            1.907  1.912
       profile4(4)    F-5 #03  -      -            3.500  3.575
       profile5(5)    6-2      -      17           3.500  3.800
       profile6(6)    -        15-1   -            3.500  4.000
       profile7(7)    F-5 #04  -      -            3.747  3.754
       profile8(8)    F-5 #05  -      -            3.791  3.805
       profile9(9)    6-2      -      17           7.000  7.100
       profile10(10)  F-5 #06  15-1   -            7.000  7.300
       profile11(11)  6-2      15-1   1            10.100 10.150
       --------------+--------+------+------------+------+------
 
       Any combination of profiles can be specified by ORing
       individual profiles, for example, a value of 0x2230 selects
       profiles 2, 6, 10, and 11."
     REFERENCE
       "[802.3ah] Annex 62A.3.5"
     ::= { efmCuPme10PProfileEntry 5 }
 
   efmCuPme10PPayloadDRateProfile  OBJECT-TYPE
     SYNTAX      INTEGER {
       profile5(5),
       profile10(10),
       profile15(15),
       profile20(20),
       profile25(25),
       profile30(30),
       profile50(50),
       profile70(70),
       profile100(100),
       profile140(140),
       profile200(200)
     }
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "The 10PASS-TS PME Downstream Payload Rate Profile, as
 
 
 
       specified in 802.3 Annex 62A.  Possible values are:
         profile5(5)      - 2.5 Mbps
         profile10(10)    - 5 Mbps
         profile15(15)    - 7.5 Mbps
         profile20(20)    - 10 Mbps
         profile25(25)    - 12.5 Mbps
         profile30(30)    - 15 Mbps
         profile50(50)    - 25 Mbps
         profile70(70)    - 35 Mbps
         profile100(100)  - 50 Mbps
         profile140(140)  - 70 Mbps
         profile200(200)  - 100 Mbps
 
       Each value represents a target for the PME's Downstream
       Payload Bitrate as seen at the MII.  If the payload rate of
       the selected profile cannot be achieved based on the loop
       environment, bandplan, and PSD mask, the PME initialization
       SHALL fail."
     REFERENCE
       "[802.3ah] Annex 62A.3.6"
     ::= { efmCuPme10PProfileEntry 6 }
 
   efmCuPme10PPayloadURateProfile  OBJECT-TYPE
     SYNTAX      INTEGER {
       profile5(5),
       profile10(10),
       profile15(15),
       profile20(20),
       profile25(25),
       profile30(30),
       profile50(50),
       profile70(70),
       profile100(100)
     }
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "The 10PASS-TS PME Upstream Payload Rate Profile, as specified
        in 802.3 Annex 62A.  Possible values are:
         profile5(5)       - 2.5 Mbps
         profile10(10)     - 5 Mbps
         profile15(15)     - 7.5 Mbps
         profile20(20)     - 10 Mbps
         profile25(25)     - 12.5 Mbps
         profile30(30)     - 15 Mbps
         profile50(50)     - 25 Mbps
         profile70(70)     - 35 Mbps
         profile100(100)   - 50 Mbps
 
 
 
       Each value represents a target for the PME's Upstream Payload
       Bitrate as seen at the MII.  If the payload rate of the
       selected profile cannot be achieved based on the loop
       environment, bandplan, and PSD mask, the PME initialization
       SHALL fail."
     REFERENCE
       "[802.3ah] Annex 62A.3.6"
     ::= { efmCuPme10PProfileEntry 7 }
 
   efmCuPme10PProfileRowStatus OBJECT-TYPE
     SYNTAX      RowStatus
     MAX-ACCESS  read-create
     STATUS      current
     DESCRIPTION
       "This object controls creation, modification, or deletion of
       the associated entry in efmCuPme10PProfileTable per the
       semantics of RowStatus.
 
       If an active entry is referenced via efmCuAdminProfile or
       efmCuPmeAdminProfile, the entry MUST remain 'active' until
       all references are removed.
 
       An 'active' entry SHALL NOT be modified.  In order to modify
       an existing entry, it MUST be taken out of service (by setting
       this object to 'notInService'), modified, and set 'active'
       again."
     ::= { efmCuPme10PProfileEntry 8 }
 
 
   efmCuPme10PStatusTable OBJECT-TYPE
     SYNTAX      SEQUENCE OF EfmCuPme10PStatusEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "This table provides status information of EFMCu 10PASS-TS
       PMEs (modems).
 
       This table contains live data from the equipment.  As such,
       it is NOT persistent."
     ::= { efmCuPme10P 2 }
 
   efmCuPme10PStatusEntry OBJECT-TYPE
     SYNTAX      EfmCuPme10PStatusEntry
     MAX-ACCESS  not-accessible
     STATUS      current
     DESCRIPTION
       "An entry in the EFMCu 10PASS-TS PME Status table."
     INDEX  { ifIndex }
 
 
 
     ::= { efmCuPme10PStatusTable 1 }
 
   EfmCuPme10PStatusEntry ::=
     SEQUENCE {
       efmCuPme10PFECCorrectedBlocks     Counter32,
       efmCuPme10PFECUncorrectedBlocks   Counter32
     }
 
   efmCuPme10PFECCorrectedBlocks  OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of received and corrected Forward Error Correction
       (FEC) codewords in this 10PASS-TS PME.
 
       This object maps to the aPMEFECCorrectedBlocks attribute in
       Clause 30.
 
       If a Clause 45 MDIO Interface to the PMA/PMD is present,
       then this object maps to the 10P FEC correctable errors
       register.
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB."
     REFERENCE
       "[802.3ah] 45.2.1.22, 30.11.2.1.8"
     ::= { efmCuPme10PStatusEntry 1 }
 
   efmCuPme10PFECUncorrectedBlocks  OBJECT-TYPE
     SYNTAX      Counter32
     MAX-ACCESS  read-only
     STATUS      current
     DESCRIPTION
       "The number of received uncorrectable FEC codewords in this
       10PASS-TS PME.
 
       This object maps to the aPMEFECUncorrectableBlocks attribute
       in Clause 30.
 
       If a Clause 45 MDIO Interface to the PMA/PMD is present,
       then this object maps to the 10P FEC uncorrectable errors
       register.
 
       Discontinuities in the value of this counter can occur at
       re-initialization of the management system, and at other times
 
 
 
       as indicated by the value of ifCounterDiscontinuityTime,
       defined in IF-MIB."
     REFERENCE
       "[802.3ah] 45.2.1.23, 30.11.2.1.9"
     ::= { efmCuPme10PStatusEntry 2 }
 
  --
  -- Conformance Statements
  --
 
   efmCuGroups      OBJECT IDENTIFIER ::= { efmCuConformance 1 }
 
   efmCuCompliances OBJECT IDENTIFIER ::= { efmCuConformance 2 }
 
   -- Object Groups
 
   efmCuBasicGroup OBJECT-GROUP
     OBJECTS {
       efmCuPAFSupported,
       efmCuAdminProfile,
       efmCuTargetDataRate,
       efmCuTargetSnrMgn,
       efmCuAdaptiveSpectra,
       efmCuPortSide,
       efmCuFltStatus
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects representing management information
       common for all types of EFMCu ports."
     ::= { efmCuGroups 1 }
 
   efmCuPAFGroup OBJECT-GROUP
     OBJECTS {
       efmCuPeerPAFSupported,
       efmCuPAFCapacity,
       efmCuPeerPAFCapacity,
       efmCuPAFAdminState,
       efmCuPAFDiscoveryCode,
       efmCuPAFRemoteDiscoveryCode,
       efmCuNumPMEs
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects supporting OPTIONAL PME
       Aggregation Function (PAF) and PAF discovery in EFMCu ports."
     ::= { efmCuGroups 2 }
 
 
 
 
   efmCuPAFErrorsGroup OBJECT-GROUP
     OBJECTS {
       efmCuPAFInErrors,
       efmCuPAFInSmallFragments,
       efmCuPAFInLargeFragments,
       efmCuPAFInBadFragments,
       efmCuPAFInLostFragments,
       efmCuPAFInLostStarts,
       efmCuPAFInLostEnds,
       efmCuPAFInOverflows
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects supporting OPTIONAL error counters
       of PAF on EFMCu ports."
     ::= { efmCuGroups 3 }
 
   efmCuPmeGroup OBJECT-GROUP
     OBJECTS {
       efmCuPmeAdminProfile,
       efmCuPmeOperStatus,
       efmCuPmeFltStatus,
       efmCuPmeSubTypesSupported,
       efmCuPmeAdminSubType,
       efmCuPmeOperSubType,
       efmCuPAFRemoteDiscoveryCode,
       efmCuPmeOperProfile,
       efmCuPmeSnrMgn,
       efmCuPmePeerSnrMgn,
       efmCuPmeLineAtn,
       efmCuPmePeerLineAtn,
       efmCuPmeEquivalentLength,
       efmCuPmeTCCodingErrors,
       efmCuPmeTCCrcErrors,
       efmCuPmeThreshLineAtn,
       efmCuPmeThreshSnrMgn
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects providing information about
       a 2BASE-TL/10PASS-TS PME."
     ::= { efmCuGroups 4 }
 
   efmCuAlarmConfGroup OBJECT-GROUP
     OBJECTS {
       efmCuThreshLowRate,
       efmCuLowRateCrossingEnable,
       efmCuPmeThreshLineAtn,
 
 
 
       efmCuPmeLineAtnCrossingEnable,
       efmCuPmeThreshSnrMgn,
       efmCuPmeSnrMgnCrossingEnable,
       efmCuPmeDeviceFaultEnable,
       efmCuPmeConfigInitFailEnable,
       efmCuPmeProtocolInitFailEnable
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects supporting configuration of alarm
       thresholds and notifications in EFMCu ports."
     ::= { efmCuGroups 5 }
 
   efmCuNotificationGroup NOTIFICATION-GROUP
     NOTIFICATIONS {
       efmCuLowRateCrossing,
       efmCuPmeLineAtnCrossing,
       efmCuPmeSnrMgnCrossing,
       efmCuPmeDeviceFault,
       efmCuPmeConfigInitFailure,
       efmCuPmeProtocolInitFailure
     }
     STATUS      current
     DESCRIPTION
       "This group supports notifications of significant conditions
       associated with EFMCu ports."
     ::= { efmCuGroups 6 }
 
   efmCuPme2BProfileGroup OBJECT-GROUP
     OBJECTS {
       efmCuPme2BProfileDescr,
       efmCuPme2BRegion,
       efmCuPme2BsMode,
       efmCuPme2BMinDataRate,
       efmCuPme2BMaxDataRate,
       efmCuPme2BPower,
       efmCuPme2BConstellation,
       efmCuPme2BProfileRowStatus,
       efmCuPme2BsModeDescr,
       efmCuPme2BsModeRowStatus,
       efmCuPme2BEquivalentLength,
       efmCuPme2BMaxDataRatePam16,
       efmCuPme2BMaxDataRatePam32,
       efmCuPme2BReachRateRowStatus
     }
     STATUS      current
     DESCRIPTION
       "A collection of objects that constitute a configuration
 
 
 
       profile for configuration of 2BASE-TL ports."
     ::= { efmCuGroups 7}
 
   efmCuPme10PProfileGroup OBJECT-GROUP
     OBJECTS {
       efmCuPme10PProfileDescr,
       efmCuPme10PBandplanPSDMskProfile,
       efmCuPme10PUPBOReferenceProfile,
       efmCuPme10PBandNotchProfiles,
       efmCuPme10PPayloadDRateProfile,
       efmCuPme10PPayloadURateProfile,
       efmCuPme10PProfileRowStatus
     }
     STATUS  current
     DESCRIPTION
       "A collection of objects that constitute a configuration
       profile for configuration of 10PASS-TS ports."
     ::= { efmCuGroups 8 }
 
   efmCuPme10PStatusGroup OBJECT-GROUP
     OBJECTS {
       efmCuPme10PFECCorrectedBlocks,
       efmCuPme10PFECUncorrectedBlocks
     }
     STATUS  current
     DESCRIPTION
       "A collection of objects providing status information
       specific to 10PASS-TS PMEs."
     ::= { efmCuGroups 9 }
 
  -- Compliance Statements
 
   efmCuCompliance MODULE-COMPLIANCE
     STATUS      current
     DESCRIPTION
       "The compliance statement for 2BASE-TL/10PASS-TS interfaces.
       Compliance with the following external compliance statements
       is REQUIRED:
 
       MIB Module             Compliance Statement
       ----------             --------------------
       IF-MIB                 ifCompliance3
       EtherLike-MIB          dot3Compliance2
       MAU-MIB                mauModIfCompl3
 
       Compliance with the following external compliance statements
       is OPTIONAL for implementations supporting PME Aggregation
       Function (PAF) with flexible cross-connect between the PCS
 
 
 
       and PME ports:
 
       MIB Module             Compliance Statement
       ----------             --------------------
       IF-INVERTED-STACK-MIB  ifInvCompliance
       IF-CAP-STACK-MIB       ifCapStackCompliance"
 
     MODULE  -- this module
       MANDATORY-GROUPS {
         efmCuBasicGroup,
         efmCuPmeGroup,
         efmCuAlarmConfGroup,
         efmCuNotificationGroup
       }
 
       GROUP       efmCuPme2BProfileGroup
       DESCRIPTION
         "Support for this group is only required for implementations
         supporting 2BASE-TL PHY."
 
       GROUP       efmCuPme10PProfileGroup
       DESCRIPTION
         "Support for this group is only required for implementations
         supporting 10PASS-TS PHY."
 
       GROUP       efmCuPAFGroup
       DESCRIPTION
         "Support for this group is only required for
         implementations supporting PME Aggregation Function (PAF)."
 
       GROUP       efmCuPAFErrorsGroup
       DESCRIPTION
         "Support for this group is OPTIONAL for implementations
         supporting PME Aggregation Function (PAF)."
 
       GROUP       efmCuPme10PStatusGroup
       DESCRIPTION
         "Support for this group is OPTIONAL for implementations
         supporting 10PASS-TS PHY."
 
       OBJECT      efmCuPmeSubTypesSupported
       SYNTAX      BITS {
         ieee2BaseTLO(0),
         ieee2BaseTLR(1),
         ieee10PassTSO(2),
         ieee10PassTSR(3)
       }
       DESCRIPTION
 
 
 
         "Support for all subtypes is not required.  However, at
         least one value SHALL be supported."
 
       OBJECT      efmCuPmeAdminSubType
       MIN-ACCESS  read-only
       DESCRIPTION
         "Write access is not required (needed only for PMEs
         supporting more than a single subtype, e.g.,
         ieee2BaseTLO and ieee2BaseTLR or ieee10PassTSO and
         ieee10PassTSR)."
 
       OBJECT      efmCuTargetSnrMgn
       MIN-ACCESS  read-only
       DESCRIPTION
         "Write access is OPTIONAL.  For PHYs without write access,
         the target SNR margin SHALL be fixed at 5dB for 2BASE-TL
         and 6dB for 10PASS-TS."
 
       OBJECT      efmCuAdaptiveSpectra
       MIN-ACCESS  read-only
       DESCRIPTION
         "Write access is OPTIONAL.  For PHYs without write access,
         the default value SHOULD be false."
 
     ::= { efmCuCompliances 1 }
END