DOCS-IETF-CABLE-DEVICE-NOTIFICATION-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2 FROM SNMPv2-SMI -- RFC 2578 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC 2580 docsDevEvLevel, docsDevEvId, docsDevEvText, docsDevSwFilename, docsDevSwServer, docsDevServerDhcp, docsDevServerTime FROM DOCS-CABLE-DEVICE-MIB -- RFC 2669 docsIfCmCmtsAddress, docsIfCmtsCmStatusMacAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType, docsIfCmtsCmStatusDocsisRegMode, docsIfCmtsCmStatusModulationType FROM DOCS-IF-MIB -- RFC 4546 ifPhysAddress FROM IF-MIB; -- RFC 2863 docsDevNotifMIB MODULE-IDENTITY LAST-UPDATED "200605240000Z" -- May 24, 2006 ORGANIZATION "IETF IP over Cable Data Network Working Group" CONTACT-INFO " Azlina Ahmad Postal: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134, U.S.A. Phone: 408 853 7927 E-mail: azlina@cisco.com Greg Nakanishi Postal: Motorola 6450 Sequence Drive San Diego, CA 92121, U.S.A. Phone: 858 404 2366 E-mail: gnakanishi@motorola.com IETF IPCDN Working Group General Discussion: ipcdn@ietf.org Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn Co-chairs: Richard Woundy, richard_woundy@cable.comcast.com Jean-Francois Mule, jf.mule@cablelabs.com" DESCRIPTION "The Event Notification MIB is an extension of the CABLE DEVICE MIB. It defines various notification objects for both cable modem and cable modem termination systems. Two groups of SNMP notification objects are defined. One group is for notifying cable modem events, and one group is for notifying cable modem termination system events. DOCSIS defines numerous events, and each event is assigned to a functional category. This MIB defines a notification object for each functional category. The varbinding list of each notification includes information about the event that occurred on the device. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4547; see the RFC itself for full legal notices." REVISION "200605240000Z" -- May 24, 2006 DESCRIPTION "Initial version, published as RFC 4547." ::= { mib-2 132 } docsDevNotifControl OBJECT IDENTIFIER ::= { docsDevNotifMIB 1} docsDevCmNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 2 0 } docsDevCmtsNotifs OBJECT IDENTIFIER ::= { docsDevNotifMIB 3 0 } docsDevCmNotifControl OBJECT-TYPE SYNTAX BITS { cmInitTLVUnknownNotif( 0), cmDynServReqFailNotif( 1), cmDynServRspFailNotif( 2), cmDynServAckFailNotif( 3), cmBpiInitNotif( 4), cmBPKMNotif( 5), cmDynamicSANotif( 6), cmDHCPFailNotif( 7), cmSwUpgradeInitNotif( 8), cmSwUpgradeFailNotif( 9), cmSwUpgradeSuccessNotif( 10), cmSwUpgradeCVCNotif( 11), cmTODFailNotif( 12), cmDCCReqFailNotif( 13), cmDCCRspFailNotif( 14), cmDCCAckFailNotif( 15) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object is used to enable specific CM notifications. For example, if the first bit is set, then docsDevCmInitTLVUnknownNotif is enabled. If it is not set, the notification is disabled. Note that notifications are also under the control of the MIB modules defined in RFC3413. If the device is rebooted,the value of this object SHOULD revert to the default value. " DEFVAL { {} } ::= { docsDevNotifControl 1 } docsDevCmtsNotifControl OBJECT-TYPE SYNTAX BITS { cmtsInitRegReqFailNotif( 0), cmtsInitRegRspFailNotif( 1), cmtsInitRegAckFailNotif( 2), cmtsDynServReqFailNotif( 3), cmtsDynServRspFailNotif( 4), cmtsDynServAckFailNotif( 5), cmtsBpiInitNotif( 6), cmtsBPKMNotif( 7), cmtsDynamicSANotif( 8), cmtsDCCReqFailNotif( 9), cmtsDCCRspFailNotif( 10), cmtsDCCAckFailNotif( 11) } MAX-ACCESS read-write STATUS current DESCRIPTION "The object is used to enable specific CMTS notifications. For example, if the first bit is set, then docsDevCmtsInitRegRspFailNotif is enabled. If it is not set, the notification is disabled. Note that notifications are also under the control of the MIB modules defined in RFC3413. If the device is rebooted,the value of this object SHOULD revert to the default value. " DEFVAL { {} } ::= { docsDevNotifControl 2 } docsDevCmInitTLVUnknownNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "Notification to indicate that an unknown TLV was encountered during the TLV parsing process. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 1 } docsDevCmDynServReqFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic service request during the dynamic services process. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected to (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 2 } docsDevCmDynServRspFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION " A notification to report the failure of a dynamic service response during the dynamic services process. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 3} docsDevCmDynServAckFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic service acknowledgement during the dynamic services process. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 4} docsDevCmBpiInitNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a BPI initialization attempt during the registration process. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 5 } docsDevCmBPKMNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a Baseline Privacy Key Management (BPKM) operation. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 6 } docsDevCmDynamicSANotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic security association operation. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 7 } docsDevCmDHCPFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsDevServerDhcp, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a DHCP operation. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsDevServerDhcp: the IP address of the DHCP server. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 8 } docsDevCmSwUpgradeInitNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsDevSwFilename, docsDevSwServer, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to indicate that a software upgrade has been initiated on the device. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 9 } docsDevCmSwUpgradeFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsDevSwFilename, docsDevSwServer, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a software upgrade attempt. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsDevSwFilename: the software image file name - docsDevSwServer: the IP address of the server that the image is retrieved from. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 10 } docsDevCmSwUpgradeSuccessNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsDevSwFilename, docsDevSwServer, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the software upgrade success status. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsDevSwFilename: the software image file name - docsDevSwServer: the IP address of the server that the image is retrieved from. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 11 } docsDevCmSwUpgradeCVCFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report that the verification of the code file has failed during a secure software upgrade attempt. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 12 } docsDevCmTODFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsDevServerTime, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a time of day operation. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsDevServerTime: the IP address of the time server. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 13 } docsDevCmDCCReqFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION " A notification to report the failure of a dynamic channel change request during the dynamic channel change process on the CM. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 14 } docsDevCmDCCRspFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic channel change response during the dynamic channel change process on the CM. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 15 } docsDevCmDCCAckFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, ifPhysAddress, docsIfCmCmtsAddress, docsIfDocsisBaseCapability, docsIfCmStatusDocsisOperMode, docsIfCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic channel change acknowledgement during the dynamic channel change process on the CM. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - ifPhysAddress: the MAC address of the cable interface of this cable modem. - docsIfCmCmtsAddress: the MAC address of the CMTS to which the CM is connected (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface to which it is connected). - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmStatusDocsisOperMode: the QOS level (1.0, 1.1) that the CM is operating in. - docsIfCmtsCmStatusModulationType the upstream modulation methodology used by the CM. " ::= { docsDevCmNotifs 16} docsDevCmtsInitRegReqFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a registration request from a CM during the CM initialization process that was detected on the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 1 } docsDevCmtsInitRegRspFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a registration response during the CM initialization process that was detected by the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 2 } docsDevCmtsInitRegAckFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a registration acknowledgement from the CM during the CM initialization process that was detected by the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 3 } docsDevCmtsDynServReqFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic service request during the dynamic services process that was detected by the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 4 } docsDevCmtsDynServRspFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic service response during the dynamic services process that was detected by the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 5 } docsDevCmtsDynServAckFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic service acknowledgement during the dynamic services process that was detected by the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 6 } docsDevCmtsBpiInitNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a BPI initialization attempt during the CM registration process that was detected by the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 7 } docsDevCmtsBPKMNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a BPKM operation that is detected by the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 8 } docsDevCmtsDynamicSANotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic security association operation that is detected by the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 9 } docsDevCmtsDCCReqFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic channel change request during the dynamic channel change process and is detected by the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 10 } docsDevCmtsDCCRspFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic channel change response during the dynamic channel change process and is detected by the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 11 } docsDevCmtsDCCAckFailNotif NOTIFICATION-TYPE OBJECTS { docsDevEvLevel, docsDevEvId, docsDevEvText, docsIfCmtsCmStatusMacAddress, ifPhysAddress, docsIfCmtsCmStatusDocsisRegMode, docsIfDocsisBaseCapability, docsIfCmtsCmStatusModulationType } STATUS current DESCRIPTION "A notification to report the failure of a dynamic channel change acknowledgement during the dynamic channel change process and is detected by the CMTS. This notification sends additional information about the event by including the following objects in its varbinding list. - docsDevEvLevel: the priority level associated with the event. - docsDevEvId: the unique identifier of the event that occurred. - docsDevEvText: a textual description of the event. - docsIfCmtsCmStatusMacAddress: the MAC address of the CM with which this notification is associated. - ifPhysAddress: the MAC address of the CMTS (if there is a cable card/interface in the CMTS, then it is actually the MAC address of the cable interface that connected to the CM) cable interface connected to the CM. - docsIfCmtsCmStatusDocsisRegMode: the QOS level (1.0, 1.1) that the reporting CM is operating in. - docsIfDocsisBaseCapability: the highest version of the DOCSIS specification (1.0, 1.1, 2.0) that the device is capable of supporting. - docsIfCmtsCmStatusModulationType: the upstream modulation methodology used by the CM. " ::= { docsDevCmtsNotifs 12} -- --Conformance definitions -- docsDevNotifConformance OBJECT IDENTIFIER ::= { docsDevNotifMIB 4 } docsDevNotifGroups OBJECT IDENTIFIER ::= { docsDevNotifConformance 1 } docsDevNotifCompliances OBJECT IDENTIFIER ::= { docsDevNotifConformance 2 } docsDevCmNotifCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for CM Notifications and Control." MODULE --docsDevNotif MANDATORY-GROUPS { docsDevCmNotifControlGroup, docsDevCmNotificationGroup } ::= { docsDevNotifCompliances 1 } docsDevCmNotifControlGroup OBJECT-GROUP OBJECTS { docsDevCmNotifControl } STATUS current DESCRIPTION "This group represents objects that allow control over CM Notifications." ::= { docsDevNotifGroups 1 } docsDevCmNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { docsDevCmInitTLVUnknownNotif, docsDevCmDynServReqFailNotif, docsDevCmDynServRspFailNotif, docsDevCmDynServAckFailNotif, docsDevCmBpiInitNotif, docsDevCmBPKMNotif, docsDevCmDynamicSANotif, docsDevCmDHCPFailNotif, docsDevCmSwUpgradeInitNotif, docsDevCmSwUpgradeFailNotif, docsDevCmSwUpgradeSuccessNotif, docsDevCmSwUpgradeCVCFailNotif, docsDevCmTODFailNotif, docsDevCmDCCReqFailNotif, docsDevCmDCCRspFailNotif, docsDevCmDCCAckFailNotif } STATUS current DESCRIPTION "A collection of CM notifications providing device status and control." ::= { docsDevNotifGroups 2 } docsDevCmtsNotifCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for DOCSIS CMTS Notification and Control." MODULE --docsDevNotif MANDATORY-GROUPS { docsDevCmtsNotifControlGroup, docsDevCmtsNotificationGroup } ::= { docsDevNotifCompliances 2 } docsDevCmtsNotifControlGroup OBJECT-GROUP OBJECTS { docsDevCmtsNotifControl } STATUS current DESCRIPTION "This group represents objects that allow control over CMTS Notifications." ::= { docsDevNotifGroups 3 } docsDevCmtsNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { docsDevCmtsInitRegReqFailNotif, docsDevCmtsInitRegRspFailNotif, docsDevCmtsInitRegAckFailNotif , docsDevCmtsDynServReqFailNotif, docsDevCmtsDynServRspFailNotif, docsDevCmtsDynServAckFailNotif, docsDevCmtsBpiInitNotif, docsDevCmtsBPKMNotif, docsDevCmtsDynamicSANotif, docsDevCmtsDCCReqFailNotif, docsDevCmtsDCCRspFailNotif, docsDevCmtsDCCAckFailNotif } STATUS current DESCRIPTION "A collection of CMTS notifications providing device status and control." ::= { docsDevNotifGroups 4 } END