DECNET-PHIV-MIB DEFINITIONS ::= BEGIN IMPORTS Gauge FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 mib-2, DisplayString FROM RFC1213-MIB; -- DECNet Phase-IV MIB phiv OBJECT IDENTIFIER ::= { mib-2 18 } -- textual conventions PhivAddr ::= OCTET STRING (SIZE (2)) -- This data type is intended as a short word representation of -- standard DECnet Phase IV addresses. DECnet addresses are -- hierarchically structured numbers assigned to a particular -- DECnet node. The address is structured so that the area -- number is contained in the most significant 6 bits of the -- first octet. The next 2 bits of the first octet contain -- the first two bits of the host address. The remainder of -- the host address is contained in the second octet. PhivCounter ::= INTEGER -- This data type has been created for DECnet counters. These -- counters latch at their maximum specified value until either -- the system is restarted, or they are reset to zero by the user -- or management software. InterfaceIndex ::= INTEGER -- The range of ifIndex, i.e., (1..2147483647) -- groups in the decnetiv mib phivSystem OBJECT IDENTIFIER ::= { phiv 1 } phivManagement OBJECT IDENTIFIER ::= { phiv 2 } session OBJECT IDENTIFIER ::= { phiv 3 } end OBJECT IDENTIFIER ::= { phiv 4 } routing OBJECT IDENTIFIER ::= { phiv 5 } circuit OBJECT IDENTIFIER ::= { phiv 6 } ddcmp OBJECT IDENTIFIER ::= { phiv 7 } control OBJECT IDENTIFIER ::= { phiv 8 } ethernet OBJECT IDENTIFIER ::= { phiv 9 } counters OBJECT IDENTIFIER ::= { phiv 10 } adjacency OBJECT IDENTIFIER ::= { phiv 11 } line OBJECT IDENTIFIER ::= { phiv 12 } nonBroadcastLine OBJECT IDENTIFIER ::= { phiv 14 } area OBJECT IDENTIFIER ::= { phiv 15 } -- System Group -- The implementation of the System Group is mandatory for -- all systems. phivSystemState OBJECT-TYPE SYNTAX INTEGER { on (1), off (2), shut (3), restricted (4) } ACCESS read-write STATUS mandatory DESCRIPTION "This represents the operational state of the executor node. The possible states are: ON Allows logical links. OFF Allows no new links, terminates existing links, and stops routing traffic through. SHUT Allows no new logical links, does not destroy existing logical links, and goes to the OFF state when all logical links are gone. RESTRICTED Allows no new incoming logical links from other nodes. NOTE: These values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155)." ::= { phivSystem 1 } phivExecIdent OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) ACCESS read-write STATUS mandatory DESCRIPTION "This is a text string that describes the executor node (for example, 'Research Lab'). The string is up to 32 characters of any type." ::= { phivSystem 2 } -- Network Management Group -- The implementation of the Network Management Group is -- mandatory for all systems which contain a DECnet-style -- management version. phivMgmtMgmtVers OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "This is the read-only Network Management Version, consisting of the version number, the Engineering Change Order (ECO) number, and the user ECO number (for example, 3.0.0). This parameter applies to the executor node only." ::= { phivManagement 1 } -- Session Layer Group -- The implementation of the Session Layer Group is optional. -- A system can be said to implement this group if and only if -- all objects in this group are implemented. phivSessionSystemName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..6)) ACCESS read-only STATUS mandatory DESCRIPTION "Name to be associated with the node identification. Only one name can be assigned to a node address or a circuit identification. No name should be used more than once in a DECnet network. Node-name is one to six upper case alphanumeric characters with at least one alpha character. A length of 0 indicates no name." ::= { session 1 } phivSessionInTimer OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum duration between the time a connect is received for a process at the executor node and the time that process accepts or rejects it. If the connect is not accepted or rejected by the user within the number of seconds specified, Session Control rejects it for the user. A value of 0 indicates no timer is running." ::= { session 2 } phivSessionOutTimer OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the duration between the time the executor requests a connect and the time that connect is acknowledged by the destination node. If the connect is not acknowledged within the number of seconds specified, Session Control returns an error. A value of 0 indicates no timer is running." ::= { session 3 } -- End Communication Layer Group -- The implementation of the End Communication Layer Group is optional. -- A system can be said to implement this group if and only if -- all objects in this group are implemented. -- Remote State Table phivEndRemoteTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivEndRemoteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about the state of sessions between the node under study and the nodes found in the table." ::= { end 1 } phivEndRemoteEntry OBJECT-TYPE SYNTAX PhivEndRemoteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about a particular remote node as seen from the end communication layer." INDEX { phivEndRemoteHostNodeID } ::= { phivEndRemoteTable 1 } PhivEndRemoteEntry ::= SEQUENCE { phivEndRemoteHostNodeID PhivAddr, phivEndRemoteState INTEGER, phivEndCircuitIndex INTEGER, phivEndActiveLinks INTEGER, phivEndDelay INTEGER } phivEndRemoteHostNodeID OBJECT-TYPE SYNTAX PhivAddr -- OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "This value is the address of the remote node to be evaluated." ::= { phivEndRemoteEntry 1 } phivEndRemoteState OBJECT-TYPE SYNTAX INTEGER { on (1), off (2), shut (3), restricted (4) } ACCESS read-write STATUS mandatory DESCRIPTION "This represents the operational state of the remote node being evaluated. The possible states are: ON Allows logical links. OFF Allows no new links, terminates existing links, and stops routing traffic through. SHUT Allows no new logical links, does not destroy existing logical links, and goes to the OFF state when all logical links are gone. RESTRICTED Allows no new incoming logical links from other nodes. NOTE: These values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155." ::= { phivEndRemoteEntry 2 } phivEndCircuitIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "A unique index value for each known circuit used to communicate with the remote node. This is the same value as phivCircuitIndex." ::= { phivEndRemoteEntry 3 } phivEndActiveLinks OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This read-only parameter represents the number of active logical links from the executor to the destination node." ::= { phivEndRemoteEntry 4 } phivEndDelay OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This read-only parameter is the average round trip delay in seconds to the destination node. This parameter is kept on a remote node basis." ::= { phivEndRemoteEntry 5 } -- End System Counter Table phivEndCountTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivEndCountEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about the counters associated with each end system that is known to the entity. These counters reflect totals from the perspective of the executor node." ::= { end 2 } phivEndCountEntry OBJECT-TYPE SYNTAX PhivEndCountEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about a particular session between two end systems." INDEX { phivEndCountHostNodeID } ::= { phivEndCountTable 1 } PhivEndCountEntry ::= SEQUENCE { phivEndCountHostNodeID PhivAddr, phivEndCountSecsLastZeroed PhivCounter, phivEndCountUsrBytesRec PhivCounter, phivEndCountUsrBytesSent PhivCounter, phivEndUCountUsrMessRec PhivCounter, phivEndCountUsrMessSent PhivCounter, phivEndCountTotalBytesRec PhivCounter, phivEndCountTotalBytesSent PhivCounter, phivEndCountTotalMessRec PhivCounter, phivEndCountTotalMessSent PhivCounter, phivEndCountConnectsRecd PhivCounter, phivEndCountConnectsSent PhivCounter, phivEndCountReponseTimeouts PhivCounter, phivEndCountRecdConnectResErrs PhivCounter } phivEndCountHostNodeID OBJECT-TYPE SYNTAX PhivAddr -- OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "This value is the address of the remote node to be evaluated." ::= { phivEndCountEntry 1 } phivEndCountSecsLastZeroed OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This value is the number of seconds that have elapsed since the counters for the node in this table row were last set to zero. This counter is located in the network management layer, but is returned with the end system information which follows." ::= { phivEndCountEntry 2 } phivEndCountUsrBytesRec OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of user bytes received from the target host." ::= { phivEndCountEntry 3 } phivEndCountUsrBytesSent OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of user bytes sent to the target host." ::= { phivEndCountEntry 4 } phivEndUCountUsrMessRec OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of user messages received from the target host." ::= { phivEndCountEntry 5 } phivEndCountUsrMessSent OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of user messages sent to the target host." ::= { phivEndCountEntry 6 } phivEndCountTotalBytesRec OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes received from the target host." ::= { phivEndCountEntry 7 } phivEndCountTotalBytesSent OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes sent to the target host." ::= { phivEndCountEntry 8 } phivEndCountTotalMessRec OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of messages received from the target host." ::= { phivEndCountEntry 9 } phivEndCountTotalMessSent OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of messages sent to the target host." ::= { phivEndCountEntry 10 } phivEndCountConnectsRecd OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of connects received from the target host." ::= { phivEndCountEntry 11 } phivEndCountConnectsSent OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of connects sent to the target host." ::= {phivEndCountEntry 12 } phivEndCountReponseTimeouts OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of response timeouts." ::= { phivEndCountEntry 13 } phivEndCountRecdConnectResErrs OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of received connect resource errors." ::= {phivEndCountEntry 14 } -- additional End System objects phivEndMaxLinks OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum active logical link count allowed for the executor." ::= { end 3 } phivEndNSPVers OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "This read-only parameter represents the version number of the node End Communication S/W. The format is version number, ECO, and user ECO, e.g., 4.1.0" ::= { end 4 } phivEndRetransmitFactor OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum number of times the source End Communication at the executor node will restart the retransmission timer when it expires. If the number is exceeded, Session Control disconnects the logical link for the user." ::= { end 5 } phivEndDelayFact OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "This is the number by which to multiply one sixteenth of the estimated round trip delay to a node to set the retransmission timer to that node." ::= { end 6 } phivEndDelayWeight OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "This number represents the weight to apply to a current round trip delay estimate to a remote node when updating the estimated round trip delay to a node. On some systems the number must be 1 less than a power of 2 for computational efficiency." ::= { end 7 } phivEndInactivityTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum duration of inactivity (no data in either direction) on a logical link before the node checks to see if the logical link still works. If no activity occurs within the minimum number of seconds, End Communication generates artificial traffic to test the link (End Communication specification)." ::= { end 8 } phivEndCountZeroCount OBJECT-TYPE SYNTAX INTEGER { other (1), reset (2) } ACCESS read-write STATUS mandatory DESCRIPTION "When this value is set to 2, all of the counters in the End System Counter Table are set to zero." ::= { end 9 } phivEndMaxLinksActive OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the high water mark for the number of links that were active at any one time." ::= { end 10 } -- Routing Layer Group -- The implementation of the Routing Layer Group is mandatory for -- all systems that implement level 1 routing layer -- communications. phivRouteBroadcastRouteTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value determines the maximum time in seconds allowed between Routing updates on Ethernet circuits. When this timer expired before a routing update occurs, a routing update is forced. With a standard calculation, Routing also uses this timer to enforce a minimum delay between routing updates." ::= { routing 1 } phivRouteBuffSize OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This parameter value determines the maximum size of a Routing message. It therefore determines the maximum size message that can be forwarded. This size includes protocol overhead down to and including the End Communication layer, plus a constant value of 6. (This value of 6 is included to provide compatibility with the parameter definition in Phase III, which included the Routing overhead.) It does not include Routing or Data link overhead (except for the constant value of 6). There is one buffer size for all circuits. NOTE: The BUFFER SIZE defines the maximum size messages that the Routing layer can forward. The SEGMENT BUFFER SIZE (defined below) defines the maximum size messages that the End Communication layer can transmit or receive. The SEGMENT BUFFER SIZE is always less than or equal to the BUFFER SIZE. Normally the two parameters will be equal. They may be different to allow the network manager to alter buffer sizes on all nodes without interruption of service. They both include an extra 6 bytes for compatibility with Phase III." ::= { routing 2 } phivRouteRoutingVers OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS mandatory DESCRIPTION "This read-only parameter identifies the executor node's Routing version number. The format is version number, ECO, and user ECO, e.g., 4.1.0" ::= { routing 3 } phivRouteMaxAddr OBJECT-TYPE SYNTAX INTEGER (1..1023) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the largest node number and, therefore, number of nodes that can be known about by the executor node's home area." ::= { routing 4 } phivRouteMaxBdcastNonRouters OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum total number of nonrouters the executor node can have on its Ethernet circuits." ::= { routing 5 } phivRouteMaxBdcastRouters OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum total number of routers the executor node can have on its Ethernet circuits." ::= { routing 6 } phivRouteMaxBuffs OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum number of transmit buffers that Routing may use for all circuits." ::= { routing 7 } phivRouteMaxCircuits OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum number of Routing circuits that the executor node can know about." ::= { routing 8 } phivRouteMaxCost OBJECT-TYPE SYNTAX INTEGER (1..1022) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum total path cost allowed from the executor to any node within an area. The path cost is the sum of the circuit costs along a path between two nodes. This parameter defines the point where the executor node's Routing routing decision algorithm declares another node unreachable because the cost of the least costly path to the other node is excessive. For correct operation, this parameter must not be less than the maximum path cost of the network." ::= { routing 9 } phivRouteMaxHops OBJECT-TYPE SYNTAX INTEGER (1..30) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum number of routing hops allowable from the executor to any other reachable node within an area. (A hop is the logical distance over a circuit between two adjacent nodes.) This parameter defines the point where the executor node's Routing routing decision algorithm declares another node unreachable because the length of the shortest path between the two nodes is too long. For correct operation, this parameter must not be less than the network diameter. (The network diameter is the reachability distance between the two nodes of the network having the greatest reachability distance, where reachability distance is the length the shortest path between a given pair of nodes.)" ::= { routing 10 } phivRouteMaxVisits OBJECT-TYPE SYNTAX INTEGER (1..63) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum number of nodes a message coming into the executor node can have visited. If the message is not for this node and the MAXIMUM VISITS number is exceeded, the message is discarded. The MAXIMUM VISITS parameter defines the point where the packet lifetime control algorithm discards a packet that has traversed too many nodes. For correct operation, this parameter must not be less than the maximum path length of the network. (The maximum path length is the routing distance between the two nodes of the network having the greatest routing distance, where routing distance is the length of the least costly path between a given pair of nodes.)" ::= { routing 11 } phivRouteRoutingTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value determines the maximum time in seconds allowed between Routing updates on non-Ethernet circuits. When this timer expires before a routing update occurs, a routing update is forced." ::= { routing 12 } phivRouteSegBuffSize OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This parameter value determines the maximum size of an end-to-end segment. The size is a decimal integer in the range 1-65535. This size is in bytes. This size includes protocol overhead down to and including the End Communication layer, plus a constant value of 6. (This value of 6 is included to provide compatibility with the BUFFER SIZE parameter definition.) It does not include Routing or Data link overhead (except for the constant value of 6)." ::= { routing 13 } phivRouteType OBJECT-TYPE SYNTAX INTEGER { routing-III (1), nonrouting-III (2), area (3), routing-IV (4), nonrouting-IV (5) } ACCESS read-only STATUS obsolete DESCRIPTION "This parameter indicates the type of the executor node. The node-type is one of the following: routing-III nonrouting-III routing-IV ronrouting-IV area A routing node has full routing capability. A nonrouting node contains a subset of the Routing routing modules. The III and IV indicate the DNA phase of the node. Nonrouting nodes can deliver and receive packets to and from any node, but cannot route packets from other nodes through to other nodes. An area node routes between areas. Refer to the Routing specification for details. For adjacent nodes, this is a read-only parameter that indicates the type of the reachable adjacent node. NOTE: The ROUTING-III and NONROUTING-III values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155)" ::= { routing 14 } phivRouteCountAgedPktLoss OBJECT-TYPE SYNTAX PhivCounter (0..127) ACCESS read-only STATUS mandatory DESCRIPTION "Number of aged packet losses." ::= { routing 15 } phivRouteCountNodeUnrPktLoss OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of node unreachable packet losses." ::= { routing 16 } phivRouteCountOutRngePktLoss OBJECT-TYPE SYNTAX PhivCounter (0..127) ACCESS read-only STATUS mandatory DESCRIPTION "Number of node out-of-range packet losses." ::= { routing 17 } phivRouteCountOverSzePktLoss OBJECT-TYPE SYNTAX PhivCounter (0..127) ACCESS read-only STATUS mandatory DESCRIPTION "Number of Oversized packet losses." ::= { routing 18 } phivRouteCountPacketFmtErr OBJECT-TYPE SYNTAX PhivCounter (0..127) ACCESS read-only STATUS mandatory DESCRIPTION "Number of packet format errors." ::= { routing 19 } phivRouteCountPtlRteUpdtLoss OBJECT-TYPE SYNTAX PhivCounter (0..127) ACCESS read-only STATUS mandatory DESCRIPTION "Number of partial routing update losses." ::= { routing 20 } phivRouteCountVerifReject OBJECT-TYPE SYNTAX PhivCounter (0..127) ACCESS read-only STATUS mandatory DESCRIPTION "Number of verification rejects." ::= { routing 21 } -- Level 1 Routing Table phivLevel1RouteTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivLevel1RouteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about the currently known DECnet Phase IV Routes." ::= { routing 22 } phivLevel1RouteEntry OBJECT-TYPE SYNTAX PhivLevel1RouteEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about the currently known DECnet Phase IV Routes." INDEX { phivLevel1RouteNodeAddr } ::= { phivLevel1RouteTable 1 } PhivLevel1RouteEntry ::= SEQUENCE { phivLevel1RouteNodeAddr PhivAddr, phivLevel1RouteCircuitIndex INTEGER, phivLevel1RouteCost INTEGER, phivLevel1RouteHops INTEGER, phivLevel1RouteNextNode PhivAddr } phivLevel1RouteNodeAddr OBJECT-TYPE SYNTAX PhivAddr -- OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "This value is the address of the node about which routing information is contained in this level 1 routing table." ::= { phivLevel1RouteEntry 1 } phivLevel1RouteCircuitIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "A unique index value for each known circuit. This is the index to the circuit state table and is the same value as phivCircuitIndex." ::= { phivLevel1RouteEntry 2 } phivLevel1RouteCost OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This read-only parameter represents the total cost over the current path to the destination node. Cost is a positive integer value associated with using a circuit. Routing routes messages (data) along the path between two nodes with the smallest cost. COST is kept on a remote node basis." ::= { phivLevel1RouteEntry 3 } phivLevel1RouteHops OBJECT-TYPE SYNTAX INTEGER (0..127) ACCESS read-only STATUS mandatory DESCRIPTION "This read-only parameter represents the number of hops over to a destination node. A hop is Routing value representing the logical distance between two nodes in a network. HOPS is kept on a remote node basis." ::= { phivLevel1RouteEntry 4 } phivLevel1RouteNextNode OBJECT-TYPE SYNTAX PhivAddr -- OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "This read-only value indicates the next node on the circuit used to get to the node under scrutiny (next hop)." ::= { phivLevel1RouteEntry 5 } -- Additional routing parameters phivRouteCountZeroCount OBJECT-TYPE SYNTAX INTEGER { other (1), reset (2) } ACCESS read-write STATUS mandatory DESCRIPTION "When this value is set to 2, the following objects are set to Zero: phivRouteCountAgedPktLoss, phivRouteCountNodeUnrPktLoss, phivRouteCountOutRngePktLoss, phivRouteCountOverSzePktLoss, phivRouteCountPacketFmtErr, phivRouteCountPtlRteUpdtLoss, and phivRouteCountVerifReject." ::= { routing 23 } phivRouteSystemAddr OBJECT-TYPE SYNTAX PhivAddr -- OCTET STRING (SIZE (2)) ACCESS read-only STATUS obsolete DESCRIPTION "DECnet Phase IV node address." ::= { routing 24 } phivRouteRoutingType OBJECT-TYPE SYNTAX INTEGER { routing-III (1), nonrouting-III (2), area (3), routing-IV (4), nonrouting-IV (5) } ACCESS read-write STATUS mandatory DESCRIPTION "This read-write parameter indicates the type of the executor node. The node-type is one of the following: routing-III nonrouting-III routing-IV ronrouting-IV area A routing node has full routing capability. A nonrouting node contains a subset of the Routing routing modules. The III and IV indicate the DNA phase of the node. Nonrouting nodes can deliver and receive packets to and from any node, but cannot route packets from other nodes through to other nodes. An area node routes between areas. Refer to the Routing specification for details. For adjacent nodes, this is a read-only parameter that indicates the type of the reachable adjacent node. NOTE: The ROUTING-III and NONROUTING-III values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155)" ::= { routing 25 } phivRouteSystemAddress OBJECT-TYPE SYNTAX PhivAddr -- OCTET STRING (SIZE (2)) ACCESS read-write STATUS mandatory DESCRIPTION "DECnet Phase IV node address." ::= { routing 26 } -- Circuit Group -- The implementation of the Circuit Group is mandatory for -- all systems. -- Circuit Parameters Table phivCircuitParametersTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivCircuitParametersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about the parameters associated with all circuits currently known." ::= {circuit 1 } phivCircuitParametersEntry OBJECT-TYPE SYNTAX PhivCircuitParametersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Parameters information about all circuits currently known." INDEX { phivCircuitIndex } ::= { phivCircuitParametersTable 1 } PhivCircuitParametersEntry ::= SEQUENCE { phivCircuitIndex INTEGER, phivCircuitLineIndex INTEGER, phivCircuitCommonState INTEGER, phivCircuitCommonSubState INTEGER, phivCircuitCommonName DisplayString, phivCircuitExecRecallTimer INTEGER, phivCircuitCommonType INTEGER, phivCircuitService INTEGER, phivCircuitExecCost INTEGER, phivCircuitExecHelloTimer INTEGER } phivCircuitIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "A unique index value for each known circuit." ::= { phivCircuitParametersEntry 1 } phivCircuitLineIndex OBJECT-TYPE SYNTAX InterfaceIndex ACCESS read-only STATUS mandatory DESCRIPTION "The line on which this circuit is active. This is the same as the ifIndex." ::= { phivCircuitParametersEntry 2 } phivCircuitCommonState OBJECT-TYPE SYNTAX INTEGER { on (1), off (2), service (3), cleared (4) } ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the circuit's Network Management operational state. NOTE: These values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155." ::= { phivCircuitParametersEntry 3 } phivCircuitCommonSubState OBJECT-TYPE SYNTAX INTEGER { starting (1), reflecting (2), looping (3), loading (4), dumping (5), triggering (6), autoservice (7), autoloading (8), autodumping (9), autotriggering (10), synchronizing (11), failed (12), running (13) } ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the circuit's Network Management operational and service substate. NOTE: These values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155." ::= { phivCircuitParametersEntry 4 } phivCircuitCommonName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "The name of the circuit entry in the table, for example, SVA-0 or in a level 2 router ASYNC-8 or ETHER-1)." ::= { phivCircuitParametersEntry 5 } phivCircuitExecRecallTimer OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This parameter represents the minimum number of seconds to wait before restarting the circuit. A value of 0 indicates not timer is running." ::= { phivCircuitParametersEntry 6 } phivCircuitCommonType OBJECT-TYPE SYNTAX INTEGER { ddcmp-point (1), ddcmp-control (2), ddcmp-tributary (3), x25 (4), ddcmp-dmc (5), ethernet (6), ci (7), qp2-dte20 (8), bisync (9), other (14), fddi (15) } ACCESS read-only STATUS mandatory DESCRIPTION "Represents the type of the circuit. For X.25 circuits, the value must be set to X25. For DDCMP and Ethernet circuits it is read only and is the same value as the protocol of the associated line. NOTE: Values 1 - 5 are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155." ::= { phivCircuitParametersEntry 7 } phivCircuitService OBJECT-TYPE SYNTAX INTEGER { enabled (1), disabled (2) } ACCESS read-write STATUS mandatory DESCRIPTION "This value indicates whether or not Network Management allows service operations on a circuit. The values for service-control are as follows: ENABLED SERVICE state and/or service functions are allowed. DISABLED SERVICE state and/or service functions are not allowed. NOTE: These values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155." ::= { phivCircuitParametersEntry 8 } phivCircuitExecCost OBJECT-TYPE SYNTAX INTEGER (1..25) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the routing cost of the circuit. Routing sends messages along the path between two nodes having the smallest cost." ::= { phivCircuitParametersEntry 9 } phivCircuitExecHelloTimer OBJECT-TYPE SYNTAX INTEGER (1..8191) ACCESS read-write STATUS mandatory DESCRIPTION "This value determines the frequency of Routing Hello messages sent to the adjacent node on the circuit." ::= { phivCircuitParametersEntry 10 } -- Circuit Counters Table phivCircuitCountTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivCircuitCountEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about the counters associated with all circuits currently known." ::= { circuit 2 } phivCircuitCountEntry OBJECT-TYPE SYNTAX PhivCircuitCountEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Counter information about all circuits currently known" INDEX { phivCircuitIndex } ::= { phivCircuitCountTable 1 } PhivCircuitCountEntry ::= SEQUENCE { phivCircuitCountSecLastZeroed PhivCounter, phivCircuitCountTermPacketsRecd PhivCounter, phivCircuitCountOriginPackSent PhivCounter, phivCircuitCountTermCongLoss PhivCounter, phivCircuitCountCorruptLoss PhivCounter, phivCircuitCountTransitPksRecd PhivCounter, phivCircuitCountTransitPkSent PhivCounter, phivCircuitCountTransitCongestLoss PhivCounter, phivCircuitCountCircuitDown PhivCounter, phivCircuitCountInitFailure PhivCounter, phivCircuitCountAdjDown PhivCounter, phivCircuitCountPeakAdj PhivCounter, phivCircuitCountBytesRecd PhivCounter, phivCircuitCountBytesSent PhivCounter, phivCircuitCountDataBlocksRecd PhivCounter, phivCircuitCountDataBlocksSent PhivCounter, phivCircuitCountUsrBuffUnav PhivCounter } phivCircuitCountSecLastZeroed OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of seconds since the circuit counters for this circuit were last zeroed." ::= { phivCircuitCountEntry 1 } phivCircuitCountTermPacketsRecd OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of terminating packets received on this circuit." ::= { phivCircuitCountEntry 2 } phivCircuitCountOriginPackSent OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of originating packets sent on this circuit." ::= { phivCircuitCountEntry 3 } phivCircuitCountTermCongLoss OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of terminating congestion losses on this circuit." ::= { phivCircuitCountEntry 4 } phivCircuitCountCorruptLoss OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of corruption losses on this circuit." ::= { phivCircuitCountEntry 5 } phivCircuitCountTransitPksRecd OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of Transit packets received on this circuit." ::= { phivCircuitCountEntry 6 } phivCircuitCountTransitPkSent OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of transit packets sent on this circuit." ::= { phivCircuitCountEntry 7 } phivCircuitCountTransitCongestLoss OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of transit congestion losses on this circuit." ::= { phivCircuitCountEntry 8 } phivCircuitCountCircuitDown OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of circuit downs on this circuit." ::= { phivCircuitCountEntry 9 } phivCircuitCountInitFailure OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of Initialization failures on this circuit." ::= { phivCircuitCountEntry 10 } phivCircuitCountAdjDown OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "This counter indicates the number of adjacency losses that result from any of the following: Node listener timeout Invalid data received at node listener Unexpected control (initialization or verification) message received Routing message received with a checksum error Node identification from a routing message or a Hello message that is not the one expected Hello message received indicating that connectivity became one-way Adjacency idled." ::= { phivCircuitCountEntry 11 } phivCircuitCountPeakAdj OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This counter indicates the maximum number of nodes that are up on the circuit." ::= { phivCircuitCountEntry 12 } phivCircuitCountBytesRecd OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes received on this circuit." ::= { phivCircuitCountEntry 13 } phivCircuitCountBytesSent OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes sent on this circuit." ::= { phivCircuitCountEntry 14 } phivCircuitCountDataBlocksRecd OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of data blocks received on this circuit." ::= { phivCircuitCountEntry 15 } phivCircuitCountDataBlocksSent OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of data blocks sent on this circuit." ::= { phivCircuitCountEntry 16 } phivCircuitCountUsrBuffUnav OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of user buffer unavailable errors." ::= { phivCircuitCountEntry 17 } -- Additional Circuit Parameters phivCircuitOrigQueueLimit OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "This parameter indicates the maximum number of originating packets that may be outstanding on this circuit. This does not include route-thru traffic." ::= { circuit 3 } phivCircuitCountZeroCount OBJECT-TYPE SYNTAX INTEGER { other (1), reset (2) } ACCESS read-write STATUS mandatory DESCRIPTION "When this value is set to 2, all of the counters in the Circuit Counter Table are set to zero." ::= { circuit 4 } -- DDCMP Circuit Group -- The implementation of the DDCMP Circuit Group is optional. -- A system can be said to implement this group if and only if -- all objects in this group are implemented. -- DDCMP Parameters Table phivDDCMPCircuitParametersTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivDDCMPCircuitParametersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about DDCMP circuit parameters." ::= { ddcmp 1} phivDDCMPCircuitParametersEntry OBJECT-TYPE SYNTAX PhivDDCMPCircuitParametersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Parameters information about DDCMP circuits currently known." INDEX { phivDDCMPCircuitIndex } ::= { phivDDCMPCircuitParametersTable 1 } PhivDDCMPCircuitParametersEntry ::= SEQUENCE { phivDDCMPCircuitIndex INTEGER, phivDDCMPCircuitAdjNodeAddr INTEGER, phivDDCMPCircuitTributary INTEGER } phivDDCMPCircuitIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "A unique index value for each known DDCMP circuit. This is the same value as phivCircuitIndex." ::= { phivDDCMPCircuitParametersEntry 1 } phivDDCMPCircuitAdjNodeAddr OBJECT-TYPE SYNTAX PhivAddr -- OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "The address of the adjacent node." ::= { phivDDCMPCircuitParametersEntry 2 } phivDDCMPCircuitTributary OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the Data Link physical tributary address of the circuit." ::= { phivDDCMPCircuitParametersEntry 3 } -- DDCMP Circuit Counter Table phivDDCMPCircuitCountTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivDDCMPCircuitCountEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about the DDCMP counters associated with all circuits currently known." ::= { ddcmp 2 } phivDDCMPCircuitCountEntry OBJECT-TYPE SYNTAX PhivDDCMPCircuitCountEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Counter information about DDCMP circuits now known" INDEX { phivCircuitIndex } ::= { phivDDCMPCircuitCountTable 1 } PhivDDCMPCircuitCountEntry ::= SEQUENCE { phivDDCMPCircuitErrorsInbd PhivCounter, phivDDCMPCircuitErrorsOutbd PhivCounter, phivDDCMPCircuitRmteReplyTimeouts PhivCounter, phivDDCMPCircuitLocalReplyTimeouts PhivCounter, phivDDCMPCircuitRmteBuffErrors PhivCounter, phivDDCMPCircuitLocalBuffErrors PhivCounter, phivDDCMPCircuitSelectIntervalsElap PhivCounter, phivDDCMPCircuitSelectTimeouts PhivCounter } phivDDCMPCircuitErrorsInbd OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of Data errors inbound." ::= { phivDDCMPCircuitCountEntry 1 } phivDDCMPCircuitErrorsOutbd OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of outbound data errors." ::= { phivDDCMPCircuitCountEntry 2 } phivDDCMPCircuitRmteReplyTimeouts OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of remote reply timeouts." ::= { phivDDCMPCircuitCountEntry 3 } phivDDCMPCircuitLocalReplyTimeouts OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of local Reply timeouts." ::= { phivDDCMPCircuitCountEntry 4 } phivDDCMPCircuitRmteBuffErrors OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of remote reply time out errors." ::= { phivDDCMPCircuitCountEntry 5 } phivDDCMPCircuitLocalBuffErrors OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of local buffer errors." ::= { phivDDCMPCircuitCountEntry 6 } phivDDCMPCircuitSelectIntervalsElap OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Selection intervals that have elapsed." ::= {phivDDCMPCircuitCountEntry 7 } phivDDCMPCircuitSelectTimeouts OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of selection timeouts." ::= {phivDDCMPCircuitCountEntry 8 } -- DDCMP Line Count Table phivDDCMPLineCountTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivDDCMPLineCountEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The DDCMP Line Count Table." ::= { ddcmp 3 } phivDDCMPLineCountEntry OBJECT-TYPE SYNTAX PhivDDCMPLineCountEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "There is one entry in the table for each line." INDEX { phivDDCMPLineCountIndex } ::= { phivDDCMPLineCountTable 1 } PhivDDCMPLineCountEntry ::= SEQUENCE { phivDDCMPLineCountIndex InterfaceIndex, phivDDCMPLineCountDataErrsIn PhivCounter, phivDDCMPLineCountRmteStationErrs PhivCounter, phivDDCMPLineCountLocalStationErrs PhivCounter } phivDDCMPLineCountIndex OBJECT-TYPE SYNTAX InterfaceIndex ACCESS read-only STATUS mandatory DESCRIPTION "The line on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of phivLineIndex. This value is the ifIndex." ::= { phivDDCMPLineCountEntry 1 } phivDDCMPLineCountDataErrsIn OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of data errors inbound." ::= { phivDDCMPLineCountEntry 2 } phivDDCMPLineCountRmteStationErrs OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of remote station errors." ::= { phivDDCMPLineCountEntry 3 } phivDDCMPLineCountLocalStationErrs OBJECT-TYPE SYNTAX PhivCounter (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Number of local station errors." ::= { phivDDCMPLineCountEntry 4 } -- DDCMP Multipoint Circuit Control Group -- The implementation of the DDCMP Multipoint Circuit Control -- Group is optional. A system can be said to implement this group -- if and only if all objects in this group are implemented. phivControlSchedTimer OBJECT-TYPE SYNTAX INTEGER (50..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the number of milliseconds between recalculation of tributary polling priorities." DEFVAL { 200 } ::= { control 1 } phivControlDeadTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the number of milliseconds between polls of one of the set of dead tributaries." DEFVAL { 10000 } ::= { control 2 } phivControlDelayTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the minimum number of milliseconds to delay between polls. The delay timer limits the effect of a very fast control station on slow tributaries." ::= { control 3 } phivControlStreamTimer OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the number of milliseconds a tributary or a half duplex remote station is allowed to hold the line. NOTE: This parameter can also be applied to half-duplex lines of type DDCMP POINT." DEFVAL { 6000 } ::= { control 4 } -- DDCMP Multipoint Circuit Control Parameters Table phivControlParametersTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivControlParametersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about control circuit parameters." ::= { control 5 } phivControlParametersEntry OBJECT-TYPE SYNTAX PhivControlParametersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Parameters information about control circuits currently known." INDEX { phivControlCircuitIndex } ::= { phivControlParametersTable 1 } PhivControlParametersEntry ::= SEQUENCE { phivControlCircuitIndex INTEGER, phivControlBabbleTimer INTEGER, phivControlMaxBuffs INTEGER, phivControlMaxTransmits INTEGER, phivControlDyingBase INTEGER, phivControlDyingIncrement INTEGER, phivControlDeadThreshold INTEGER, phivControlDyingThreshold INTEGER, phivControlInactTreshold INTEGER, phivControlPollingState INTEGER, phivControlPollingSubState INTEGER, phivControlTransTimer INTEGER } phivControlCircuitIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "A unique index value for each known multipoint control circuit. This is the same value as phivCircuitIndex." ::= { phivControlParametersEntry 1 } phivControlBabbleTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the number of milliseconds that a selected tributary or remote half-duplex station is allowed to transmit." DEFVAL { 6000 } ::= { phivControlParametersEntry 2 } phivControlMaxBuffs OBJECT-TYPE SYNTAX INTEGER (1..254) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum number of buffers the tributary can use from a common buffer pool. If not set, there is no common buffer pool and buffers are explicitly supplied by the higher level. Count is a decimal integer in the range 1-254." ::= { phivControlParametersEntry 3 } phivControlMaxTransmits OBJECT-TYPE SYNTAX INTEGER (1..255) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum number of data messages that can be transmitted at one time. Count is a decimal integer in the range 1-255." DEFVAL { 4 } ::= { phivControlParametersEntry 4 } phivControlDyingBase OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the base priority to which a tributary is reset each time it has been polled. A separate base can be set for each of the indicated polling states. Base is a decimal integer in the range 0-255. If not set, the defaults are: active, 255; inactive, 0; and dying, 0." ::= { phivControlParametersEntry 5 } phivControlDyingIncrement OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the increment added to the tributary priority each time the scheduling timer expires. If not set, the defaults are: active, 0; inactive, 64; and dying, 16." ::= { phivControlParametersEntry 6 } phivControlDeadThreshold OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the number of times to poll the active, inactive, or dying tributary before changing its polling state to dead because of receive timeouts. Count is a decimal integer in the range 0-255." DEFVAL { 8 } ::= { phivControlParametersEntry 7 } phivControlDyingThreshold OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the number of times to poll the active or inactive tributary before changing its polling state to dying because of receive timeouts. Count is a decimal integer in the range 0-255." DEFVAL { 2 } ::= { phivControlParametersEntry 8 } phivControlInactTreshold OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the number of times to poll the active tributary before changing its polling state to inactive because of no data response. Count is a decimal integer in the range 0-255." DEFVAL { 8 } ::= { phivControlParametersEntry 9 } phivControlPollingState OBJECT-TYPE SYNTAX INTEGER { automatic (1), active (2), inactive (3), dying (4), dead (5) } ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the state of the tributary relative to the multipoint polling algorithm. If not set the default is AUTOMATIC. The possible states are: AUTOMATIC The tributary's state is allowed to vary according to the operation of the polling algorithm. ACTIVE/INACTIVE/DYING/DEAD The tributary is locked in the specified state. NOTE: These values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155." ::= { phivControlParametersEntry 10 } phivControlPollingSubState OBJECT-TYPE SYNTAX INTEGER { active (1), inactive (2), dying (3), dead (4) } ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the tributary's state as determined by the polling algorithm. This applies only when the polling state is AUTOMATIC and is read-only to Network Management. Polling-substate is one of ACTIVE, INACTIVE, DYING, or DEAD. It is displayed as a tag on the polling state, for example: AUTOMATIC-INACTIVE." ::= { phivControlParametersEntry 11 } phivControlTransTimer OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the number of milliseconds to delay between data message transmits. Milliseconds is a decimal integer in the range 0-65535." DEFVAL { 0 } ::= { phivControlParametersEntry 12 } -- Ethernet Group -- The implementation of the Ethernet Group is mandatory -- for all systems which support ethernet links. -- Ethernet Parameters Table phivEthLinkParametersTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivEthLinkParametersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about ethernet link parameters." ::= { ethernet 1} phivEthLinkParametersEntry OBJECT-TYPE SYNTAX PhivEthLinkParametersEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Parameter information about ethernet links currently known." INDEX { phivEthLinkIndex } ::= { phivEthLinkParametersTable 1 } PhivEthLinkParametersEntry ::= SEQUENCE { phivEthLinkIndex INTEGER, phivEthDesigRouterNodeAddr PhivAddr, phivEthMaxRouters INTEGER, phivEthRouterPri INTEGER, phivEthHardwareAddr OCTET STRING } phivEthLinkIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "The circuit over which this links information is collected. This is the same as phivCircuitIndex." ::= { phivEthLinkParametersEntry 1 } phivEthDesigRouterNodeAddr OBJECT-TYPE SYNTAX PhivAddr -- OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "This value is the address of the designated router." ::= { phivEthLinkParametersEntry 2 } phivEthMaxRouters OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "This parameter is the maximum number of routers (other than the executor itself) allowed on the circuit by Routing for circuits that are owned by the executor node." ::= { phivEthLinkParametersEntry 3 } phivEthRouterPri OBJECT-TYPE SYNTAX INTEGER (0..127) ACCESS read-write STATUS mandatory DESCRIPTION "This parameter is the priority that this router is to have in the selection of designated router for the circuit on circuits that are owned by the executor node." DEFVAL { 64 } ::= { phivEthLinkParametersEntry 4 } phivEthHardwareAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "This read-only parameter is the address that is associated with the line device hardware as seen by the DECnet Software. This value is not the same as ifPhysAddress." ::= { phivEthLinkParametersEntry 5 } -- Counters Group -- The implementation of the Counters Group is optional. -- A system can be said to implement this group if and only if -- all objects in this group are implemented. -- Counters Table phivCountersCountTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivCountersCountEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Information about ethernet link counters." ::= { counters 1 } phivCountersCountEntry OBJECT-TYPE SYNTAX PhivCountersCountEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Counter information about ethernet links currently known." INDEX { phivCountersIndex } ::= { phivCountersCountTable 1 } PhivCountersCountEntry ::= SEQUENCE { phivCountersIndex InterfaceIndex, phivCountersCountBytesRecd PhivCounter, phivCountersCountBytesSent PhivCounter, phivCountersCountDataBlocksRecd PhivCounter, phivCountersCountDataBlocksSent PhivCounter, phivCountersCountEthUsrBuffUnav PhivCounter, phivCountersCountMcastBytesRecd PhivCounter, phivCountersCountDataBlksRecd PhivCounter, phivCountersCountDataBlksSent PhivCounter, phivCountersCountMcastBlksRecd PhivCounter, phivCountersCountBlksSentDef PhivCounter, phivCountersCountBlksSentSingleCol PhivCounter, phivCountersCountBlksSentMultCol PhivCounter, phivCountersCountSendFailure PhivCounter, phivCountersCountCollDetectFailure PhivCounter, phivCountersCountReceiveFailure PhivCounter, phivCountersCountUnrecFrameDest PhivCounter, phivCountersCountDataOver PhivCounter, phivCountersCountSysBuffUnav PhivCounter, phivCountersCountUsrBuffUnav PhivCounter } phivCountersIndex OBJECT-TYPE SYNTAX InterfaceIndex ACCESS read-only STATUS mandatory DESCRIPTION "The interface to which these counters apply. This is the same interface as identified by the same value of phivLineIndex. This value is the ifIndex." ::= { phivCountersCountEntry 1 } phivCountersCountBytesRecd OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes received over this link." ::= { phivCountersCountEntry 2 } phivCountersCountBytesSent OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of bytes sent over this link." ::= { phivCountersCountEntry 3 } phivCountersCountDataBlocksRecd OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS obsolete DESCRIPTION "Number of data blocks received over this link." ::= { phivCountersCountEntry 4 } phivCountersCountDataBlocksSent OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS obsolete DESCRIPTION "Number of data blocks sent over this link." ::= { phivCountersCountEntry 5 } phivCountersCountEthUsrBuffUnav OBJECT-TYPE SYNTAX PhivCounter (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of user buffer unavailable errors over this link." ::= { phivCountersCountEntry 6 } phivCountersCountMcastBytesRecd OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of multicast bytes received over this link." ::= { phivCountersCountEntry 7 } phivCountersCountDataBlksRecd OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of data blocks received over this link." ::= { phivCountersCountEntry 8 } phivCountersCountDataBlksSent OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of data blocks sent over this link." ::= { phivCountersCountEntry 9 } phivCountersCountMcastBlksRecd OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of multicast blocks received over this link." ::= { phivCountersCountEntry 10 } phivCountersCountBlksSentDef OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of blocks sent, initially deferred over this link." ::= { phivCountersCountEntry 11 } phivCountersCountBlksSentSingleCol OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of blocks sent, single collision over this link." ::= { phivCountersCountEntry 12 } phivCountersCountBlksSentMultCol OBJECT-TYPE SYNTAX PhivCounter (0..2147483647) ACCESS read-only STATUS mandatory DESCRIPTION "Number of blocks sent, multiple collisions over this link." ::= { phivCountersCountEntry 13 } phivCountersCountSendFailure OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of send failures over this link." ::= { phivCountersCountEntry 14 } phivCountersCountCollDetectFailure OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of collision detect check failures over this link." ::= { phivCountersCountEntry 15 } phivCountersCountReceiveFailure OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of receive failures over this link." ::= { phivCountersCountEntry 16 } phivCountersCountUnrecFrameDest OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of unrecognized frame destinations over this link." ::= { phivCountersCountEntry 17 } phivCountersCountDataOver OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of data overruns over this link." ::= { phivCountersCountEntry 18 } phivCountersCountSysBuffUnav OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of system buffer unavailables over this link." ::= { phivCountersCountEntry 19 } phivCountersCountUsrBuffUnav OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "Number of user buffer unavailables." ::= { phivCountersCountEntry 20 } -- Adjacency Group -- The implementation of the Adjacency Group is mandatory for all -- conformant implementations of this memo. -- The phivAdjTable has been made obsolete it has been replaced with -- the phivAdjNodeTable. phivAdjTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivAdjEntry ACCESS not-accessible STATUS obsolete DESCRIPTION "The Adjacency Table." ::= { adjacency 1 } phivAdjEntry OBJECT-TYPE SYNTAX PhivAdjEntry ACCESS not-accessible STATUS obsolete DESCRIPTION "There is one entry in the table for each adjacency." INDEX { phivAdjCircuitIndex } ::= { phivAdjTable 1 } PhivAdjEntry ::= SEQUENCE { phivAdjCircuitIndex INTEGER, phivAdjNodeAddr PhivAddr, phivAdjBlockSize INTEGER, phivAdjListenTimer INTEGER (1..65535), phivAdjCircuitEtherServPhysAddr OCTET STRING, phivAdjType INTEGER, phivAdjState INTEGER, phivAdjPriority INTEGER, phivAdjExecListenTimer INTEGER (1..65535) } phivAdjCircuitIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS obsolete DESCRIPTION "A unique index value for each known circuit." ::= { phivAdjEntry 1 } phivAdjNodeAddr OBJECT-TYPE SYNTAX PhivAddr -- OCTET STRING (SIZE (2)) ACCESS read-only STATUS obsolete DESCRIPTION "The address of the adjacent node." ::= { phivAdjEntry 2 } phivAdjBlockSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS obsolete DESCRIPTION "This read-only parameter is the block size that was negotiated with the adjacent Routing layer during Routing initialization over a particular circuit. It includes the routing header, but excludes the data link header. This parameter is qualified by ADJACENT NODE." ::= { phivAdjEntry 3 } phivAdjListenTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS obsolete DESCRIPTION "This value determines the maximum number of seconds allowed to elapse before Routing receives some message (either a Hello message or a user message) from the adjacent node on the circuit. It was agreed during Routing initialization with the adjacent Routing layer. This parameter is qualified by ADJACENT NODE." ::= { phivAdjEntry 4 } phivAdjCircuitEtherServPhysAddr OBJECT-TYPE SYNTAX OCTET STRING ( SIZE (6) ) ACCESS read-only STATUS obsolete DESCRIPTION "This parameter indicates the Ethernet physical address of an adjacent node that is being serviced on this circuit. This parameter is a qualifier for SERVICE SUBSTATE." ::= { phivAdjEntry 5 } phivAdjType OBJECT-TYPE SYNTAX INTEGER { routing-III (1), nonrouting-III (2), area (3), routing-IV (4), nonrouting-IV (5) } ACCESS read-only STATUS obsolete DESCRIPTION "This parameter indicates the type of adjacency. For adjacent nodes, this is a read-only parameter that indicates the type of the reachable adjacent node. NOTE: The routing-III and nonrouting-III values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155)" ::= { phivAdjEntry 6 } phivAdjState OBJECT-TYPE SYNTAX INTEGER { initializing (1), -- Ethernet one-way up (2), -- Ethernet two-way run (3), -- The eight DDCMP/X.25 states circuit-rejected (4), data-link-start (5), routing-layer-initialize (6), routing-layer-verify (7), routing-layer-complete (8), off (9), halt (10) } ACCESS read-only STATUS obsolete DESCRIPTION "This value indicates the state of a router adjacency. On adjacencies over a circuit of type (phivCircuitCommonType) Ethernet, CI, or FDDI, with an adjacent node of type (phivAdjType) ROUTING IV or AREA, this variable is the state of the Ethernet Initialization Layer for this adjacency, and can have values INITIALIZING or UP. (See Section 9.1.1 of DECnet Phase IV Routing Layer Functional Specification.) On adjacencies over a circuit of type (phivCircuitCommonType) Ethernet, CI, or FDDI, with an adjacent node of type (phivAdjType) NONROUTING IV, this variable will always take on the value UP. On adjacencies over a circuit of type (phivCircuitCommonType) DDCMP POINT, DDCMP CONTROL, DDCMP TRIBUTARY, DDCMP DMC, or X.25, this variable is the state of the Routing Layer Initialization Circuit State. (See section 7.3, ibid.) It can have values between RUN and HALT. On adjacencies over a circuit of type (phivCircuitCommonType) OTHER, this variable may be used in a manner consistent with the Initialization Layer used on that circuit." ::= { phivAdjEntry 7 } phivAdjPriority OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS obsolete DESCRIPTION "Priority assigned by the adjacent node for this circuit." ::= { phivAdjEntry 8 } phivAdjExecListenTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS obsolete DESCRIPTION "This read-only value determines the maximum number of seconds allowed to elapse before Routing receives some message (either a Hello message or a user message) from the adjacent node on the circuit. It was agreed during Routing initialization with the adjacent Routing layer." ::= { phivAdjEntry 9 } -- New Adjacency Table this replaces the phivAdjTable. phivAdjNodeTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivAdjNodeEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Adjacent Node Table." ::= { adjacency 2 } phivAdjNodeEntry OBJECT-TYPE SYNTAX PhivAdjNodeEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "There is one entry in the table for each adjacency." INDEX { phivAdjNodeCircuitIndex, phivAdjAddr } ::= { phivAdjNodeTable 1 } PhivAdjNodeEntry ::= SEQUENCE { phivAdjNodeCircuitIndex INTEGER, phivAdjAddr PhivAddr, phivAdjNodeBlockSize INTEGER, phivAdjNodeListenTimer INTEGER, phivAdjNodeCircuitEtherServPhysAddr OCTET STRING, phivAdjNodeType INTEGER, phivAdjNodeState INTEGER, phivAdjNodePriority INTEGER } phivAdjNodeCircuitIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "A unique index value for each known circuit. This value is the same as phivCircuitIndex and identifies the circuit over which the adjacency is realized." ::= { phivAdjNodeEntry 1 } phivAdjAddr OBJECT-TYPE SYNTAX PhivAddr -- OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "The address of the adjacent node." ::= { phivAdjNodeEntry 2 } phivAdjNodeBlockSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This read-only parameter is the block size that was negotiated with the adjacent Routing layer during Routing initialization over a particular circuit. It includes the routing header, but excludes the data link header. This parameter is qualified by ADJACENT NODE." ::= { phivAdjNodeEntry 3 } phivAdjNodeListenTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This value determines the maximum number of seconds allowed to elapse before Routing receives some message (either a Hello message or a user message) from the adjacent node on the circuit. It was agreed during Routing initialization with the adjacent Routing layer. This parameter is qualified by ADJACENT NODE." ::= { phivAdjNodeEntry 4 } phivAdjNodeCircuitEtherServPhysAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "This parameter indicates the Ethernet physical address of an adjacent node that is being serviced on this circuit. This parameter is a qualifier for SERVICE SUBSTATE." ::= { phivAdjNodeEntry 5 } phivAdjNodeType OBJECT-TYPE SYNTAX INTEGER { routing-III (1), nonrouting-III (2), area (3), routing-IV (4), nonrouting-IV (5) } ACCESS read-only STATUS mandatory DESCRIPTION "This parameter indicates the type of adjacency. For adjacent nodes, this is a read-only parameter that indicates the type of the reachable adjacent node. NOTE: The routing-III and nonrouting-III values are incremented by one compared to the standard DECnet values in order to maintain compliance with RFC 1155)" ::= { phivAdjNodeEntry 6 } phivAdjNodeState OBJECT-TYPE SYNTAX INTEGER { initializing (1), -- Ethernet one-way up (2), -- Ethernet two-way run (3), -- The eight DDCMP/X.25 states circuit-rejected (4), data-link-start (5), routing-layer-initialize (6), routing-layer-verify (7), routing-layer-complete (8), off (9), halt (10) } ACCESS read-only STATUS mandatory DESCRIPTION "This value indicates the state of a router adjacency. On adjacencies over a circuit of type (phivCircuitCommonType) Ethernet, CI, or FDDI, with an adjacent node of type (phivAdjNodeType) ROUTING IV or AREA, this variable is the state of the Ethernet Initialization Layer for this adjacency, and can have values INITIALIZING or UP. (See Section 9.1.1 of DECnet Phase IV Routing Layer Functional Specification.) On adjacencies over a circuit of type (phivCircuitCommonType) Ethernet, CI, or FDDI, with an adjacent node of type (phivAdjNodeType) NONROUTING IV, this variable will always take on the value UP. On adjacencies over a circuit of type (phivCircuitCommonType) DDCMP POINT, DDCMP CONTROL, DDCMP TRIBUTARY, DDCMP DMC, or X.25, this variable is the state of the Routing Layer Initialization Circuit State. (See section 7.3, ibid.) It can have values between RUN and HALT. On adjacencies over a circuit of type (phivCircuitCommonType) OTHER, this variable may be used in a manner consistent with the Initialization Layer used on that circuit." ::= { phivAdjNodeEntry 7 } phivAdjNodePriority OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "Priority assigned by the adjacent node for this circuit." ::= { phivAdjNodeEntry 8 } -- Line Group -- The implementation of the Line Group is mandatory for all -- conformant implementations of this memo. phivLineTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivLineEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Line Table." ::= { line 1 } phivLineEntry OBJECT-TYPE SYNTAX PhivLineEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "There is one entry in the table for each line." INDEX { phivLineIndex } ::= { phivLineTable 1 } PhivLineEntry ::= SEQUENCE { phivLineIndex InterfaceIndex, phivLineName DisplayString, phivLineState INTEGER, phivLineSubstate INTEGER, phivLineService INTEGER, phivLineDevice DisplayString, phivLineReceiveBuffs INTEGER, phivLineProtocol INTEGER, phivLineServiceTimer INTEGER, phivLineMaxBlock INTEGER } phivLineIndex OBJECT-TYPE SYNTAX InterfaceIndex ACCESS read-only STATUS mandatory DESCRIPTION "The line on which this entry's equivalence is effective. This is the same as the ifIndex." ::= { phivLineEntry 1 } phivLineName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "The name of the line on this row of the table." ::= { phivLineEntry 2 } phivLineState OBJECT-TYPE SYNTAX INTEGER { on (1), off (2), service (3), cleared (4) } ACCESS read-only STATUS mandatory DESCRIPTION "This value represents Network Management operational state. NOTE that these values are incremented by one compared to the standard DECnet values." ::= { phivLineEntry 3 } phivLineSubstate OBJECT-TYPE SYNTAX INTEGER { starting (1), reflecting (2), looping (3), loading (4), dumping (5), triggering (6), auto-service (7), auto-loading (8), auto-dumping (9), auto-triggering (10), synchronizing (11), failed (12), running (13) } ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the line's read-only Network Management substate. NOTE that these values are incremented by one compared to the standard DECnet values." ::= { phivLineEntry 4 } phivLineService OBJECT-TYPE SYNTAX INTEGER { starting (1), reflecting (2), looping (3), other (4) } ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the line's read-only Network Management service. NOTE that these values are incremented by one compared to the standard DECnet values and OTHER is a new addition." ::= { phivLineEntry 5 } phivLineDevice OBJECT-TYPE SYNTAX DisplayString (SIZE (0..16)) ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the Physical Link device to be used on the line." ::= { phivLineEntry 6 } phivLineReceiveBuffs OBJECT-TYPE SYNTAX INTEGER (0..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the number of receive buffers reserved for the line. It is a decimal number in the range 0-65535. 0 is supported for those vendors that do not reserve buffers on a per line basis and use a pool of buffers that can be used by any line." ::= { phivLineEntry 7 } phivLineProtocol OBJECT-TYPE SYNTAX INTEGER { ddcmp-point (1), ddcmp-control (2), ddcmp-tributary (3), reserved (4), ddcmp-dmc (5), olapb (6), ethernet (7), ci (8), qp2 (9), other (14), fddi (15) } ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the protocol used on the line device. Note that these values are incremented by one compared to the standard DECnet values." ::= { phivLineEntry 8 } phivLineServiceTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the amount of time in milliseconds allowed to elapse before a Data Link receive request completes while doing service operations." ::= { phivLineEntry 9 } phivLineMaxBlock OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the Data Link maximum block size on the line." ::= { phivLineEntry 10 } -- Non Broadcast Line Group -- The implementation of the Non Broadcast Line Group is optional. -- A system can be said to implement this group if and only if -- all objects in this group are implemented. phivNonBroadcastTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivNonBroadcastEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Non Broadcast Table." ::= { nonBroadcastLine 1 } phivNonBroadcastEntry OBJECT-TYPE SYNTAX PhivNonBroadcastEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "There is one entry in the table for each Non Broadcast line." INDEX { phivNonBroadcastIndex } ::= { phivNonBroadcastTable 1 } PhivNonBroadcastEntry ::= SEQUENCE { phivNonBroadcastIndex InterfaceIndex, phivNonBroadcastController INTEGER, phivNonBroadcastDuplex INTEGER, phivNonBroadcastClock INTEGER, phivNonBroadcastRetransmitTimer INTEGER } phivNonBroadcastIndex OBJECT-TYPE SYNTAX InterfaceIndex ACCESS read-only STATUS mandatory DESCRIPTION "The Non Broadcast line on which this entry's equivalence is effective. This is the same value as the ifIndex." ::= { phivNonBroadcastEntry 1 } phivNonBroadcastController OBJECT-TYPE SYNTAX INTEGER { normal (1), loopback (2), other (3) } ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the Physical Link hardware controller mode for the line device. The values for controller-mode are: NORMAL For normal controller operating mode. LOOPBACK For software controllable loopback of the controller. On those devices that can support this mode, it causes all transmitted messages to be looped back from within the controller itself. This is accomplished without any manual intervention other than the setting of this parameter value. OTHER indicates function is not supported Note that these values are incremented by one compared to the standard DECnet values." ::= { phivNonBroadcastEntry 2 } phivNonBroadcastDuplex OBJECT-TYPE SYNTAX INTEGER { full (1), half (2) } ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the Physical Link hardware duplex mode of the line device. The possible modes are: FULL Full-duplex HALF Half-duplex Note that these values are incremented by one compared to the standard DECnet values." ::= { phivNonBroadcastEntry 3 } phivNonBroadcastClock OBJECT-TYPE SYNTAX INTEGER { external (1), internal (2), other (3) } ACCESS read-only STATUS mandatory DESCRIPTION "This value represents the Physical Link hardware clock mode for the line device. The values for clock-mode are: INTERNAL For software controllable loopback use of the clock. On those devices that can support this mode, it causes the device to supply a clock signal such that a transmitted messages can be looped back from outside the device. This may require manual intervention other than the setting of this parameter value. For example, the operator may have to connect a loopback plug in place of the normal line. EXTERNAL For normal clock operating mode, where the clock signal is supplied externally to the controller. Note that these values are incremented by one compared to the standard DECnet values." ::= { phivNonBroadcastEntry 4 } phivNonBroadcastRetransmitTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "This value represents number of milliseconds before the Data Link retransmits a block on the line. On half-duplex lines, this parameter is the select timer." DEFVAL { 3000 } ::= { phivNonBroadcastEntry 5 } -- Area Parameters Group -- The implementation of the Area Parameters Group is mandatory -- for all systems which implement level 2 routing. phivAreaTable OBJECT-TYPE SYNTAX SEQUENCE OF PhivAreaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "Table of information kept on all areas known to this unit." ::= { area 1 } phivAreaEntry OBJECT-TYPE SYNTAX PhivAreaEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The area routing information." INDEX { phivAreaNum } ::= { phivAreaTable 1 } PhivAreaEntry ::= SEQUENCE { phivAreaNum INTEGER, phivAreaState INTEGER, phivAreaCost Gauge, phivAreaHops INTEGER, phivAreaNextNode PhivAddr, phivAreaCircuitIndex INTEGER } phivAreaNum OBJECT-TYPE SYNTAX INTEGER (0..64) ACCESS read-only STATUS mandatory DESCRIPTION "This value indicates the area number of this entry." ::= { phivAreaEntry 1 } phivAreaState OBJECT-TYPE SYNTAX INTEGER { reachable (4), unreachable (5) } ACCESS read-only STATUS mandatory DESCRIPTION "This value indicates the state of the area" ::= { phivAreaEntry 2 } phivAreaCost OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The total cost over the current path to the destination area. Cost is a value associated with using a circuit. Routing routes messages (data) along the path between 2 areas with the smallest cost." ::= { phivAreaEntry 3 } phivAreaHops OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-only STATUS mandatory DESCRIPTION "The number of hops to a destination area. A hop is the routing value representing the logical distance between two areas in network." ::= { phivAreaEntry 4 } phivAreaNextNode OBJECT-TYPE SYNTAX PhivAddr -- OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "The next node on the circuit used to get to the area under scrutiny." ::= { phivAreaEntry 5 } phivAreaCircuitIndex OBJECT-TYPE SYNTAX INTEGER (1..65535) ACCESS read-only STATUS mandatory DESCRIPTION "A unique index value for each known circuit." ::= { phivAreaEntry 6 } -- Additional Area Parameters phivAreaMaxCost OBJECT-TYPE SYNTAX INTEGER (1..1022) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum total path cost allowed from the executor to any other level 2 routing node. The AREA MAXIMUM COST number is decimal in the range 1-1022. This parameter is only applicable if the executor node is of type AREA." ::= { area 2 } phivAreaMaxHops OBJECT-TYPE SYNTAX INTEGER (1..30) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the maximum number of routing hops allowable from the executor to any other level 2 routing node. This parameter is only applicable if the executor node is of type AREA." ::= { area 3 } phivRouteMaxArea OBJECT-TYPE SYNTAX INTEGER (1..63) ACCESS read-write STATUS mandatory DESCRIPTION "This value represents the largest area number and, therefore, number of areas that can be known about by the executor node's Routing. This parameter is only applicable if the executor node is of type AREA." ::= { area 4 } END