DISMAN-TRACEROUTE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Gauge32, Unsigned32, mib-2, NOTIFICATION-TYPE, OBJECT-IDENTITY FROM SNMPv2-SMI -- RFC2578 RowStatus, StorageType, TruthValue, DateAndTime FROM SNMPv2-TC -- RFC2579 MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- RFC2580 SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- RFC3411 InterfaceIndexOrZero -- RFC2863 FROM IF-MIB InetAddressType, InetAddress FROM INET-ADDRESS-MIB -- RFC4001 OperationResponseStatus FROM DISMAN-PING-MIB; -- RFC4560 traceRouteMIB MODULE-IDENTITY LAST-UPDATED "200606130000Z" -- 13 June 2006 ORGANIZATION "IETF Distributed Management Working Group" CONTACT-INFO "Juergen Quittek NEC Europe Ltd. Network Laboratories Kurfuersten-Anlage 36 69115 Heidelberg Germany Phone: +49 6221 4342-115 Email: quittek@netlab.nec.de" DESCRIPTION "The Traceroute MIB (DISMAN-TRACEROUTE-MIB) provides access to the traceroute capability at a remote host. Copyright (C) The Internet Society (2006). This version of this MIB module is part of RFC 4560; see the RFC itself for full legal notices." -- Revision history REVISION "200606130000Z" -- 13 June 2006 DESCRIPTION "Updated version, published as RFC 4560. - Correctly considered IPv6 in DESCRIPTION clause of object traceRouteCtlDataSize - Replaced references to RFC 2575 by RFC 3415 - Replaced references to RFC 2571 by RFC 3411 - Replaced references to RFC 2851 by RFC 4001 - Clarified DESCRIPTION clause of object traceRouteResultsLastGoodPath - Changed range of object traceRouteCtlInitialTtl from (0..255) to (1..255) - Extended DESCRIPTION clause of traceRouteResultsTable describing re-initialization of entries - Changed SYNTAX of traceRouteResultsTestAttempts and traceRouteResultsTestSuccesses from Unsigned32 to Gauge32 - Changed status of traceRouteCompliance to deprecated - Added traceRouteFullCompliance and traceRouteMinimumCompliance - Changed status of traceRouteGroup and traceRouteTimeStampGroup to deprecated - Added traceRouteMinimumGroup, traceRouteCtlRowStatusGroup, and traceRouteHistoryGroup - Changed DEFVAL of object traceRouteCtlTargetAddressType from { ipv4 } to { unknown } - Changed DEFVAL of object traceRouteCtlDescr from { '00'H } to { ''H } - Added DEFVAL for object traceRouteCtlTrapGeneration of DEFVAL { { } }" REVISION "200009210000Z" -- 21 September 2000 DESCRIPTION "Initial version, published as RFC 2925." ::= { mib-2 81 } -- Top level structure of the MIB traceRouteNotifications OBJECT IDENTIFIER ::= { traceRouteMIB 0 } traceRouteObjects OBJECT IDENTIFIER ::= { traceRouteMIB 1 } traceRouteConformance OBJECT IDENTIFIER ::= { traceRouteMIB 2 } -- The registration node (point) for traceroute implementation types traceRouteImplementationTypeDomains OBJECT IDENTIFIER ::= { traceRouteMIB 3 } traceRouteUsingUdpProbes OBJECT-IDENTITY STATUS current DESCRIPTION "Indicates that an implementation is using UDP probes to perform the traceroute operation." ::= { traceRouteImplementationTypeDomains 1 } -- Simple Object Definitions traceRouteMaxConcurrentRequests OBJECT-TYPE SYNTAX Unsigned32 UNITS "requests" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of concurrent active traceroute requests that are allowed within an agent implementation. A value of 0 for this object implies that there is no limit for the number of concurrent active requests in effect. The limit applies only to new requests being activated. When a new value is set, the agent will continue processing all the requests already active, even if their number exceeds the limit just imposed." DEFVAL { 10 } ::= { traceRouteObjects 1 } -- Traceroute Control Table traceRouteCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF TraceRouteCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines the Remote Operations Traceroute Control Table for providing the capability of invoking traceroute from a remote host. The results of traceroute operations can be stored in the traceRouteResultsTable, traceRouteProbeHistoryTable, and the traceRouteHopsTable." ::= { traceRouteObjects 2 } traceRouteCtlEntry OBJECT-TYPE SYNTAX TraceRouteCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines an entry in the traceRouteCtlTable. The first index element, traceRouteCtlOwnerIndex, is of type SnmpAdminString, a textual convention that allows for use of the SNMPv3 View-Based Access Control Model (RFC 3415, VACM) and that allows a management application to identify its entries. The second index, traceRouteCtlTestName (also an SnmpAdminString), enables the same management application to have multiple requests outstanding." INDEX { traceRouteCtlOwnerIndex, traceRouteCtlTestName } ::= { traceRouteCtlTable 1 } TraceRouteCtlEntry ::= SEQUENCE { traceRouteCtlOwnerIndex SnmpAdminString, traceRouteCtlTestName SnmpAdminString, traceRouteCtlTargetAddressType InetAddressType, traceRouteCtlTargetAddress InetAddress, traceRouteCtlByPassRouteTable TruthValue, traceRouteCtlDataSize Unsigned32, traceRouteCtlTimeOut Unsigned32, traceRouteCtlProbesPerHop Unsigned32, traceRouteCtlPort Unsigned32, traceRouteCtlMaxTtl Unsigned32, traceRouteCtlDSField Unsigned32, traceRouteCtlSourceAddressType InetAddressType, traceRouteCtlSourceAddress InetAddress, traceRouteCtlIfIndex InterfaceIndexOrZero, traceRouteCtlMiscOptions SnmpAdminString, traceRouteCtlMaxFailures Unsigned32, traceRouteCtlDontFragment TruthValue, traceRouteCtlInitialTtl Unsigned32, traceRouteCtlFrequency Unsigned32, traceRouteCtlStorageType StorageType, traceRouteCtlAdminStatus INTEGER, traceRouteCtlDescr SnmpAdminString, traceRouteCtlMaxRows Unsigned32, traceRouteCtlTrapGeneration BITS, traceRouteCtlCreateHopsEntries TruthValue, traceRouteCtlType OBJECT IDENTIFIER, traceRouteCtlRowStatus RowStatus } traceRouteCtlOwnerIndex OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model (RFC 3415, VACM) for tables in which multiple users may need to create or modify entries independently, the initial index is used as an 'owner index'. Such an initial index has a syntax of SnmpAdminString and can thus be trivially mapped to a securityName or groupName defined in VACM, in accordance with a security policy. When used in conjunction with such a security policy, all entries in the table belonging to a particular user (or group) will have the same value for this initial index. For a given user's entries in a particular table, the object identifiers for the information in these entries will have the same subidentifiers (except for the 'column' subidentifier) up to the end of the encoded owner index. To configure VACM to permit access to this portion of the table, one would create vacmViewTreeFamilyTable entries with the value of vacmViewTreeFamilySubtree including the owner index portion, and vacmViewTreeFamilyMask 'wildcarding' the column subidentifier. More elaborate configurations are possible." ::= { traceRouteCtlEntry 1 } traceRouteCtlTestName OBJECT-TYPE SYNTAX SnmpAdminString (SIZE(0..32)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a traceroute test. This is locally unique, within the scope of a traceRouteCtlOwnerIndex." ::= { traceRouteCtlEntry 2 } traceRouteCtlTargetAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the type of host address to be used on the traceroute request at the remote host." DEFVAL { unknown } ::= { traceRouteCtlEntry 3 } traceRouteCtlTargetAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the host address used on the traceroute request at the remote host. The host address type can be determined by examining the value of the corresponding traceRouteCtlTargetAddressType. A value for this object MUST be set prior to transitioning its corresponding traceRouteCtlEntry to active(1) via traceRouteCtlRowStatus." ::= { traceRouteCtlEntry 4 } traceRouteCtlByPassRouteTable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "The purpose of this object is to enable optional bypassing the route table. If enabled, the remote host will bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly attached network, an error is returned. This option can be used to perform the traceroute operation to a local host through an interface that has no route defined (e.g., after the interface was dropped by the routing daemon at the host)." DEFVAL { false } ::= { traceRouteCtlEntry 5 } traceRouteCtlDataSize OBJECT-TYPE SYNTAX Unsigned32 (0..65507) UNITS "octets" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the size of the data portion of a traceroute request, in octets. If the RECOMMENDED traceroute method (UDP datagrams as probes) is used, then the value contained in this object MUST be applied. If another traceroute method is used for which the specified size is not appropriate, then the implementation SHOULD use whatever size (appropriate to the method) is closest to the specified size. The maximum value for this object was computed by subtracting the smallest possible IP header size of 20 octets (IPv4 header with no options) and the UDP header size of 8 octets from the maximum IP packet size. An IP packet has a maximum size of 65535 octets (excluding IPv6 Jumbograms)." DEFVAL { 0 } ::= { traceRouteCtlEntry 6 } traceRouteCtlTimeOut OBJECT-TYPE SYNTAX Unsigned32 (1..60) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the time-out value, in seconds, for a traceroute request." DEFVAL { 3 } ::= { traceRouteCtlEntry 7 } traceRouteCtlProbesPerHop OBJECT-TYPE SYNTAX Unsigned32 (1..10) UNITS "probes" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the number of times to reissue a traceroute request with the same time-to-live (TTL) value." DEFVAL { 3 } ::= { traceRouteCtlEntry 8 } traceRouteCtlPort OBJECT-TYPE SYNTAX Unsigned32 (1..65535) UNITS "UDP Port" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the (initial) UDP port to send the traceroute request to. A port needs to be specified that is not in use at the destination (target) host. The default value for this object is the IANA assigned port, 33434, for the traceroute function." DEFVAL { 33434 } ::= { traceRouteCtlEntry 9 } traceRouteCtlMaxTtl OBJECT-TYPE SYNTAX Unsigned32 (1..255) UNITS "time-to-live value" MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the maximum time-to-live value." DEFVAL { 30 } ::= { traceRouteCtlEntry 10 } traceRouteCtlDSField OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the value to store in the Type of Service (TOS) octet in the IPv4 header or in the Traffic Class octet in the IPv6 header, respectively, of the IP packet used to encapsulate the traceroute probe. The octet to be set in the IP header contains the Differentiated Services (DS) Field in the six most significant bits. This option can be used to determine what effect an explicit DS Field setting has on a traceroute response. Not all values are legal or meaningful. A value of 0 means that the function represented by this option is not supported. DS Field usage is often not supported by IP implementations, and not all values are supported. Refer to RFC 2474 and RFC 3260 for guidance on usage of this field." REFERENCE "Refer to RFC 1812 for the definition of the IPv4 TOS octet and to RFC 2460 for the definition of the IPv6 Traffic Class octet. Refer to RFC 2474 and RFC 3260 for the definition of the Differentiated Services Field." DEFVAL { 0 } ::= { traceRouteCtlEntry 11 } traceRouteCtlSourceAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the type of the source address, traceRouteCtlSourceAddress, to be used at a remote host when a traceroute operation is performed." DEFVAL { unknown } ::= { traceRouteCtlEntry 12 } traceRouteCtlSourceAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "Use the specified IP address (which must be given as an IP number, not a hostname) as the source address in outgoing probe packets. On hosts with more than one IP address, this option can be used to select the address to be used. If the IP address is not one of this machine's interface addresses, an error is returned, and nothing is sent. A zero-length octet string value for this object disables source address specification. The address type (InetAddressType) that relates to this object is specified by the corresponding value of traceRouteCtlSourceAddressType." DEFVAL { ''H } ::= { traceRouteCtlEntry 13 } traceRouteCtlIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this object to an interface's ifIndex prior to starting a remote traceroute operation directs the traceroute probes to be transmitted over the specified interface. A value of zero for this object implies that this option is not enabled." DEFVAL { 0 } ::= { traceRouteCtlEntry 14 } traceRouteCtlMiscOptions OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "Enables an application to specify implementation-dependent options." DEFVAL { ''H } ::= { traceRouteCtlEntry 15 } traceRouteCtlMaxFailures OBJECT-TYPE SYNTAX Unsigned32 (0..255) UNITS "timeouts" MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object indicates the maximum number of consecutive timeouts allowed before a remote traceroute request is terminated. A value of either 255 (maximum hop count/possible TTL value) or 0 indicates that the function of terminating a remote traceroute request when a specific number of consecutive timeouts are detected is disabled." DEFVAL { 5 } ::= { traceRouteCtlEntry 16 } traceRouteCtlDontFragment OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This object enables setting of the don't fragment flag (DF) in the IP header for a probe. Use of this object enables a manual PATH MTU test is performed." DEFVAL { false } ::= { traceRouteCtlEntry 17 } traceRouteCtlInitialTtl OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object specifies the initial TTL value to use. This enables bypassing the initial (often well known) portion of a path." DEFVAL { 1 } ::= { traceRouteCtlEntry 18 } traceRouteCtlFrequency OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The number of seconds to wait before repeating a traceroute test, as defined by the value of the various objects in the corresponding row. After a single test is completed the number of seconds as defined by the value of traceRouteCtlFrequency MUST elapse before the next traceroute test is started. A value of 0 for this object implies that the test as defined by the corresponding entry will not be repeated." DEFVAL { 0 } ::= { traceRouteCtlEntry 19 } traceRouteCtlStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-create STATUS current DESCRIPTION "The storage type for this conceptual row. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row." DEFVAL { nonVolatile } ::= { traceRouteCtlEntry 20 } traceRouteCtlAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), -- operation should be started disabled(2) -- operation should be stopped } MAX-ACCESS read-create STATUS current DESCRIPTION "Reflects the desired state that an traceRouteCtlEntry should be in: enabled(1) - Attempt to activate the test as defined by this traceRouteCtlEntry. disabled(2) - Deactivate the test as defined by this traceRouteCtlEntry. Refer to the corresponding traceRouteResultsOperStatus to determine the operational state of the test defined by this entry." DEFVAL { disabled } ::= { traceRouteCtlEntry 21 } traceRouteCtlDescr OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-create STATUS current DESCRIPTION "The purpose of this object is to provide a descriptive name of the remote traceroute test." DEFVAL { ''H } ::= { traceRouteCtlEntry 22 } traceRouteCtlMaxRows OBJECT-TYPE SYNTAX Unsigned32 UNITS "rows" MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of corresponding entries allowed in the traceRouteProbeHistoryTable. An implementation of this MIB will remove the oldest corresponding entry in the traceRouteProbeHistoryTable to allow the addition of an new entry once the number of corresponding rows in the traceRouteProbeHistoryTable reaches this value. Old entries are not removed when a new test is started. Entries are added to the traceRouteProbeHistoryTable until traceRouteCtlMaxRows is reached before entries begin to be removed. A value of 0 for this object disables creation of traceRouteProbeHistoryTable entries." DEFVAL { 50 } ::= { traceRouteCtlEntry 23 } traceRouteCtlTrapGeneration OBJECT-TYPE SYNTAX BITS { pathChange(0), testFailure(1), testCompletion(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object determines when and whether to generate a notification for this entry: pathChange(0) - Generate a traceRoutePathChange notification when the current path varies from a previously determined path. testFailure(1) - Generate a traceRouteTestFailed notification when the full path to a target can't be determined. testCompletion(2) - Generate a traceRouteTestCompleted notification when the path to a target has been determined. The value of this object defaults to an empty set, indicating that none of the above options has been selected." DEFVAL { { } } ::= { traceRouteCtlEntry 24 } traceRouteCtlCreateHopsEntries OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "The current path for a traceroute test is kept in the traceRouteHopsTable on a per-hop basis when the value of this object is true(1)." DEFVAL { false } ::= { traceRouteCtlEntry 25 } traceRouteCtlType OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "The value of this object is used either to report or to select the implementation method to be used for performing a traceroute operation. The value of this object may be selected from traceRouteImplementationTypeDomains. Additional implementation types should be allocated as required by implementers of the DISMAN-TRACEROUTE-MIB under their enterprise specific registration point, not beneath traceRouteImplementationTypeDomains." DEFVAL { traceRouteUsingUdpProbes } ::= { traceRouteCtlEntry 26 } traceRouteCtlRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object allows entries to be created and deleted in the traceRouteCtlTable. Deletion of an entry in this table results in a deletion of all corresponding (same traceRouteCtlOwnerIndex and traceRouteCtlTestName index values) traceRouteResultsTable, traceRouteProbeHistoryTable, and traceRouteHopsTable entries. A value MUST be specified for traceRouteCtlTargetAddress prior to acceptance of a transition to active(1) state. When a value for pingCtlTargetAddress is set, the value of object pingCtlRowStatus changes from notReady(3) to notInService(2). Activation of a remote traceroute operation is controlled via traceRouteCtlAdminStatus, and not by transitioning of this object's value to active(1). Transitions in and out of active(1) state are not allowed while an entry's traceRouteResultsOperStatus is active(1), with the exception that deletion of an entry in this table by setting its RowStatus object to destroy(6) will stop an active traceroute operation. The operational state of an traceroute operation can be determined by examination of the corresponding traceRouteResultsOperStatus object." REFERENCE "See definition of RowStatus in RFC 2579, 'Textual Conventions for SMIv2.'" ::= { traceRouteCtlEntry 27 } -- Traceroute Results Table traceRouteResultsTable OBJECT-TYPE SYNTAX SEQUENCE OF TraceRouteResultsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines the Remote Operations Traceroute Results Table for keeping track of the status of a traceRouteCtlEntry. An entry is added to the traceRouteResultsTable when an traceRouteCtlEntry is started by successful transition of its traceRouteCtlAdminStatus object to enabled(1). If the object traceRouteCtlAdminStatus already has the value enabled(1), and if the corresponding traceRouteResultsOperStatus object has the value completed(3), then successfully writing enabled(1) to the object traceRouteCtlAdminStatus re-initializes the already existing entry in the traceRouteResultsTable. The values of objects in the re-initialized entry are the same as the values of objects in a new entry would be. An entry is removed from the traceRouteResultsTable when its corresponding traceRouteCtlEntry is deleted." ::= { traceRouteObjects 3 } traceRouteResultsEntry OBJECT-TYPE SYNTAX TraceRouteResultsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines an entry in the traceRouteResultsTable. The traceRouteResultsTable has the same indexing as the traceRouteCtlTable so that a traceRouteResultsEntry corresponds to the traceRouteCtlEntry that caused it to be created." INDEX { traceRouteCtlOwnerIndex, traceRouteCtlTestName } ::= { traceRouteResultsTable 1 } TraceRouteResultsEntry ::= SEQUENCE { traceRouteResultsOperStatus INTEGER, traceRouteResultsCurHopCount Gauge32, traceRouteResultsCurProbeCount Gauge32, traceRouteResultsIpTgtAddrType InetAddressType, traceRouteResultsIpTgtAddr InetAddress, traceRouteResultsTestAttempts Gauge32, traceRouteResultsTestSuccesses Gauge32, traceRouteResultsLastGoodPath DateAndTime } traceRouteResultsOperStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), -- test is in progress disabled(2), -- test has stopped completed(3) -- test is completed } MAX-ACCESS read-only STATUS current DESCRIPTION "Reflects the operational state of an traceRouteCtlEntry: enabled(1) - Test is active. disabled(2) - Test has stopped. completed(3) - Test is completed." ::= { traceRouteResultsEntry 1 } traceRouteResultsCurHopCount OBJECT-TYPE SYNTAX Gauge32 UNITS "hops" MAX-ACCESS read-only STATUS current DESCRIPTION "Reflects the current TTL value (from 1 to 255) for a remote traceroute operation. Maximum TTL value is determined by traceRouteCtlMaxTtl." ::= { traceRouteResultsEntry 2 } traceRouteResultsCurProbeCount OBJECT-TYPE SYNTAX Gauge32 UNITS "probes" MAX-ACCESS read-only STATUS current DESCRIPTION "Reflects the current probe count (1..10) for a remote traceroute operation. The maximum probe count is determined by traceRouteCtlProbesPerHop." ::= { traceRouteResultsEntry 3 } traceRouteResultsIpTgtAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of address stored in the corresponding traceRouteResultsIpTgtAddr object." ::= { traceRouteResultsEntry 4 } traceRouteResultsIpTgtAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object reports the IP address associated with a traceRouteCtlTargetAddress value when the destination address is specified as a DNS name. The value of this object should be a zero-length octet string when a DNS name is not specified or when a specified DNS name fails to resolve." ::= { traceRouteResultsEntry 5 } traceRouteResultsTestAttempts OBJECT-TYPE SYNTAX Gauge32 UNITS "tests" MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of attempts to determine a path to a target. The value of this object MUST be started at 0." ::= { traceRouteResultsEntry 6 } traceRouteResultsTestSuccesses OBJECT-TYPE SYNTAX Gauge32 UNITS "tests" MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of attempts to determine a path to a target that have succeeded. The value of this object MUST be reported as 0 when no attempts have succeeded." ::= { traceRouteResultsEntry 7 } traceRouteResultsLastGoodPath OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The date and time when the last complete path was determined. A path is complete if responses were received or timeout occurred for each hop on the path; i.e., for each TTL value from the value of the corresponding traceRouteCtlInitialTtl object up to the end of the path or (if no reply from the target IP address was received) up to the value of the corresponding traceRouteCtlMaxTtl object." ::= { traceRouteResultsEntry 8 } -- Trace Route Probe History Table traceRouteProbeHistoryTable OBJECT-TYPE SYNTAX SEQUENCE OF TraceRouteProbeHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines the Remote Operations Traceroute Results Table for storing the results of a traceroute operation. An implementation of this MIB will remove the oldest entry in the traceRouteProbeHistoryTable of the corresponding entry in the traceRouteCtlTable to allow the addition of a new entry once the number of rows in the traceRouteProbeHistoryTable reaches the value specified by traceRouteCtlMaxRows for the corresponding entry in the traceRouteCtlTable." ::= { traceRouteObjects 4 } traceRouteProbeHistoryEntry OBJECT-TYPE SYNTAX TraceRouteProbeHistoryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines a table for storing the results of a traceroute operation. Entries in this table are limited by the value of the corresponding traceRouteCtlMaxRows object. The first two index elements identify the traceRouteCtlEntry that a traceRouteProbeHistoryEntry belongs to. The third index element selects a single traceroute operation result. The fourth and fifth indexes select the hop and the probe for a particular traceroute operation." INDEX { traceRouteCtlOwnerIndex, traceRouteCtlTestName, traceRouteProbeHistoryIndex, traceRouteProbeHistoryHopIndex, traceRouteProbeHistoryProbeIndex } ::= { traceRouteProbeHistoryTable 1 } TraceRouteProbeHistoryEntry ::= SEQUENCE { traceRouteProbeHistoryIndex Unsigned32, traceRouteProbeHistoryHopIndex Unsigned32, traceRouteProbeHistoryProbeIndex Unsigned32, traceRouteProbeHistoryHAddrType InetAddressType, traceRouteProbeHistoryHAddr InetAddress, traceRouteProbeHistoryResponse Unsigned32, traceRouteProbeHistoryStatus OperationResponseStatus, traceRouteProbeHistoryLastRC Integer32, traceRouteProbeHistoryTime DateAndTime } traceRouteProbeHistoryIndex OBJECT-TYPE SYNTAX Unsigned32 (1..'ffffffff'h) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table is created when the result of a traceroute probe is determined. The initial 2 instance identifier index values identify the traceRouteCtlEntry that a probe result (traceRouteProbeHistoryEntry) belongs to. An entry is removed from this table when its corresponding traceRouteCtlEntry is deleted. An implementation MUST start assigning traceRouteProbeHistoryIndex values at 1 and wrap after exceeding the maximum possible value, as defined by the limit of this object ('ffffffff'h)." ::= { traceRouteProbeHistoryEntry 1 } traceRouteProbeHistoryHopIndex OBJECT-TYPE SYNTAX Unsigned32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicates which hop in a traceroute path the probe's results are for. The value of this object is initially determined by the value of traceRouteCtlInitialTtl." ::= { traceRouteProbeHistoryEntry 2 } traceRouteProbeHistoryProbeIndex OBJECT-TYPE SYNTAX Unsigned32 (1..10) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Indicates the index of a probe for a particular hop in a traceroute path. The number of probes per hop is determined by the value of the corresponding traceRouteCtlProbesPerHop object." ::= { traceRouteProbeHistoryEntry 3 } traceRouteProbeHistoryHAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This objects indicates the type of address stored in the corresponding traceRouteProbeHistoryHAddr object." ::= { traceRouteProbeHistoryEntry 4 } traceRouteProbeHistoryHAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The address of a hop in a traceroute path. This object is not allowed to be a DNS name. The value of the corresponding object, traceRouteProbeHistoryHAddrType, indicates this object's IP address type." ::= { traceRouteProbeHistoryEntry 5 } traceRouteProbeHistoryResponse OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The amount of time measured in milliseconds from when a probe was sent to when its response was received or when it timed out. The value of this object is reported as 0 when it is not possible to transmit a probe." ::= { traceRouteProbeHistoryEntry 6 } traceRouteProbeHistoryStatus OBJECT-TYPE SYNTAX OperationResponseStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The result of a traceroute operation made by a remote host for a particular probe." ::= { traceRouteProbeHistoryEntry 7 } traceRouteProbeHistoryLastRC OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The last implementation-method-specific reply code received. Traceroute is usually implemented by transmitting a series of probe packets with increasing time-to-live values. A probe packet is a UDP datagram encapsulated into an IP packet. Each hop in a path to the target (destination) host rejects the probe packets (probe's TTL too small, ICMP reply) until either the maximum TTL is exceeded or the target host is received." ::= { traceRouteProbeHistoryEntry 8 } traceRouteProbeHistoryTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Timestamp for when this probe's results were determined." ::= { traceRouteProbeHistoryEntry 9 } -- Traceroute Hop Results Table traceRouteHopsTable OBJECT-TYPE SYNTAX SEQUENCE OF TraceRouteHopsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines the Remote Operations Traceroute Hop Table for keeping track of the results of traceroute tests on a per-hop basis." ::= { traceRouteObjects 5 } traceRouteHopsEntry OBJECT-TYPE SYNTAX TraceRouteHopsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Defines an entry in the traceRouteHopsTable. The first two index elements identify the traceRouteCtlEntry that a traceRouteHopsEntry belongs to. The third index element, traceRouteHopsHopIndex, selects a hop in a traceroute path." INDEX { traceRouteCtlOwnerIndex, traceRouteCtlTestName, traceRouteHopsHopIndex } ::= { traceRouteHopsTable 1 } TraceRouteHopsEntry ::= SEQUENCE { traceRouteHopsHopIndex Unsigned32, traceRouteHopsIpTgtAddressType InetAddressType, traceRouteHopsIpTgtAddress InetAddress, traceRouteHopsMinRtt Unsigned32, traceRouteHopsMaxRtt Unsigned32, traceRouteHopsAverageRtt Unsigned32, traceRouteHopsRttSumOfSquares Unsigned32, traceRouteHopsSentProbes Unsigned32, traceRouteHopsProbeResponses Unsigned32, traceRouteHopsLastGoodProbe DateAndTime } traceRouteHopsHopIndex OBJECT-TYPE SYNTAX Unsigned32 (1..'ffffffff'h) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specifies the hop index for a traceroute hop. Values for this object with respect to the same traceRouteCtlOwnerIndex and traceRouteCtlTestName MUST start at 1 and be given increasing values for subsequent hops. The value of traceRouteHopsHopIndex is not necessarily the number of the hop on the traced path. The traceRouteHopsTable keeps the current traceroute path per traceRouteCtlEntry if enabled by setting the corresponding traceRouteCtlCreateHopsEntries to true(1). All hops (traceRouteHopsTable entries) in a traceroute path MUST be updated at the same time when a traceroute operation is completed. Care needs to be applied when a path either changes or can't be determined. The initial portion of the path, up to the first hop change, MUST retain the same traceRouteHopsHopIndex values. The remaining portion of the path SHOULD be assigned new traceRouteHopsHopIndex values." ::= { traceRouteHopsEntry 1 } traceRouteHopsIpTgtAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the type of address stored in the corresponding traceRouteHopsIpTgtAddress object." ::= { traceRouteHopsEntry 2 } traceRouteHopsIpTgtAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This object reports the IP address associated with the hop. A value for this object should be reported as a numeric IP address, not as a DNS name. The address type (InetAddressType) that relates to this object is specified by the corresponding value of pingCtlSourceAddressType." ::= { traceRouteHopsEntry 3 } traceRouteHopsMinRtt OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum traceroute round-trip-time (RTT) received for this hop. A value of 0 for this object implies that no RTT has been received." ::= { traceRouteHopsEntry 4 } traceRouteHopsMaxRtt OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum traceroute round-trip-time (RTT) received for this hop. A value of 0 for this object implies that no RTT has been received." ::= { traceRouteHopsEntry 5 } traceRouteHopsAverageRtt OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current average traceroute round-trip-time (RTT) for this hop." ::= { traceRouteHopsEntry 6 } traceRouteHopsRttSumOfSquares OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This object contains the sum of the squares of all round-trip-times received for this hop. Its purpose is to enable standard deviation calculation." ::= { traceRouteHopsEntry 7 } traceRouteHopsSentProbes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of this object reflects the number of probes sent for this hop during this traceroute test. The value of this object should start at 0." ::= { traceRouteHopsEntry 8 } traceRouteHopsProbeResponses OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of responses received for this hop during this traceroute test. This value of this object should start at 0." ::= { traceRouteHopsEntry 9 } traceRouteHopsLastGoodProbe OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "Date and time at which the last response was received for a probe for this hop during this traceroute test." ::= { traceRouteHopsEntry 10 } -- Notification Definition section traceRoutePathChange NOTIFICATION-TYPE OBJECTS { traceRouteCtlTargetAddressType, traceRouteCtlTargetAddress, traceRouteResultsIpTgtAddrType, traceRouteResultsIpTgtAddr } STATUS current DESCRIPTION "The path to a target has changed." ::= { traceRouteNotifications 1 } traceRouteTestFailed NOTIFICATION-TYPE OBJECTS { traceRouteCtlTargetAddressType, traceRouteCtlTargetAddress, traceRouteResultsIpTgtAddrType, traceRouteResultsIpTgtAddr } STATUS current DESCRIPTION "Could not determine the path to a target." ::= { traceRouteNotifications 2 } traceRouteTestCompleted NOTIFICATION-TYPE OBJECTS { traceRouteCtlTargetAddressType, traceRouteCtlTargetAddress, traceRouteResultsIpTgtAddrType, traceRouteResultsIpTgtAddr } STATUS current DESCRIPTION "The path to a target has just been determined." ::= { traceRouteNotifications 3 } -- Conformance information -- Compliance statements traceRouteCompliances OBJECT IDENTIFIER ::= { traceRouteConformance 1 } traceRouteGroups OBJECT IDENTIFIER ::= { traceRouteConformance 2 } -- Compliance statements traceRouteFullCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that fully implement the DISMAN-TRACEROUTE-MIB." MODULE -- this module MANDATORY-GROUPS { traceRouteMinimumGroup, traceRouteCtlRowStatusGroup, traceRouteHistoryGroup } GROUP traceRouteHopsTableGroup DESCRIPTION "This group lists the objects that make up a traceRouteHopsEntry. Support of the traceRouteHopsTable is optional." GROUP traceRouteNotificationsGroup DESCRIPTION "This group defines a collection of optional notifications." OBJECT traceRouteMaxConcurrentRequests MIN-ACCESS read-only DESCRIPTION "The agent is not required to support SET operations to this object." OBJECT traceRouteCtlByPassRouteTable MIN-ACCESS read-only DESCRIPTION "Write access to this object is not required by implementations that are not capable of its implementation. The function represented by this object is implementable if the setsockopt SOL_SOCKET SO_DONTROUTE option is supported." OBJECT traceRouteCtlDSField MIN-ACCESS read-only DESCRIPTION "Write access is not required. If write access is not supported, return a 0 as the value of this object. A value of 0 implies that the function represented by this option is not supported." OBJECT traceRouteCtlSourceAddressType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "Write access to this object is not required by implementations that are not capable of binding the send socket with a source address. An implementation is only required to support IPv4 and IPv6 addresses." OBJECT traceRouteCtlSourceAddress SYNTAX InetAddress (SIZE(0|4|16)) MIN-ACCESS read-only DESCRIPTION "Write access to this object is not required by implementations that are not capable of binding the send socket with a source address. An implementation is only required to support IPv4 and IPv6 addresses." OBJECT traceRouteCtlIfIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. If write access is not supported, return a 0 as the value of this object. A value of 0 implies that the function represented by this option is not supported." OBJECT traceRouteCtlMiscOptions MIN-ACCESS read-only DESCRIPTION "Support of this object is optional. If not supporting, do not allow write access and return a zero-length octet string as the value of the object." OBJECT traceRouteCtlStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required. It is also allowed that implementations support only the volatile(2) StorageType enumeration." OBJECT traceRouteCtlType MIN-ACCESS read-only DESCRIPTION "Write access is not required. In addition, the only value that is RECOMMENDED to be supported by an implementation is traceRouteUsingUdpProbes." OBJECT traceRouteResultsIpTgtAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteResultsIpTgtAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteResultsLastGoodPath DESCRIPTION "If the traceRouteHopsTableGroup is implemented, then this object is mandatory for implementations that have access to a system clock and that are capable of setting the values for DateAndTime objects. It is RECOMMENDED that when this object is not supported its values be reported as '0000000000000000'H." OBJECT traceRouteProbeHistoryHAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteProbeHistoryHAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteProbeHistoryTime DESCRIPTION "This object is mandatory for implementations that have access to a system clock and that are capable of setting the values for DateAndTime objects. It is RECOMMENDED that when this object is not supported its values be reported as '0000000000000000'H." OBJECT traceRouteHopsIpTgtAddressType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteHopsIpTgtAddress SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteHopsLastGoodProbe DESCRIPTION "This object is mandatory for implementations that have access to a system clock and that are capable of setting the values for DateAndTime objects. It is RECOMMENDED that when this object is not supported its values be reported as '0000000000000000'H." ::= { traceRouteCompliances 2 } traceRouteMinimumCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The minimum compliance statement for SNMP entities which implement the minimal subset of the DISMAN-TRACEROUTE-MIB. Implementors might choose this subset for small devices with limited resources." MODULE -- this module MANDATORY-GROUPS { traceRouteMinimumGroup } GROUP traceRouteCtlRowStatusGroup DESCRIPTION "A compliant implementation does not have to implement the traceRouteCtlRowStatusGroup." GROUP traceRouteHistoryGroup DESCRIPTION "A compliant implementation does not have to implement the traceRouteHistoryGroup." GROUP traceRouteHopsTableGroup DESCRIPTION "This group lists the objects that make up a traceRouteHopsEntry. Support of the traceRouteHopsTable is optional." GROUP traceRouteNotificationsGroup DESCRIPTION "This group defines a collection of optional notifications." OBJECT traceRouteMaxConcurrentRequests MIN-ACCESS read-only DESCRIPTION "The agent is not required to support SET operations to this object." OBJECT traceRouteCtlByPassRouteTable MIN-ACCESS read-only DESCRIPTION "Write access is not required. If write access is not supported, return a false(2) as the value of this object. A value of false(2) means that the function represented by this option is not supported." OBJECT traceRouteCtlDSField MIN-ACCESS read-only DESCRIPTION "Write access is not required. If write access is not supported, return a 0 as the value of this object. A value of 0 implies that the function represented by this option is not supported." OBJECT traceRouteCtlSourceAddressType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "Write access to this object is not required by implementations that are not capable of binding the send socket with a source address. An implementation is only required to support IPv4 and IPv6 addresses." OBJECT traceRouteCtlSourceAddress SYNTAX InetAddress (SIZE(0|4|16)) MIN-ACCESS read-only DESCRIPTION "Write access to this object is not required by implementations that are not capable of binding the send socket with a source address. An implementation is only required to support IPv4 and IPv6 addresses." OBJECT traceRouteCtlIfIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. If write access is not supported, return a 0 as the value of this object. A value of 0 implies that the function represented by this option is not supported." OBJECT traceRouteCtlMiscOptions MIN-ACCESS read-only DESCRIPTION "Support of this object is optional. If not supporting, do not allow write access, and return a zero-length octet string as the value of the object." OBJECT traceRouteCtlDontFragment MIN-ACCESS read-only DESCRIPTION "Write access is not required. If write access is not supported, return a false(2) as the value of this object. A value of false(2) means that the function represented by this option is not supported." OBJECT traceRouteCtlInitialTtl MIN-ACCESS read-only DESCRIPTION "Write access is not required. If write access is not supported, return a 1 as the value of this object." OBJECT traceRouteCtlFrequency MIN-ACCESS read-only DESCRIPTION "Write access is not required. If write access is not supported, return a 0 as the value of this object. A value of 0 implies that the function represented by this option is not supported." OBJECT traceRouteCtlStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required. It is also allowed that implementations support only the volatile(2) StorageType enumeration." OBJECT traceRouteCtlDescr MIN-ACCESS read-only DESCRIPTION "The agent is not required to support set operations to this object." OBJECT traceRouteCtlMaxRows MIN-ACCESS read-only DESCRIPTION "Write access is not required. If the traceRouteHistoryGroup is not implemented, then write access to this object MUST be disabled, and the object MUST return a value of 0 when retrieved." OBJECT traceRouteCtlTrapGeneration MIN-ACCESS read-only DESCRIPTION "Write access is not required. If the traceRouteNotificationsGroup is not implemented, then write access to this object MUST be disabled, and the object MUST return a value with no bit set when retrieved. No bit set indicates that no notification is generated." OBJECT traceRouteCtlCreateHopsEntries MIN-ACCESS read-only DESCRIPTION "Write access is not required. If the traceRouteHopsTableGroup is not implemented, then write access to this object MUST be disabled, and the object MUST return a value of false(2) when retrieved." OBJECT traceRouteCtlType MIN-ACCESS read-only DESCRIPTION "Write access is not required. In addition, the only value that is RECOMMENDED to be supported by an implementation is traceRouteUsingUdpProbes." OBJECT traceRouteResultsIpTgtAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteResultsIpTgtAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteResultsLastGoodPath DESCRIPTION "This object is mandatory for implementations that have access to a system clock and that are capable of setting the values for DateAndTime objects. It is RECOMMENDED that when this object is not supported its values be reported as '0000000000000000'H." OBJECT traceRouteProbeHistoryHAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteProbeHistoryHAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteProbeHistoryTime DESCRIPTION "If the traceRouteHistoryGroup is implemented, then this object is mandatory for implementations that have access to a system clock and that are capable of setting the values for DateAndTime objects. It is RECOMMENDED that when this object is not supported its values be reported as '0000000000000000'H." OBJECT traceRouteHopsIpTgtAddressType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteHopsIpTgtAddress SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteHopsLastGoodProbe DESCRIPTION "If the traceRouteHopsTableGroup is implemented, then this object is mandatory for implementations that have access to a system clock and that are capable of setting the values for DateAndTime objects. It is RECOMMENDED that when this object is not supported its values be reported as '0000000000000000'H." ::= { traceRouteCompliances 3 } traceRouteCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for the DISMAN-TRACEROUTE-MIB. This compliance statement has been deprecated because the traceRouteGroup and the traceRouteTimeStampGroup have been split and deprecated. The traceRouteFullCompliance is semantically identical to the deprecated traceRouteCompliance statement." MODULE -- this module MANDATORY-GROUPS { traceRouteGroup } GROUP traceRouteTimeStampGroup DESCRIPTION "This group is mandatory for implementations that have access to a system clock and that are capable of setting the values for DateAndTime objects." GROUP traceRouteNotificationsGroup DESCRIPTION "This group defines a collection of optional notifications." GROUP traceRouteHopsTableGroup DESCRIPTION "This group lists the objects that make up a traceRouteHopsEntry. Support of the traceRouteHopsTable is optional." OBJECT traceRouteMaxConcurrentRequests MIN-ACCESS read-only DESCRIPTION "The agent is not required to support SET operations to this object." OBJECT traceRouteCtlByPassRouteTable MIN-ACCESS read-only DESCRIPTION "This object is not required by implementations that are not capable of its implementation. The function represented by this object is implementable if the setsockopt SOL_SOCKET SO_DONTROUTE option is supported." OBJECT traceRouteCtlSourceAddressType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } MIN-ACCESS read-only DESCRIPTION "This object is not required by implementations that are not capable of binding the send socket with a source address. An implementation is only required to support IPv4 and IPv6 addresses." OBJECT traceRouteCtlSourceAddress SYNTAX InetAddress (SIZE(0|4|16)) MIN-ACCESS read-only DESCRIPTION "This object is not required by implementations that are not capable of binding the send socket with a source address. An implementation is only required to support IPv4 and globally unique IPv6 addresses." OBJECT traceRouteCtlIfIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required. When write access is not supported, return a 0 as the value of this object. A value of 0 implies that the function represented by this option is not supported." OBJECT traceRouteCtlMiscOptions MIN-ACCESS read-only DESCRIPTION "Support of this object is optional. When not supporting, do not allow write access, and return a zero-length octet string as the value of the object." OBJECT traceRouteCtlStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required. It is also allowed that implementations support only the volatile StorageType enumeration." OBJECT traceRouteCtlDSField MIN-ACCESS read-only DESCRIPTION "Write access is not required. When write access is not supported, return a 0 as the value of this object. A value of 0 implies that the function represented by this option is not supported." OBJECT traceRouteCtlType MIN-ACCESS read-only DESCRIPTION "Write access is not required. In addition, the only value that is RECOMMENDED to be supported by an implementation is traceRouteUsingUdpProbes." OBJECT traceRouteResultsIpTgtAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteResultsIpTgtAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteProbeHistoryHAddrType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteProbeHistoryHAddr SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteHopsIpTgtAddressType SYNTAX InetAddressType { unknown(0), ipv4(1), ipv6(2) } DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." OBJECT traceRouteHopsIpTgtAddress SYNTAX InetAddress (SIZE(0|4|16)) DESCRIPTION "An implementation should only support IPv4 and globally unique IPv6 address values for this object." ::= { traceRouteCompliances 1 } -- MIB groupings traceRouteMinimumGroup OBJECT-GROUP OBJECTS { traceRouteMaxConcurrentRequests, traceRouteCtlTargetAddressType, traceRouteCtlTargetAddress, traceRouteCtlByPassRouteTable, traceRouteCtlDataSize, traceRouteCtlTimeOut, traceRouteCtlProbesPerHop, traceRouteCtlPort, traceRouteCtlMaxTtl, traceRouteCtlDSField, traceRouteCtlSourceAddressType, traceRouteCtlSourceAddress, traceRouteCtlIfIndex, traceRouteCtlMiscOptions, traceRouteCtlMaxFailures, traceRouteCtlDontFragment, traceRouteCtlInitialTtl, traceRouteCtlFrequency, traceRouteCtlStorageType, traceRouteCtlAdminStatus, traceRouteCtlMaxRows, traceRouteCtlTrapGeneration, traceRouteCtlDescr, traceRouteCtlCreateHopsEntries, traceRouteCtlType, traceRouteResultsOperStatus, traceRouteResultsCurHopCount, traceRouteResultsCurProbeCount, traceRouteResultsIpTgtAddrType, traceRouteResultsIpTgtAddr, traceRouteResultsTestAttempts, traceRouteResultsTestSuccesses, traceRouteResultsLastGoodPath } STATUS current DESCRIPTION "The group of objects that constitute the remote traceroute operation." ::= { traceRouteGroups 5 } traceRouteCtlRowStatusGroup OBJECT-GROUP OBJECTS { traceRouteCtlRowStatus } STATUS current DESCRIPTION "The RowStatus object of the traceRouteCtlTable." ::= { traceRouteGroups 6 } traceRouteHistoryGroup OBJECT-GROUP OBJECTS { traceRouteProbeHistoryHAddrType, traceRouteProbeHistoryHAddr, traceRouteProbeHistoryResponse, traceRouteProbeHistoryStatus, traceRouteProbeHistoryLastRC, traceRouteProbeHistoryTime } STATUS current DESCRIPTION "The group of objects that constitute the history capability." ::= { traceRouteGroups 7 } traceRouteNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { traceRoutePathChange, traceRouteTestFailed, traceRouteTestCompleted } STATUS current DESCRIPTION "The notifications that are required to be supported by implementations of this MIB." ::= { traceRouteGroups 3 } traceRouteHopsTableGroup OBJECT-GROUP OBJECTS { traceRouteHopsIpTgtAddressType, traceRouteHopsIpTgtAddress, traceRouteHopsMinRtt, traceRouteHopsMaxRtt, traceRouteHopsAverageRtt, traceRouteHopsRttSumOfSquares, traceRouteHopsSentProbes, traceRouteHopsProbeResponses, traceRouteHopsLastGoodProbe } STATUS current DESCRIPTION "The group of objects that constitute the traceRouteHopsTable." ::= { traceRouteGroups 4 } traceRouteGroup OBJECT-GROUP OBJECTS { traceRouteMaxConcurrentRequests, traceRouteCtlTargetAddressType, traceRouteCtlTargetAddress, traceRouteCtlByPassRouteTable, traceRouteCtlDataSize, traceRouteCtlTimeOut, traceRouteCtlProbesPerHop, traceRouteCtlPort, traceRouteCtlMaxTtl, traceRouteCtlDSField, traceRouteCtlSourceAddressType, traceRouteCtlSourceAddress, traceRouteCtlIfIndex, traceRouteCtlMiscOptions, traceRouteCtlMaxFailures, traceRouteCtlDontFragment, traceRouteCtlInitialTtl, traceRouteCtlFrequency, traceRouteCtlStorageType, traceRouteCtlAdminStatus, traceRouteCtlMaxRows, traceRouteCtlTrapGeneration, traceRouteCtlDescr, traceRouteCtlCreateHopsEntries, traceRouteCtlType, traceRouteCtlRowStatus, traceRouteResultsOperStatus, traceRouteResultsCurHopCount, traceRouteResultsCurProbeCount, traceRouteResultsIpTgtAddrType, traceRouteResultsIpTgtAddr, traceRouteResultsTestAttempts, traceRouteResultsTestSuccesses, traceRouteProbeHistoryHAddrType, traceRouteProbeHistoryHAddr, traceRouteProbeHistoryResponse, traceRouteProbeHistoryStatus, traceRouteProbeHistoryLastRC } STATUS deprecated DESCRIPTION "The group of objects that constitute the remote traceroute operation." ::= { traceRouteGroups 1 } traceRouteTimeStampGroup OBJECT-GROUP OBJECTS { traceRouteResultsLastGoodPath, traceRouteProbeHistoryTime } STATUS deprecated DESCRIPTION "The group of DateAndTime objects." ::= { traceRouteGroups 2 } END